SavedAdd your journal

Journals / Muş Alparslan Üniversitesi Fen Bilimleri Dergisi / 2017 / Cilt: 5 - Sayı: 2

Analysis of the Effects of Drill Bit and Flute Geometry Design on Cutting Force by Taguchi Method

Matkap Uç ve Kanal Geometrisi Tasarımının Kesme Kuvvetleri Üzerindeki Etkilerinin Taguchi Yöntemiyle Analizi

Güven MERAL
Hakan DİLİPAK
Murat SARIKAYA
Ulvi ŞEKER
Pages
435–439
Publication Date
2017-12-01
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

In addition, Taguchi's Signal / Noise (S / N) analysis has been used to determine optimal levels of control factors for best results.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, two original drill channel geometries have been designed and produced.
📊
Key Findings & Data:In the experimental studies , the performance of the two specific flute geometries (Geometry 3 , Geometry 4) developed by two very common tool geometries (Geometry 1, Geometry 2) was tested.
💡
Conclusion & Impact:In addition, Taguchi's Signal / Noise (S / N) analysis has been used to determine optimal levels of control factors for best results.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Delme · Kesme kuvveti · Taguchi metodu

Abstract

In this study, two original drill channel geometries have been designed and produced. In the experimental studies , the performance of the two specific flute geometries (Geometry 3 , Geometry 4) developed by two very common tool geometries (Geometry 1, Geometry 2) was tested. Taguchi’s orthogonal array design of experiment was utilized to investigate the influence of the tool geometry on the drilling performance and to determine the optimal drilling parameters during experimental study. The effect of the input parameters on the experimental results was statistically determined by the Anova analysis. In addition, Taguchi's Signal / Noise (S / N) analysis has been used to determine optimal levels of control factors for best results.

Özet

Bu çalışmada, iki adet özgün matkap kanal geometrisi tasarlanmış ve üretilmiştir. Deneysel çalışmalarda ticari olarak tedarik edilebilen en yaygın iki takım geometrisi (Geometri 1, Geometri 2) ile geliştirilen özgün iki kanal geometrisi (Geometri 3, Geometri 4) performansları test edilmiştir. Takım geometrilerinin delik delme performansı üzerindeki etkilerini araştırmak ve ideal işleme parametrelerinin belirlemek için Taguchi deney tasarımı kullanılmıştır. Anova analizi ile giriş parametrelerinin deney sonuçları üzerindeki etkisi istatistiksel olarak bulunmuştur. Ayrıca Taguchi’nin Sinyal/Gürültü (S/G) analizi, yardımıyla en iyi sonuç için kontrol faktörlerinin optimum seviyeleri belirlenmiştir.

🔖

Cite This Article

MERAL, G., DİLİPAK, H., SARIKAYA, M., ŞEKER, U. (2017). Analysis of the Effects of Drill Bit and Flute Geometry Design on Cutting Force by Taguchi Method. Muş Alparslan Üniversitesi Fen Bilimleri Dergisi, Cilt: 5 - Sayı: 2, 435–439. https://ajindex.com/articles/792977

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (16)

  1. Öztürk, S. Spiral Matkap Uç Geometrileri ve Talaş Kaldırmaya Etkileri, Yüksek Lisans Tezi, Yıldız Teknik Üniversitesi Fen Bilimleri Enstitüsü, İstanbul, 7-8, 2001.
  2. Abele, E., ve Fujara, M.Simulationbasedtwistdrilldesignandgeometryoptimization, CIRP Annals-ManufacturingTecnology, 59(1), 145-150, 2010.
  3. Tsao, C.C. Investigationintotheeffects of drillingparameters on delaminationbyvarious step-coredrills, Journal of MaterialsProcessingTecnology, 206(1-3), 405-411, 2008.
  4. Ogawa, M, Inose, M.,Arai, M., ve Saga T. Micro drilling of 5056 wroughtaluminumalloy, Journal of Japan Institute of LightMetals (Japan), 44(9), 486-491, 1994.
  5. Armerago, E.J.A., ve Cheng, O.Y. DrillingWithFlatFaceandCanventionalTwistDrill-II. ExperimentalInvestigation, Int. J. Mach. ToolDes. Res., 12, 37- 54, 1972.
  6. Hoshi, T. ve Zhao, H. Study of a High PerformanceDrillGeometry, Annals of the CIRP Vol. 38(1), 87-90, 1989.
  7. Paul, A.,Kapoor, S.G., ve Devor, R.E. Chiseledgeandcuttinglipshapeoptimizationforimprovedtwistdrillpointdesign, International Journal of Machine Tools andManufacture, 45(4-5), 421-431, 2005.
  8. Saini, D. P., ve Woodall, P. Drill life optimisationwhendrilling TI-6AL-4V with HSS drills, ICME 9th International Conference on ManufacturingExcellence, 1-12, 2003.
  9. Hsieh, J.F., ve Lin, P.D. Production of multifluteddrills on six-axis CNC tool-grindingmachine, International Journal of Machine Tools andManufacture, 43, 1117-1127, 2003.
  10. Hsieh, J.F. Mathematical model forhelicaldrillpoint, International Journal of Machine Tools andManufacture, 45, 967-977, 2005.
  11. Tsai, W.D., ve Wu, S.M. Mathematical model of multiflutedrillpoint, International Journal of Machine Tools andManufacture, 19, 109-120, 1979.
  12. Lin, P.D., ve Hsieh.J.F. Mathematical model forhelicaldrillpoint, International Journal of Machine Tools andManufacture, 42, 1181–1193, 2002.
  13. Devries, M.F. ve Crosheck, M.K. An Investigation of theCuttingMechanisms of the New Point Drill, Annals of the CIRP Vol. 371(1), 73-78, 1988.
  14. Rubenstein, C.,TheTorqueandThrust Force in TwistDrilling – I.Theory, Int. J. Mach. ToolDes. Manufact., 31(4), 481-489, 1991. Dröse,J. Titannitrid-Beschichtete HSS SpiralBohrerLeistungfähigkeitundVerschleissmechanismen, Doctoraldissertation, RWTH AachenUniversity, Aachen, 1-26, 1987.
  15. SECO Tools. Delik Delme Sunum, İstanbul: SECO Tools, 3-4, 2013.
  16. Savaşkan, M., Taptık, Y., Üregen M. Deney tasarımı yöntemiyle matkap uçlarında performans optimizasyonu. İstanbul Teknik Üniversitesi Mühendislik Dergisi, 3(6), 117-128, 2004