Journals / Clinical and Experimental Health Sciences / 2019 / Cilt: 9 - Sayı: 4

Evaluation of the Polymerization Depth of Bulk Fill Resin Composites Polymerized by Different Procedures: An In-Vitro Study

Pages
304–309
Publication Date
2019-12-31
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The polymerization with soft start technique may not different from the standard-mode for polymerization depth.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Objective: The aim of this study is to investigate the depth of cure (DOC) of the bulk fill composite samples prepared in different thicknesses with two different modes of light curing device with Vickers hardness tester.Methods: Five different bulk-fill composite materials were used in the present study. 20 sample of 2 mm and 20 sample of 4 mm thick samples were prepared, 10 samples from each group were polymerized for 20 seconds with the standard mode (Mode 1) of the light curing device and 10 samples polymerized with soft-start mode (Mode 2) for 25 seconds (n=10).
📊
Key Findings & Data:The statistical analysis was performed using three-way analysis of variance (ANOVA) and Tukey multiple comparisons (p = 0.05).Results: The hardness ratios of all composites were determined to be over 80%, which is clinically acceptable.
💡
Conclusion & Impact:The polymerization with soft start technique may not different from the standard-mode for polymerization depth.
🔬Design:Research Article
📍Scope:20 sample
⚙️Variables:hardness · polymerization · LED

Abstract

Objective: The aim of this study is to investigate the depth of cure (DOC) of the bulk fill composite samples prepared in different thicknesses with two different modes of light curing device with Vickers hardness tester.Methods: Five different bulk-fill composite materials were used in the present study. 20 sample of 2 mm and 20 sample of 4 mm thick samples were prepared, 10 samples from each group were polymerized for 20 seconds with the standard mode (Mode 1) of the light curing device and 10 samples polymerized with soft-start mode (Mode 2) for 25 seconds (n=10). Hardness measurements were made from the upper and lower surfaces of each sample and the hardness ratio was calculated. The statistical analysis was performed using three-way analysis of variance (ANOVA) and Tukey multiple comparisons (p = 0.05).Results: The hardness ratios of all composites were determined to be over 80%, which is clinically acceptable. There was a statistically significant difference between the DOC levels according to the composites (p <0.05). There was a statistically significant difference according to the thickness (p <0.05). There was no statistically significant difference according to polymerization procedures (p >0.05).Conclusions: The surface hardness ratios of all groups were determined to be over 80%, which is clinically acceptable. The polymerization with soft start technique may not different from the standard-mode for polymerization depth.

🔖

Cite This Article

ÖZYURT, E., KURT, A., YILDIRIM, H. (2019). Evaluation of the Polymerization Depth of Bulk Fill Resin Composites Polymerized by Different Procedures: An In-Vitro Study. Clinical and Experimental Health Sciences, Cilt: 9 - Sayı: 4, 304–309. https://ajindex.com/articles/481597

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (14)

  1. Lindberg A, Peutzfeldt A,van Dijken JW: Effect of power density of curing unit, exposure duration, and light guide distance on composite depth of cure. Clin Oral Investig 2005
  2. 76 2. Pianelli C, Devaux J, Bebelman S, et al: The micro‐Raman spectroscopy, a useful tool to determine the degree of conversion of light‐activated composite resins. Journal of Biomedical Materials Research: An Official Journal of The Society for Biomaterials, The Japanese Society for Biomaterials, and The Australian Society for Biomaterials and the Korean Society for Biomaterials 1999
  3. 681 3. Caughman WF, Caughman GB, Shiflett RA, et al: Correlation of cytotoxicity, filler loading and curing time of dental composites. Biomaterials 1991
  4. 740 4. Ferracane JL, Mitchem JC, Condon JR, et al: Wear and marginal breakdown of composites with various degrees of cure. J Dent Res 1997
  5. 1516 5. Kovarik R,Ergle J: Fracture toughness of posterior composite resins fabricated by incremental layering. The Journal of prosthetic dentistry 1993
  6. 560 6. Knežević A, Tarle Z, Meniga A, et al: Degree of conversion and temperature rise during polymerization of composite resin samples with blue diodes. Journal of Oral Rehabilitation 2001
  7. 591 7. Son SA, Park JK, Seo DG, et al: How light attenuation and filler content affect the microhardness and polymerization shrinkage and translucency of bulk-fill composites? Clin Oral Investig 2017
  8. 565 8. Kramer N, Lohbauer U, García-Godoy F, et al: Light curing of resin-based composites in the LED era. American Journal of Dentistry 2008
  9. 135 9. Martin F: A survey of the efficiency of visible light curing units. Journal of dentistry 1998
  10. 243 10. Abbas G, Fleming GJP, Harrington E, et al: Cuspal movement and microleakage in premolar teeth restored with a packable composite cured in bulk or in increments. Journal of Dentistry 2003
  11. 444 11. Howard B, Wilson ND, Newman SM, et al: Relationships between conversion, temperature and optical properties during composite photopolymerization. Acta Biomater 2010
  12. 2059 12. Bucuta S,Ilie N: Light transmittance and micro-mechanical properties of bulk fill vs. conventional resin based composites. Clin Oral Investig 2014
  13. 2000 13. Czasch P,Ilie N: In vitro comparison of mechanical properties and degree of cure of bulk fill composites. Clin Oral Investig 2013
  14. 235 14. Garoushi S, Vallittu P, Shinya A, et al: Influence of increment thickness on light