SavedAdd your journal

Journals / Pamukkale Üniversitesi Mühendislik Bilimleri Dergisi / 2019 / Cilt: 25 - Sayı: 4

Investigation of air jet impingement drying with forced convection of moist things

Nemli nesnelerin zorlanmış taşınım ile hava jeti çarpmalı kurutulmasının incelenmesi

Koray KARABULUT
Doğan Engin ALNAK
Pages
387–395
Publication Date
2019-08-28
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

As locality, drying of jet was appeared to be most powerful close to the stillness point on the front face of the things.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this work, the effect of drying with jet of air of two dissimilar moist thing geometries with whole and straight semi-circular on the enhancement of heat transfer and decrement of moisture amount was numerically examined.
📊
Key Findings & Data:A method of finite volume was used to figure out the conservation equations by employing software program of ANSYS Fluent 17.0.
💡
Conclusion & Impact:As locality, drying of jet was appeared to be most powerful close to the stillness point on the front face of the things.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Zorlanmış taşınım · Nem transferi · Sayısal analiz

Abstract

In this work, the effect of drying with jet of air of two dissimilar moist thing geometries with whole and straight semi-circular on the enhancement of heat transfer and decrement of moisture amount was numerically examined. The drying jet had a laminar flow characteristic and two-dimensional jet situated at a fixed jet space from the moist thing. The moist thing diameter, jet space from the moist thing and height of jet initial were taken as stable in whole situations. Streamlines and isotherms were visualized around the things for dissimilar velocities of jet. A method of finite volume was used to figure out the conservation equations by employing software program of ANSYS Fluent 17.0. Computations were conducted for dissimilar Re, so, Re = 100, 200 and 300. It was obtained well accord with scalar and empirical output found in the reference. The results illustrated that the whole circular moist thing had greater good heat and moisture transfer performance than that of the straight semi-circular moist thing. Furthermore, it was seen that an increase of Re number had an affirmative effect on heat and moisture transfer. As locality, drying of jet was appeared to be most powerful close to the stillness point on the front face of the things.

Özet

Bu çalışmada, tam ve düz yarı dairesel olmak üzere iki farklı nemli nesne geometrisinin hava jeti ile kurutulmasının ısı transferi artışı ve nem miktarındaki azalışı üzerindeki etkisi sayısal olarak incelenmiştir. Jet kurutması, nemli nesneden sabit bir jet uzaklığında konumlandırılmış, laminer ve iki boyutludur. Tüm durumlarda, nemli nesnenin çapı, nemli nesneden olan jet uzaklığı ve jet giriş yüksekliği sabit alınmıştır. Farklı jet hızları için nesnelerin etrafındaki akım çizgileri ve eş sıcaklık eğrileri görselleştirilmiştir. Korunum denklemlerini çözmek için sonlu hacim yöntemi olan ANSYS Fluent 17.0 bilgisayar programı kullanılmıştır. Hesaplamalar, Re=100, 200 ve 300 olarak farklı Reynolds sayıları için gerçekleştirilmiştir. Çalışmanın, literatürde var olan sayısal ve deneysel çalışmayla iyi bir uyum içinde olduğu bulunmuştur. Sonuçlar, tam dairesel nemli nesnenin düz yarı dairesel nemli nesneden daha iyi ısı ve nem transferi performansına sahip olduğunu göstermiştir. Ayrıca, Reynolds sayısının artışının ısı ve nem transferi üzerinde olumlu bir etkiye sahip olduğu görülmüştür. Yerel olarak, jet kurutmanın nesnelerin ön taraflarındaki durma noktasına yakın daha etkili oldukları bulunmuştur.

🔖

Cite This Article

KARABULUT, K., ALNAK, D. E. (2019). Investigation of air jet impingement drying with forced convection of moist things. Pamukkale Üniversitesi Mühendislik Bilimleri Dergisi, Cilt: 25 - Sayı: 4, 387–395. https://ajindex.com/articles/42186

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (15)

  1. Martin H. Heat and Mass Transfer Between Impinging Gas Jets and Solid Surfaces, Advances in Heat Transfer, New York, USA, Academic Press, 1977.
  2. Lee HG, Yoon HS, Ha MY. “A numerical investigation on the fluid flow and heat transfer in the confined impinging slot jet in the low reynolds number region for different channel heights”. International Journal of Heat and Mass Transfer, 51(15-16), 4055-4068, 2008.
  3. Tawfek AA. “Heat transfer studies of the oblique ımpingement of round jets upon a curved surface”. Heat and Mass Transfer, 38, 467-475, 2002.
  4. Olsson EEM, Ahrne LM, Tragardh AC. “Flow and heat transfer from multiple slot air jets impinging on circular cylinders”. Journal of Food Engineering, 67(3), 273-280, 2005.
  5. Olsson EEM, Ahrne LM, Tragardh AC. “Heat transfer from a slot air jet impinging on a circular cylinder”. Journal of Food Engineering, 63, 393-401, 2004.
  6. Rahman MM, Hernandez CF, Lallave JC. “Free liquid jet impingement from a slot nozzle to a curved plate”. Numerical Heat Transfer Part A, 57(11), 799-821, 2010.
  7. Teamah MA, Khairat MM. “Heat transfer due to impinging double free circular jets”. Alexandria Engineering Journal, 54(3), 281-293, 2015.
  8. Hosain Md L, Fdhila RB, Daneryd A. “Heat transfer by liquid jets impinging on a hot flat surface”. Applied Energy, 164, 934-943, 2016.
  9. McDaniel CS, Webb BW. “Slot jet impingement heat transfer from circular cylinders”. International Journal of Heat and Mass Transfer, 43(11), 1975-1985, 2000.
  10. Eren H, Yeşilata B, Celik N. “Nonlinear flow and heat transfer dynamics of impinging jets onto slightly-curved surfaces”. Applied Thermal Engineering, 27(14-15), 2600-2608, 2007.
  11. Frost SA, Jambunathan K, Whitney CF, Ball SJ. “Heat transfer from a flat plate to a turbulent axisymmetric impinging jet”. Proceeding of the Institution of Mechanical Engineers, Part C, 211(2), 167-172, 1997.
  12. Chan TL, Leung CW, Jambunathan K, Frost SA, Zhou Y, Liu MH. “Heat transfer characteristics of a slot jet impinging on a semi-circular convex surface”. International Journal of Heat and Mass Transfer, 45(5), 993-1006, 2002.
  13. Varol Y, Alnak DE, Oztop HF, Al-Salem K. “Numerical analysis of heat transfer due to slot jets impingement onto two cylinders with different diameters”. International Communications in Heat and Mass Transfer, 39(5), 726-735, 2012.
  14. Gori F, Petracci I, Tedesco V. “Cooling of two smooth cylinders in row by a slot jet of air with low turbulence”. Applied Thermal Engineering, 27(14-15), 2415-2425, 2007.
  15. Chan TL, Zhou Y, Liu