SavedAdd your journal

Journals / Tekstil ve Mühendis / 2011 / Cilt: 18 - Sayı: 84

Investigation of process parameters effecting the single surface coating applied by roll-on knife method

Silindir üstü bıçak yöntemi kullanılarak yapılan tek yüz kaplama işlemini etkileyen proses parametrelerinin incelenmesi

Onur BALCI
Özlem ÇAYLAN
Nilay CAN
Pages
15–22
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

In addition, in order to determine the usability of the specimens, physical evaluations namely tensile strength, tear strength, weight, and bending strength were achieved.As a result, it was found that the binder type and coating thickness were effective parameters.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, it was statistically aimed to determine the penetration ratio of the coating paste to the back side of the fabric and to investigate the coating process parameters, which affect the quantity of this penetration, for woven fabrics manufactured by single face coating process.
📊
Key Findings & Data:The CIELab values and water repellency performance were determined as the criteria to decide the penetration ratio of the paste to the back side of the sample fabrics.
💡
Conclusion & Impact:In addition, in order to determine the usability of the specimens, physical evaluations namely tensile strength, tear strength, weight, and bending strength were achieved.As a result, it was found that the binder type and coating thickness were effective parameters.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Abstract

In this study, it was statistically aimed to determine the penetration ratio of the coating paste to the back side of the fabric and to investigate the coating process parameters, which affect the quantity of this penetration, for woven fabrics manufactured by single face coating process. The binder type, coating thickness, angle of the coating knife and type of the softeners used in the paste were defined as process variables and the roll on knife coating was chosen as the application method. The CIELab values and water repellency performance were determined as the criteria to decide the penetration ratio of the paste to the back side of the sample fabrics. In addition, in order to determine the usability of the specimens, physical evaluations namely tensile strength, tear strength, weight, and bending strength were achieved.As a result, it was found that the binder type and coating thickness were effective parameters.

Özet

Çalışmada tek yüz kaplama prosesi ile işlem görmüş dokuma kumaşlarda, kaplama patının kumaş arka yüzüne geçme oranının ve bu geçme miktarını etkileyen proses parametrelerinin istatistiksel olarak incelenmesi hedeflenmiştir. Proses parametresi olarak binder tipi, kaplama kalınlığı, bıçak açısı ve pat içerisindeki yumuşatıcı tipi seçilmiştir. Metot olarak silindir üstü bıçak yöntemi seçilmiştir. Arka yüze geçme oranının karar verilmesinde CIELab sonuçları ve su iticilik değerleri kriter olarak belirlenmiştir. Bunun yanında, kaplamalı ürünün kullanılabilirliğinin belirlenebilmesi için deneysel çalışmada bazı fiziksel (kopma mukavemeti, yırtılma mukavemeti, gramaj, eğilme dayanımı) testlere de yer verilmiştir. Sonuçlar incelendiğinde, kullanılan binder tipinin ve kaplama kalınlığının kumaşın arka yüzüne geçme oranı için etkili parametreler olduğu görülmüştür.

🔖

Cite This Article

BALCI, O., ÇAYLAN, Ö., CAN, N. (2011). Investigation of process parameters effecting the single surface coating applied by roll-on knife method. Tekstil ve Mühendis, Cilt: 18 - Sayı: 84, 15–22. https://ajindex.com/articles/366360

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (3)

  1. Bulut, Y., Sülar, V., (2009), Kaplama veya laminasyon teknikleri ile üretilen kumaşların genel özellikleri ve performans testleri, Tekstil ve Mühendis, 15(70-71), 5-16
  2. Asker, Ğ., Balcı, O., Topçal, F., (2011), Kaplama ve emdirme aplikasyon yöntemlerinin kombinasyonu ile üretilen melez kumaşların performans özelliklerinin belirlenmesi, Tekstil ve Mühendis, 18(82), 6-18
  3. Yesilalan, H., E., Warner, S., B., Laoulache, R., (2010), Penetration of blade-applied viscous coatings into yarns in a woven ric, Textile Research Journal, 80(18), 1930-1941. 4.Mukhopadhyay, A., Midha, V., K., (2008), A review on igning the waterproof breathable fabrics part ıı: construction I suitability of breathable fabrics for different uses, Journal of ustrial Textiles, 38(1), 17-41, 5.Padleckiene, I., Petrulis, D., (2009), Effect of abrasion on the permeability & mass loss of breathable-coated fabrics, res&Textiles in Eastern Europe, 17(2-73), 50-54. 6.Dembicky J., (2010), Simulation of the coating process, res&Textiles in Eastern Europe, 18(1-78), 79-83. 7.Struszczyk, M., H., Brzoza-Malczewska, K., Szalczynska, M., 07), A nonwovens coated by chitosan with potential anti-robial behaviour-preliminary results, Fibres& Textiles in tern Europe, January/December, 15(5-6), 64-65. 8.Özyüzer, L., Meriç, Z., Selamet, Y., Kutlu, B., Cireli, A., (2010), natıssal saçtırma sistemi ile metal kaplanan polipropilen rin antistatikve antibakteriyel özellikleri, Tekstil ve Mühendis, 78), 1-5. 9.Tao, X., Koncar, V., Dufour, C., Onar, N., Akşit, A., (2010), Soljel yöntemi ile düşük sıcaklıkta polietilen tereftalat dokusuz yüzey kumaşların indiyum çinko oksit çözeltileri ile kaplanması, Tekstil Mühendis, 17 (79), 2-6. 10.Test Standardı, AATCC Test Method 22-2010 Water Repellency ly Test 11.Test Standardı, EN ISO 13934-2, Textiles -Tensileproperties of ics — Part 2: Determination of maximum force using the strip hod 12.Test Standardı, EN ISO 13937-1, Textiles — Tear properties of ics — Part 1: Determination of tear force using ballistic iulum method (Elmendorf) 13.Test Standardı, TS 251, Birim uzunluk ve birim alan kütlesinin İİ 14.Test Standardı, ASTM D4032 - 08 Standard test method far tess of fabric by the circular bendprocedure