SavedAdd your journal

Journals / Health Sciences Quarterly / 2019 / Cilt: 3 - Sayı: 2

USING FIRED WALL TILE’S SCRAPS IN FLOOR TILE BODY

Savaş ELMAS
Pages
133–140
Publication Date
2019-04-30
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

In the XRD analysis, anorthite phase was observed which shows fired strength and chemical resistance.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:The effect of the addition of the fired wall tile’s scraps in floor tile body was studied.
📊
Key Findings & Data:The fired wall tile’s scraps were added to floor tile body according to 1.96-5.66-10.71-17.85 wt. % ratios.
💡
Conclusion & Impact:In the XRD analysis, anorthite phase was observed which shows fired strength and chemical resistance.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Fired scraps wall tiles · Floor tiles · Environment savings

Abstract

The effect of the addition of the fired wall tile’s scraps in floor tile body was studied. The fired wall tile’s scraps were added to floor tile body according to 1.96-5.66-10.71-17.85 wt. % ratios. The sintering behavior of the floor tile was evaluated by measuring the water absorption, fired shrinkage, dry shrinkage and fired strength. In addition, microstructure and phase analysis were investigated by scanning electron microscopy (SEM), energy dispersive x-ray (EDX) and x-ray analysis (XRD). Firing was carried out at 1189 0C for 40 min. in industrial type continuous kiln. It is seen that the addition of 5.66 wt. % of the wall tile’s scrap to the floor tile increases the fired strength value. In the XRD analysis, anorthite phase was observed which shows fired strength and chemical resistance.

🔖

Cite This Article

ELMAS, S. (2019). USING FIRED WALL TILE’S SCRAPS IN FLOOR TILE BODY. Health Sciences Quarterly, Cilt: 3 - Sayı: 2, 133–140. https://ajindex.com/articles/836640

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (9)

  1. KARAMANOV, A., KARAMANOVA, E., FERRARI, A.M., FERRANTE, F., PELINO, M.,2006, The Effects of Fired Scrap Addition on The Sintering Behaviour of Hard Porcelain. Ceramics International, 32, 727-732
  2. NODEH, A.A., 2017, Influence of Bone Porcelain Scraps on The Physical Characterictics and Phase Composition of a Hard Porcelain Body. Ceramica y Vidrio, 56. 113-118, Spain
  3. TORRES, P., FERNANDES, H.R., AGATHOPOULOS, S., TULYAGANOV, D.U., FERREİRA J.M.F., 2004, Incorporation of Granite Cutting Sludge in Industrial Porcelain Tile Formulations, Journal of The European Ceramic Society, 24. 3177-3185
  4. JOUNIORA, A.N., HOTZA, D., SOLER, C.V., VILCHES, E.S., 2010, Influence of Composition on Mechanical Behaviour of Porcelain Tile.Part II: Mechanical Properties and Microscopic Residual Stress, Material Science and Engineering, A 527, 1736-1743
  5. MARTINI, E., FORTUNA, D., FORTUNA, A., RUBINO, G., TAGLIAFERRI, V., 2017, Sanitser, an innovative sanitary ware body, formulated with waste glass and recycled materials, Ceramica, 63, 542-548 [6] LUZ A.P., RİBİERO S., Use of glass waste as a raw material in porcelain stoneware tile mixtures,2007, Ceramics International 33, 761-765 [7] MATTEUCI, F., DONDI, M., GUARINI, G., 2002, Effects of Soda-Lime Glass on Sintering and Technogical Properties of Porcelain Stoeware Tiles, Ceramics International, 28(8) 878-880
  6. GDULA, R.A., 1971, Anorthite ceramic dielectric. Am. Ceram. Soc. Bull., 50(6).555-557
  7. ISMAİL, M.G.M.U., ARAI, H., 1992, Sol-gel Synthesis of B2O3-doped Anorthite and its Characteristics. J. Ceram. Soc. Jpn., 100(12) 1385-1389 [10] POZUTAK, M., SOLVANG, M., DINGWELL, D., 2006, Temperature independent thermal expansivities of calcium aluminosilicates melts between 1150 and 1973 K in the system anorthite- wollastonite-gehlenit: a density model., Geochim Cosmochim Acta, 70. 3059-3074
  8. KURAMA, S., OZEL, E., 2008, The Influence of different CaO source in the Production of Anorthite Ceramics. Ceramics International, 35. 827-830
  9. KARA, A., ÖZER, F., KAYACI, K., ÖZER, P., 2006, Development of a multipurpose tile body: Phase and microstructural development, 26. 3769-3782.