SavedAdd your journal

Journals / Bilecik Şeyh Edebali Üniversitesi Fen Bilimleri Dergisi / 2022 / Cilt: 9 - Sayı: 1

Effect of Skeleton Binder Change on Rheological Properties for Ceramic Injection Molding

Seramik Enjeksiyon Kalıplama için İskelet Bağlayıcı Değişiminin Reolojik Özelliklerine Etkisi

Levent URTEKİN
Faik YILAN
İbrahim USLAN
Bedri TUC
Pages
314–323
Publication Date
2022-06-30
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

In the experiment, it was determined that the critical powder volume concentration for both feedstocks was 56%.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Rheological characterization plays an important role in powder injection molding.
📊
Key Findings & Data:In the experiments, polyethylene glycol main binder and polypropylene/polyethylene skeleton without changing the main binder (PEG4000), two different binders (PP / PE) were used as skeleton binders.
💡
Conclusion & Impact:In the experiment, it was determined that the critical powder volume concentration for both feedstocks was 56%.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Besleme Stoku · Seramik Enjeksiyon Kalıplama · Reoloji

Abstract

Rheological characterization plays an important role in powder injection molding. Properties of the selected binders are related directly to the molding, pre-sintering and sintering stages. Besides the residual binding properties of the feedstock, the intended use of the binder (main binder/skeleton binder/lubricant) is also important. In this work, the flow properties of feedstock have been determined with the inclusion of a water-based main binder throughout the injection molding process of a studied ceramic composition. Rheology experiments have been carried out with both capillary and torque rheometers. In the experiments, polyethylene glycol main binder and polypropylene/polyethylene skeleton without changing the main binder (PEG4000), two different binders (PP / PE) were used as skeleton binders. Accordingly, viscosity, shear rate, temperature and melting behavior indexes were determined. In the experiment, it was determined that the critical powder volume concentration for both feedstocks was 56%.

Özet

Toz enjeksiyon kalıplama prosesi için reoloji çalışması önemli bir yere sahiptir. Seçilen bağlayıcıların özellikleri; kalıplama, ön sinterleme ve sinterleme aşamalarını doğrudan ilgilendirmektedir. Besleme stokuna eklenen bağlayıcı özelliklerinin yanı sıra bağlayıcıların (ana bağlayıcı/iskelet bağlayıcı/yağlayıcı) kullanım amacı da önemlidir. Bu çalışmada seramik enjeksiyon kalıplama süreci için su bazlı ana bağlayıcı kullanılarak akış özellikleri (reoloji) belirlenmiştir. Reoloji deneyleri hem kılcal hemde tork reometreleri ile gerçekleştirilmiştir. Deneylerde; polietilen glikol ana bağlayıcı ve polipropilen/polietilen iskelet bağlayıcı kullanılarak farklı karışım oranlarında hazırlanan besleme stokları ile gerçekleştirilmiştir. Ana bağlayıcı değiştirilmeden (PEG4000), iskelet bağlayıcı olarak ise iki farklı (PP/PE) bağlayıcı kullanılmıştır. Buna bağlı olarak viskozite, kayma hızı, sıcaklık ve erime davranış indeksleri tespit edilmiştir. Deney sonucunda her iki besleme stoku için kritik toz yüklemesinin hacimce %56 oranında olduğu tespit edilmiştir.

🔖

Cite This Article

URTEKİN, L., YILAN, F., USLAN, İ., TUC, B. (2022). Effect of Skeleton Binder Change on Rheological Properties for Ceramic Injection Molding. Bilecik Şeyh Edebali Üniversitesi Fen Bilimleri Dergisi, Cilt: 9 - Sayı: 1, 314–323. https://ajindex.com/articles/475494

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (14)

  1. German, R.M. & Bose, A. (1997). Injection Molding of Metals and Ceramics Metal Powder Industries Federation, Princeton 10-250.
  2. P. Thomas-Vielma, A. Cervera, B. & Levenfeld, A. (2008). Várez Journal of the European Ceramic Society, 28, 763-771.
  3. Hanemann, T., & Weber, O. (2014). Polymethylmethacrylate/polyethyleneglycol-based partially water-soluble binder system for micro ceramic injection moulding, Microsystem Technology, 20, 51–58.
  4. Subaşı M., Yılmaz O., Same, K., Safarian A., & Karataş Ç., (2020). Toz Enjeksiyon Kalıplamada 316 L Besleme Stokunun Çekme Yüzdesinin Yapay Sinir Ağları İle Tahmin Edilmesi, El-Cezeri Journal of Science and Engineering, 7 (3):1063-1073.
  5. German, R.M. (1990).
  6. Toz Enjeksiyon Kalıplama MPIF, ABD. 1-225. Weber O, & Hanemann T, (2011). Molding Compounds on partially water-soluble organic binder for production of complex shaped ceramic micro parts, In Proceedings of the 18th International Conference on Composite Materials, Jeju Island, South Korea. Bleyan D, Svoboda P, & Hausnerova B, (2015). Specific interactions of low molecular weight analogues of carnaubawax and polyethyleneglycol binders of ceramic injection moulding feedstocks, Ceram. Int., 41: 3975–3982.
  7. D. Claudel, M. Sahli, T. Barriere, & J.C. Gelin. (2017). Influence of particle-size distribution and temperature on the rheological properties of highly concentrated Inconel feedstock alloy 718. Powder Technol., 322, 273-289.
  8. Park MS, Kim JK, Ahn S, & Sung HJ, (2001). Water-soluble binder of cellulose acetate butyrate/poly (ethylene glycol) blend for powder injection moulding, J. Mater. Sci., 36:5531–5536.
  9. Hwang BJ, Lin ST, Sarma LS, & Cheng MY., (2003).
  10. Feedstock for Injection Molding, US, 10/170464. C.I. Chung, B.O. Rhee, M.Y. Cao,& C.X. Liu (1989). Requirements of binder for powder injection molding Advances in Powder Metallurgy Proceeding, Powder Metallurgy Conference Exhibition, MPIF, Princeton, NJ, USA, 67-78.
  11. Gao Y, Huang K, Fan Z, & Xie Z, (2007). Injection molding of zirconia ceramics using watersoluble binders, Key Eng. Mater., 336–338:1017–1020.
  12. J.M. Contreras, A. Jiménez-Morales, & J.M. Torralba (2010). Experimental and theoretical methods for optimal solid loading calculation in MIM feedstocks fabricated from powders with different particle characteristics. Powder Metall, 53 (1). 34-40.
  13. R. Supati, N.H. Loh, K.A. Khor, & S.B. Tor (2000) Mixing and characterization of feedstock for powder injection molding. Mater Lett, 46. 109-114.
  14. Karatas C, Kocer A, Unal HI, & Sari