Journals / Journal of New Results in Science / 2018 / Cilt: 7 - Sayı: 2

Investigation of 3D Printing Occupancy Rates Effect on Mechanical Properties and Surface Roughness of PET-G Material Products

Pages
1–8
Publication Date
2018-08-28
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The results were analyzed and compared.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Recent developments in 3D printing are attracting wide spread interest due to easily accessible with lower cost.
📊
Key Findings & Data:The present paper aims to investigate printing occupancy rates effect on mechanical properties and surface roughness of PET-G (Polietilen Tereftalat Glikol) material products.
💡
Conclusion & Impact:The results were analyzed and compared.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:3D Printer · PET-G · Printing Occupancy Rate

Abstract

Recent developments in 3D printing are attracting wide spread interest due to easily accessible with lower cost. The present paper aims to investigate printing occupancy rates effect on mechanical properties and surface roughness of PET-G (Polietilen Tereftalat Glikol) material products. Pet-G material was preferred because of its malleability, colorability and mechanical properties. PET-G products were printed at different printing occupancy rates (20%, 50% and 80%) at processing speed of 45 mm/s and all other operating parameters fixed at the same conditions on 3D printer. Uniaxial tensile tests, hardness measurements and surface roughness measurements of the printed products were carried out. The results were analyzed and compared.

🔖

Cite This Article

İPEKÇİ, A., Kam, M., Saruhan, H. (2018). Investigation of 3D Printing Occupancy Rates Effect on Mechanical Properties and Surface Roughness of PET-G Material Products. Journal of New Results in Science, Cilt: 7 - Sayı: 2, 1–8. https://ajindex.com/articles/777849

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (13)

  1. Ahrabi A.Z., 2009. Pet Atıkları Kullanılarak Kompozit Malzeme Üretiminin Araştırılması, Ankara Üniversitesi Fen Bilimleri Enstitüsü Yüksek Lisans Tezi, Kimya Mühendisliği anabilim Dalı, Ankara.
  2. Bernard, Fischer, A., 2012. New Trends in Rapid Product Development, Industrial Engineering Research. Billiet, T., Vandenhaute, M., Schelfhout, J., Vlierberghe, S. V., Dubruel, P., 2012. A Review of Trends And Limitations In Hydrogel Rapid Prototyping For Tissue Engineering, Biomaterials 33, 6020-6041.
  3. Birtchnell, T., Urry, J., 2013. 3D, SF And The Future, Futures 50, 25-34.
  4. Calvert, P., 1998.
  5. Free Forming of Polymers, Polymers, 585-588
  6. Campbell, I., Bourell, D. and Gibson, I., 2012. Additive Manufacturing: Rapid Prototyping Comes Of Age, Rapid Prototyping Journal,18 (4): 255-258.
  7. Campbell, I., Bourell, D., Gibson, I., 2012. Additive Manufacturing: Rapid Prototyping Comes of Age, Rapid Prototyping Journal, 255-258.
  8. Çelik, D., 2015. Tersine Mühendislikle Üç Boyutlu Yazıcı Tasarımı ve Üretimi Yüksek Lisans Tezi, Karabük Üni., Fen Bil. Enstitüsü. Chimento, J., Jason, M., Nathan Crane, H., 2011. 3D Printed Tooling for Thermoforming of Medical Devices, Rapid Prototyping Journal, 387 –392. Dale Prince, 2014. 3D Printing: An Industrial Revolution, Journal of Electronic Resources in Medical Libraries, 39-45.
  9. Fantini, M., Crescenzio, F. D., Persiani, F., Benazzi, S., Gruppioni, G., 2008. 3D Restitution, Restoration And Prototyping of A Medieval Damaged Skull, Rapid Prototyping Journal,318 –324. Günther D., Heymel B., Günther F. J. and Ederer I., 2014. Continuous 3D Printing for Additive Manufacturing, Rapid Prototyping Journal, 20 (4): 320327. Kashdan, L., Seepersad, C. C., Haberman, M., Wilson, P. S., 2012.
  10. Design, Fabrication, And Evaluation of Negative Stiffness Elements Using SLS, Rapid Prototyping Journal,194-200.
  11. Kroll, E. and Artzi, D., 2011. Enhancing Aerospace Engineering Students Learning With 3D Printing Wind-Tunnel Models, Rapid Prototyping Journal,17 (5): 393 -402. Lee, C.S., Kim, S.G., Kim, H.J., Ahn, S.H., 2007. Measurement of Anisotropic Compressive Strength of Rapid Prototyping Parts, Journal of Materials Processing Technology, 627–630.
  12. Levy, G. N., Schindel, R. and Kruth, J. P., 1996. Rapid Manufacturing And Rapid Tooling With Layer Manufacturıng (Lm) Technologies, State of The Art And Future Perspectives, 1 (1): 1-21.
  13. Marchelli, G., Prabhakar, R., Storti, D., Ganter, M., 2011. The Guide to Glass 3D Printing: Developments, Methods, Diagnostics And Results,