Journals / Bor Dergisi / 2022 / Cilt: 7 - Sayı: 4

Investigation of the effects of borogypsum and silica fume in silica fume on ceramic material's sintering and final properties

Hafif yapı malzemesi üretiminde borojips ve silis dumanının kullanım potansiyeli

Pages
543–551
Publication Date
2022-12-31
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Consequently, the water absorption and bending strength values obtained in the samples prepared from a mixture of 70% borogypsum and 20% silica fume can be considered the usage as a wall tile is possible since they coincide with the technical properties defined in the EN ISO 10545-3 and EN ISO 10545-4 standards, respectively.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:The present study is aimed at investigating the utilization of two crucial industrial wastes, borogypsum and silica fume, as the main raw materials in the production of building materials.
📊
Key Findings & Data:Mixtures were prepared so that the amount of waste material used in the composition was 90%, and the remaining 10% was binder clay.
💡
Conclusion & Impact:Consequently, the water absorption and bending strength values obtained in the samples prepared from a mixture of 70% borogypsum and 20% silica fume can be considered the usage as a wall tile is possible since they coincide with the technical properties defined in the EN ISO 10545-3 and EN ISO 10545-4 standards, respectively.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Atık · Borojips · Silis Dumanı

Abstract

The present study is aimed at investigating the utilization of two crucial industrial wastes, borogypsum and silica fume, as the main raw materials in the production of building materials. For this aim, different receipts were designed from boron waste (borogypsum) belonging to Emet Boric Acid factory (Kütahya/Turkey) and silica fume, which was taken from Electrometallurgy facilities (Antalya/Turkey). Mixtures were prepared so that the amount of waste material used in the composition was 90%, and the remaining 10% was binder clay. The samples were prepared with different proportions of both wastes were pressed uniaxially at 10 MPa, and the shaped samples were then fired at 1000, 1050, 1100, and 1150 °C. Physical and mechanical tests, as well as mineralogical and microstructural analyses, were carried out on the fired samples. The technical properties of the samples derived from the wastes were evaluated depending on the type of waste material and its usage amounts, and firing temperatures. It has been understood that the use of high Borogypsum will cause high firing loss, which will negatively affect the dimensional stability of the material. Moreover, with silica fume addition to borogypsum, the water absorption and porosity values increased, and the strength values decreased accordingly. Consequently, the water absorption and bending strength values obtained in the samples prepared from a mixture of 70% borogypsum and 20% silica fume can be considered the usage as a wall tile is possible since they coincide with the technical properties defined in the EN ISO 10545-3 and EN ISO 10545-4 standards, respectively.

Özet

Bu çalışmada iki önemli endüstriyel atık olan bor ve silis dumanının yapı malzemeleri üretiminde ana hammadde olarak kullanım imkanı araştırılmıştır. Bu amaçla, Emet Borik Asit fabrikasına (Kütahya/Türkiye) ait bor atığı (borojips) ve Elektrometalurji tesislerinden (Antalya/Türkiye) alınan silis dumanından farklı reçeteler tasarlanmıştır. Karışımlar, bileşimde kullanılan atık malzeme miktarı %90, kalan %10 ise bağlayıcı kil olacak şekilde hazırlanmıştır. Her iki atıktan farklı oranlarda hazırlanan numuneler 10 MPa'da tek eksenli olarak preslenmiş ve şekillendirilen numuneler daha sonra 1000, 1050, 1100 ve 1150 °C' sıcaklıklarda pişirilmiştir. Pişirilen numuneler üzerinde fiziksel ve mekanik testlerin yanı sıra mineralojik ve mikroyapısal analizler gerçekleştirilmiştir. Atıklardan elde edilen numunelerin teknik özellikleri, atık malzemenin türüne, kullanım miktarına ve pişirme sıcaklıklarına bağlı olarak değerlendirilmiştir. Yüksek Borogypsum kullanımının yüksek pişme kaybına neden olacağı, bunun da malzemenin boyutsal stabilitesini olumsuz etkileyeceği anlaşılmıştır. Ayrıca borojipse silis dumanı ilavesi ile su emme ve porozite değerlerinin arttığı, mukavemet değerlerinin ise buna bağlı olarak azaldığı görülmüştür. Sonuç olarak, %70 borojips ve %20 silis dumanı karışımından hazırlanan numunelerde elde edilen su emme ve eğilme dayanımı değerleri sırasıyla EN ISO 10545-3 ve EN ISO 10545-4 standartlarında tanımlanan teknik özelliklerle örtüştüğü için duvar karosu olarak kullanımının mümkün olacağı düşünülebilir.

