It was found that the temperature of the heat treatment affected significantly the crystallite size and morphology and SrO samples can be easily prepared in high purity via a wet chemical method as a facile route.
📌 3 Key Takeaways
🎯
Objective & Hypothesis:In this study, two strontium oxide (SrO) samples were produced at two different temperatures of 950 °C and 1000 °C, and the characterization of these samples was carried out using X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, and scanning electron microscopy (SEM).
📊
Key Findings & Data:The as-obtained results were compared with both each other and the available data in the literature, and all the as-observed results were reported in more detail.
💡
Conclusion & Impact:It was found that the temperature of the heat treatment affected significantly the crystallite size and morphology and SrO samples can be easily prepared in high purity via a wet chemical method as a facile route.
In this study, two strontium oxide (SrO) samples were produced at two different temperatures of 950 °C and 1000 °C, and the characterization of these samples was carried out using X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, and scanning electron microscopy (SEM). The as-obtained results were compared with both each other and the available data in the literature, and all the as-observed results were reported in more detail. It was found that the temperature of the heat treatment affected significantly the crystallite size and morphology and SrO samples can be easily prepared in high purity via a wet chemical method as a facile route.
INCE, T., ATEŞ, T., BULUT, N., KESER, S., KAYGİLİ, O. (2021). Characterization of SrO samples produced at two different temperatures. Journal of Physical Chemistry and Functional Materials, Cilt: 4 - Sayı: 1, 13–16. https://ajindex.com/articles/778289
Referans1 F. Méar, P. Yot, M. Cambon and M. Ribes, Waste Management, 2006, 26, 1468-1476. Referans2 T. Athar, Materials Focus, 2013, 2, 450-453. Referans3 B.D. Cullity, Elements of X-ray diffraction, Addison-Wesley Publishing Company; 1978. Referans4 M.H.M. Abdelrehman, Synthesis and characterization of bismuth doped strontium oxide powder and thin films, Master of Science Thesis, 2019,
University of the Free State, Republic of South Africa. Referans5 M.M. Rahman, M.M. Hussain and A.M. Asiri, RSC Advances, 2016, 6, 65338. Referans6 G. Apsana, P.P. George, N. Devanna and R. Yuvasravana, Asian Journal of Pharmaceutical and Clinical Research, 2018, 11, 384-389. Referans7 F. Granados-Correa and J. Bonifacio-Martinez, Materials Science-Poland, 2014, 32, 682-687. Referans8 A.A. Gungor, H. Nadaroglu and D.D. Gultekin, Chemical Science International Journal, 2019, 26, 1-7. Referans9 Alimuddin and M. Rafeeq, Oriental Journal of Chemistry, 2021, 37, 177-180. Referans10 H. Li, F. Liu, X. Ma, Z. Wu, Y. Li, L. Zhang, S. Zhou and Y. Helian, Energy Conversion and Management, 2019, 180, 401-410. Referans11 H. Li, F. Liu, X. Ma, P. Cui, M. Guo, Y. Li, Y. Gao, S. Zhou and M. Yu, Renewable Energy, 2020, 149, 816-827. Referans12 S.S. Bhoware, M.S. Maubane, A. Shaikjee, I. Beas, A. Ziegler and N.J. Coville, Materials Research Bulletin, 2013, 48, 2347-2350. Referans13 S. Harish, M. Sabarinathan, J. Archana, M. Navaneethan, K.D. Nisha, S. Ponnusamy, V. Gupta, C. Muthamizhchelvan, D.K. Aswal, H. Ikeda and Y.Hayakawa, Applied Surface Science, 2017, 418, 147-155.