SavedAdd your journal

Journals / Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji / 2017 / Cilt: 5 - Sayı: 1

Effect of Nanoparticles on Carbon Fiber/Epoxy Nanocomposite Laminates Fiber, Matris and Void Volume Fraction

Karbon Fiber/Epoksi Nanokompozit Plakalarda Nanopartikül Katkısının Fiber, Matris ve Boşluk Hacim Oranlarına Etkisi

Mehmet Çağrı TÜZEMEN
Ahmet AVCI
Elmas SALAMCI
Pages
11–19
Publication Date
2022-10-18
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

After burning test, it was found that adding 5% nanoparticles would increase void volume fraction by %221

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this paper, the effect of nanoparticles with different fractions on fiber, matrix and void volume fraction was investigated.
📊
Key Findings & Data:When fraction of nanoparticles increased, both the viscosity of epoxy and agglomeration of nanoparticles in epoxy increased.
💡
Conclusion & Impact:After burning test, it was found that adding 5% nanoparticles would increase void volume fraction by %221
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Abstract

In this paper, the effect of nanoparticles with different fractions on fiber, matrix and void volume fraction was investigated. Vacuum assisted resin transfer molding (VARTM) method was used to manufacture the carbon fiber/epoxy nanocomposite laminates. Before manufacturing, nanoparticles were added to epoxy with different fractions. Manufactured nanocomposites were applied to burning test after they cut into the size referred in standards. When fraction of nanoparticles increased, both the viscosity of epoxy and agglomeration of nanoparticles in epoxy increased. As a result, vacuuming of epoxy under pressure and wetting the fibers get hard while manufacturing. After burning test, it was found that adding 5% nanoparticles would increase void volume fraction by %221

Özet

Bu çalışmada farklı oranlardaki nanopartikül takviyesinin fiber, matris ve boşluk hacim oranlarına etkisi incelenmiştir. Karbon fiber/epoksi nanokompozit plakalar vakum infüzyon yöntemi (VİY) ile üretilmiştir. Üretim öncesinde matris elemanı olan epoksi içerisine farklı oranlarda nanopartikül katılmıştır. Üretilen nanokompozitler standartlarda verilen ölçülerde hazırlandıktan sonra yakma testine tabi tutulmuştur. Nanopartikül katkısı arttıkça hem epoksinin viskozitesi hem de epoksi içerisinde nanopartikül kümelenmeleri artmıştır. Bunun sonucunda üretim esnasında epoksinin basınç altında vakumlanması ve fiberleri ıslatması zorlaşmıştır. Yakma testi sonucunda %5 nanopartikül katkısının boşluk hacim oranını %221 arttırdığı sonucuna ulaşılmıştır

🔖

Cite This Article

TÜZEMEN, M. Ç., AVCI, A., SALAMCI, E. (2022). Effect of Nanoparticles on Carbon Fiber/Epoxy Nanocomposite Laminates Fiber, Matris and Void Volume Fraction. Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji, Cilt: 5 - Sayı: 1, 11–19. https://ajindex.com/articles/522198

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (12)

  1. Zhu, H., Wu, B., Li, D., Zhang, D. and Chen, Y., “Influence of voids on the tensile performance of carbon/epoxy fabric laminates”, Journal of Materials Science & Technology, Cilt 27, No 1, 69-73, 2011
  2. Esnaola, A., Tena, I., Aurrekoetxea, J., Gallego, I. and Ulacia, I., “Effect of fibre volume fraction on energy absorption capabilities of E-glass/polyester automotive crash structures”, Composites Part B: Engineering, Cilt 85, 1-7, 2016
  3. Bodaghi, M., Cristóvão, C., Gomes, R. and Correia, N.C., “Experimental characterization of voids in high fibre volume fraction composites processed by high injection pressure RTM”, Composites Part A: Applied Science and Manufacturing, Cilt 82, 88-99, 2016
  4. Karakuzu, R., Demirgoren, O., Icten, B.M., and Deniz, M.E., “Failure behavior of quasi-isotropic laminates with three-pin loaded holes”, Materials & Design, Cilt 31, No 6, 3029-3032, 2010
  5. Ozen, M., and Sayman, O., “Failure loads of mechanical fastened pinned and bolted composite joints with two serial holes”, Composites Part B: Engineering, Cilt 42, No 2, 264-274, 2011
  6. Bekyarova, E., Thostenson, E.T., Yu, A., Kim, H., Gao, J., Tang, J.,. and Haddon, R.C., “Multiscale carbon nanotube-carbon fiber reinforcement for advanced epoxy composites”, Langmuir, Cilt 23, No 7, 3970-3974 2007
  7. Zhu, J., Imam, A., Crane, R., Lozano, K., Khabashesku, V.N. and Barrera, E.V., “Processing a glass fiber reinforced vinyl ester composite with nanotube enhancement of interlaminar shear strength”, Composites Science and Technology, Cilt 67, No 7, 1509-1517, 2007
  8. Zhou, Y., Pervin, F., Lewis, L. and Jeelani, S., “Fabrication and characterization of carbon/epoxy composites mixed with multi-walled carbon nanotubes”, Materials Science and Engineering: A, Cilt 475, No 1, 157-165, 2008
  9. Parnas, R.S. and Walsh, S.M., “Vacuum‐assisted resin transfer molding model”, Polymer composites, Cilt 26, No 4, 477-485, 2005
  10. Kuentzer, N., Simacek, P., Advani, S.G. and Walsh, S., “Correlation of void distribution to VARTM manufacturing techniques”, Composites Part A: applied science and manufacturing, Cilt 38, No 3, 802-813, 2007
  11. Fiedler, B., Gojny, F.H., Wichmann, M.H., Nolte, M.C. and Schulte, K., “Fundamental aspects of nano-reinforced composites”, Composites science and technology, Cilt 66, No 16, 3115-3125, 2006
  12. Maley, J.A., “An investigation into low-cost manufacturing of carbon epoxy composites and a novel “mouldless” technique using the Vacuum Assist