SavedAdd your journal

Journals / Düzce Üniversitesi Bilim ve Teknoloji Dergisi / 2019 / Cilt: 7 - Sayı: 3

The Effect of Cr and Ni Addition on Mechanical Properties of Plain Carbon Steel

Cr ve Ni İlavesinin Sade Karbonlu Çeliğin Mekanik Özelliklerine Etkisi

Mehmet Akif ERDEN
Hüseyin DEMİRTAŞ
Pages
1217–1223
Publication Date
2022-10-12
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

As a result, it was determined that the added alloying elementsincreased the mechanical properties, but the mechanical properties decreased with the amount of alloyingelements increasing after 1% wt. due to the powder metallurgy process.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, the effect of Cr-Ni addition on the mechanical properties of plain carbon steel was investigated.
📊
Key Findings & Data:Forthis purpose, Cr-Ni (wt. % 0.5-3) was added to the matrix containing 0.5 C with powder metallurgy method.
💡
Conclusion & Impact:As a result, it was determined that the added alloying elementsincreased the mechanical properties, but the mechanical properties decreased with the amount of alloyingelements increasing after 1% wt. due to the powder metallurgy process.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Abstract

In this study, the effect of Cr-Ni addition on the mechanical properties of plain carbon steel was investigated. Forthis purpose, Cr-Ni (wt. % 0.5-3) was added to the matrix containing 0.5 C with powder metallurgy method. Thetensile test, micro hardness measurement and microstructure analysis were performed to investigate the effect ofthe additions on the mechanical properties. As a result, it was determined that the added alloying elementsincreased the mechanical properties, but the mechanical properties decreased with the amount of alloyingelements increasing after 1% wt. due to the powder metallurgy process.

Özet

Bu çalışmada, Cr-Ni ilavesinin sade karbon çeliğinin mekanik özellikleri üzerindeki etkisi araştırılmıştır. Bu amaçla, toz metalürji metoduyla 0.5 C içeren matrise Cr-Ni (ağırlıkça %0,5-3) ilave edilmiştir. Alaşım elementlerinin mekanik özelliklere etkisini araştırmak için çekme testi, mikro sertlik ölçümü ve mikro yapı analizi yapılmıştır. Sonuç olarak, ilave edilen alaşım elementlerinin mekanik özellikleri arttırdığı, ancak toz metalürjisi işleminden dolayı ağ. %1’den sonra artan alaşım elementi miktarı ile mekanik özelliklerin azaldığı tespit edilmiştir.

🔖

Cite This Article

ERDEN, M. A., DEMİRTAŞ, H. (2022). The Effect of Cr and Ni Addition on Mechanical Properties of Plain Carbon Steel. Düzce Üniversitesi Bilim ve Teknoloji Dergisi, Cilt: 7 - Sayı: 3, 1217–1223. https://ajindex.com/articles/494378

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (14)

  1. K. S. Narasimhan, “Sintering of powder mixtures and the growth of ferrous powder metallurgy,” Mater. Chem. Phys., vol. 67, no. 1–3, pp. 56–65, 2001
  2. M. A Erden,, S. Barlak,, B. Adalı,, Ö. Çelikkıran, "Toz Metalurjisi İle Üretilen Nb-V Mikroalaşim Çeliğine Vanadyum İlavesinin Mikroyapi Mekaniksel Özellikleri Üzerine Etkisi". Düzce Üniversitesi Bilim ve Teknoloji Dergisi, c. 6, ss. 629-636, 2018
  3. H. Danninger and C. Gierl, “New alloying systems for ferrous powder metallurgy precision parts,” Sci. Sinter., vol. 40, no. 1, pp. 33–46, 2008
  4. O. Bergman, “Influence of oxygen partial pressure in sintering atmosphere on properties of Cr–Mo prealloyed powder metallurgy steel,” Powder Metall., vol. 50, no. 3, pp. 243–249, 2007
  5. S. Tekeli and A. Güral, "Dry sliding wear behaviour of heat treated iron based powder metallurgy steels with 0.3% Graphite + 2% Ni additions," Materials and Design, vol 28, no.6, pp. 1923–1927, 2007
  6. M. A. Razzak, “Heat treatment and effects of Cr and Ni in low alloy steel,” Bull. Mater. Sci., vol. 34, no. 7, pp. 1439–1445, 2011
  7. M. A. Erden and R. Gunduz, “Effect of Cr Content on Microstructure and Tensile Strength Properties of Cr Added Steel Produced By Powder Metallurgy Method
  8. International Iron & Steel Symposium, pp. 609-611, 2017
  9. S. H. Avner, Introduction to physical metallurgy, 2nd ed, New York, USA: McGraw-Hill, 1974
  10. M. A. Erden, “Investıgatıon Of The Effect Of Nickel Content On Mıcrostructure And Mechanıcal Propertıes Of Non Alloyed Steels Producted By Powder Metallurgy”, GU J Sci Part:C, vol. 4 no. 4, pp. 241-245, 2016
  11. U. Lindstedt, B. Karlsson, and R. Masini, “Influence of porosity on deformation and fatigue behavior of P/M austenitic stainless steel,” Int. J. Powder Metall. (Princeton, New Jersey), vol. 33, pp. 49–61, 1997
  12. H. Danninger, R. Pöttschacher, S. Bradac, A. Šalak, and J. Seyrkammer, “Comparison of Mn, Cr and Mo alloyed sintered steels prepared from elemental powders,” Powder Metall., vol. 48, no. 1, pp. 23–32, 2005
  13. A. Molinari, G. Straffelini, and P. Campestrini, “Influence of microstructure on impact and wear behaviour of sintered Cr and Mo steel,” Powder Metall., vol. 42, no. 3, pp. 235–241, 1999
  14. D. Shanmugasundaram and R. Chandramouli, “Tensile and impact behaviour of sinter-forged Cr, Ni and Mo alloyed powder metallurgy steels,” Mater. Des., vol. 30, no. 9, pp. 3444–3449, 2009.