🔖

Cite This Article

ÖZTÜRK, Ç., EVCİN, A. (2022). Investigation of the effects of borogypsum and silica fume in silica fume on ceramic material's sintering and final properties. Bor Dergisi, Cilt: 7 - Sayı: 4, 543–551. https://ajindex.com/articles/866004

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (1)

  1. S. Baspinar, İ. Demir, M. Orhan, Utilization potential of silica fume in fired clay bricks, Waste Management & Research, 28, 149–157, (2010) 2-A. Sahin Zaimoglu, Engineering properties of sand stabilised with Borogypsum, Proc Inst Civ Eng Geotech Eng, 164, 277-282, (2011) 3- H. M. Şimşek, R. Guliyev, A.V. Beşe, Dissolution kinetics of borogypsum in di-ammonium hydrogen phosphate solutions, International Journal of Hydrogen Energy, 43 (44), 20262-20270, 2018 4- İ. Y. Elbeyli, S. Pişkin, Kinetic study of the thermal dehydration of Borogypsum, Journal of Hazardous Materials, Volume 116, Issues 1–2, 10 December 2004, Pages 111-117 5- K. Kunt, F. Dur, M. Yildirim, E.M. Derun, Effect of chemical admixtures on borogypsum containing cement mortar Main Gr. Chem. (2017), 6- R. Boncukcuoǧlu, M.T. Yilmaz, M.M. Kocakerim, V. Tosunoǧlu, Utilization of borogypsum as set retarder in Portland cement production Cem. Concr. Res. (2002), 7- M. Özdemir, N.U. Öztürk, Utilization of clay wastes containing boron as cement additives Cem. Concr. Res. (2003), 8- U. K. Sevim, M. Ozturk, S. Onturk, M. B. Bankir, Utilization of boron waste borogypsum in mortar, Journal of Building Engineering Volume 22, March 2019, Pages 496-503 9- M. Ozturk, U. K. Sevim, O. Akgol, E. Unal, M. Karaaslan, Investigation of the mechanic, electromagnetic characteristics and shielding effectiveness of concrete with boron ores and boron containing wastes, Construction and Building Materials, 252, 119058, 2020 10- C.B.E. Abi, Effect of borogypsum on brick properties, Construct Build Mater, 59, 195-203, (2014) 11- M. Delfini, M. Ferrini, A. Manni, P. Massacci, L. Piga, Arsenic leaching by Na2S to decontaminate tailings coming from colemanite processing, Miner Eng, 16, 45-50, (2003) 12- F. do, C. Holanda, H. Schmidt, V.A. Quarcioni, Influence of phosphorus from phosphogypsum on the initial hydration of Portland cement in the presence of superplasticizers, Cem. Concr. Compos. (2017) 13- Y. Abali, S.U. Bayca, S. Targan, Evaluation of blends tincal waste, volcanic tuff, bentonite and fly ash for use as a cement admixture J. Hazard. Mater. (2006) 14- D. Över Kaman, L. Köroğlu, E. Ayas, Y. Güney, The effect of heat-treated boron derivative waste at 600 °C on the mechanical and microstructural properties of cement mortar, Constr. Build. Mater. (2017) 15- U.K. Sevim, Colemanite ore waste concrete with low shrinkage and high split tensile strength, Mater. Struct. Constr. (2011), 16- I.Y. Elbeyli, E.M. Derun, J. Güle