Journals / Politeknik Dergisi / 2022 / Cilt: 25 - Sayı: 2

High-Speed Machining Process of Titanium Alloy: A Comprehensive Finite Element Modeling

Titanyum Alaşımının Yüksek-Hızlı İşleme Süreci: Kapsamlı Sonlu Eleman Modelleme

Pages
813–826
Publication Date
2022-06-01
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The results also show that an increase in the positive direction of rake angle causes a decrease in cutting force and a smoother workpiece surface.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:This study comprehensively deals with a two-dimensional finite element (FE) modeling and simulation for chip formation process of titanium alloy.
📊
Key Findings & Data:During the serrated chip formation, the primary deformation region exhibits substantially higher stress than secondary region.
💡
Conclusion & Impact:The results also show that an increase in the positive direction of rake angle causes a decrease in cutting force and a smoother workpiece surface.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Talaş oluşumu · SE modelleme · yüksek-hızlı işletme

Abstract

This study comprehensively deals with a two-dimensional finite element (FE) modeling and simulation for chip formation process of titanium alloy. The basic parameters, such as chip shape, workpiece surface, equivalent stress, plastic strain and cutting force, are analyzed to study the impact of a variety of rake angles during high-speed machining. The chip shapes vary with the tool-rake angle. During the serrated chip formation, the primary deformation region exhibits substantially higher stress than secondary region. Also, the higher strains are occurred at the chip roots. The fluctuation of the cutting force caused by the serrated chip is more prominent than that obtained during the continuous chip formation, and the force varies periodically. The results also show that an increase in the positive direction of rake angle causes a decrease in cutting force and a smoother workpiece surface.

Özet

Bu çalışma, titanyum alaşımının talaş oluşumu süreci için iki boyutlu sonlu eleman (SE) modelleme ve benzetimini kapsamlı bir şekilde ele almaktadır. Yüksek hızlı işleme sırasında çeşitli talaş açılarının etkisini incelemek için talaş şekli, iş parçası yüzeyi, eşdeğer gerilme, plastik gerinim ve kesme kuvveti gibi temel parametreler analiz edilmiştir. Talaş şekilleri, takım talaş açısıyla değişmektedir. Testere ağızlı talaş oluşumu sırasında, birincil deformasyon bölgesi, ikincil bölgeden önemli ölçüde daha yüksek gerilme sergilemektedir. Ayrıca, yüksek gerinimler talaş köklerinde meydana gelmiştir. Testere ağızlı talaşın neden olduğu kesme kuvveti dalgalanması, sürekli talaş oluşumu sırasında elde edilenden daha belirgindir ve kuvvet periyodik olarak değişmektedir. Sonuçlar, talaş açısının pozitif yöndeki artışının kesme kuvvetinde azalmaya ve daha pürüzsüz bir iş parçası yüzeyine yol açtığını da göstermektedir.

🔖

Cite This Article

AYDIN, M. (2022). High-Speed Machining Process of Titanium Alloy: A Comprehensive Finite Element Modeling. Politeknik Dergisi, Cilt: 25 - Sayı: 2, 813–826. https://ajindex.com/articles/697063

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (14)

  1. Aydın M., “Dik kesme işleminde kalıcı gerilmelerin sonlu elemanlar yöntemiyle modellenmesi”, Politeknik Dergisi, 19(3): 297–304, (2016)
  2. Al-Zkeri I., Rech J., Altan T., Hamdi H. and Valiorgue F., “Optimization of the cutting edge geometry of coated carbide tools in dry turning of steels using a finite element analysis”, Machining Science and Technology, 13: 36–51, (2009)
  3. Aydin M., “Prediction of cutting speed interval of diamond-coated tools with residual stress”, Materials and Manufacturing Processes, 32: 145–150, (2017)
  4. Gao C. and Zhang L., “Effect of cutting conditions on the serrated chip formation in high-speed cutting”, Machining Science and Technology, 17: 26–40, (2013)
  5. Gökçe H., Çiftçi İ. ve Gökçe H., “Frezeleme operasyonlarında kesme kuvvetlerinin deneysel ve sonlu elemanlar analizi ile incelenmesi: saf molibdenin işlenmesi üzerine bir çalışma”, Politeknik Dergisi, 22(4): 947–954, (2019)
  6. Kurt A. ve Şeker U., “Kesici takım gerilmelerinin sonlu elemanlar metodu kullanılarak incelenmesi”, Gazi Üniversitesi Mühendislik Mimarlık Fakültesi Dergisi, 20(4): 491–497, (2005)
  7. Akgün M. and Demir H., “Optimization and finite element modelling of tool wear in milling of Inconel 625 superalloy”, Journal of Polytechnic, https://doi.org/ 10.2339/politeknik.706605
  8. Kong X., Li B., Jin Z. and Geng W., “Broaching performance of superalloy GH4169 based on FEM”, Journal of Materials Science and Technology, 27: 1178–1184, (2011)
  9. Komanduri R. and Turkovich B.F., “New observations on the mechanism of chip formation when machining titanium alloys”, Wear, 69: 179–188, (1981)
  10. Duan C.Z. and Zhang L.C., “Adiabatic shear banding in AISI 1045 steel during high speed machining: Mechanisms of microstructural evolution”, Materials Science and Engineering A, 532: 111–119, (2012)
  11. Arrazola P.J., Villar A., Ugarte D. and Marya S., “Serrated chip prediction in finite element modeling of the chip formation process”, Machining Science and Technology, 11: 367–390, (2007)
  12. Ambati R. and Yuan H., “FEM mesh-dependence in cutting process simulation”, International Journal of Advanced Manufacturing Technology, 53: 313–323, (2010)
  13. Duan C. and Zhang L., “A reliable method for predicting serrated chip formation in high-speed cutting: analysis and experimental verification”, International Journal of Advanced Manufacturing Technology, 64: 1587–1597, (2013)
  14. Aydın M. and Köklü U., “Analysis of flat-end milling forces considering ch