SavedAdd your journal

Journals / Çukurova Üniversitesi Mühendislik-Mimarlik Fakültesi Dergisi / 2006 / Cilt: 21 - Sayı: 1

Paslanmaz çeliklerde kaynak işleminin mikroyapıya etkileri

Effect of welding process on microstructure of stainless steels

UĞUR EŞME
Pages
25–31
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

In this study the effect welding process on the microstructural properties of the stainless steels were established.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:The stainless properties of stainless steels are primarily due to the presence of chromium (Cr) in quantities greater than roughly 12 weight percent.
📊
Key Findings & Data:This level of chromium is the minimum level of chromium to ensure a continuous stable layer of protective chromium-rich oxide forms on the surface.
💡
Conclusion & Impact:In this study the effect welding process on the microstructural properties of the stainless steels were established.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Abstract

The stainless properties of stainless steels are primarily due to the presence of chromium (Cr) in quantities greater than roughly 12 weight percent. This level of chromium is the minimum level of chromium to ensure a continuous stable layer of protective chromium-rich oxide forms on the surface. The ability to form chromium oxide in the weld region must be maintained to ensure stainless properties of the weld region after welding. In this study the effect welding process on the microstructural properties of the stainless steels were established.

Özet

Paslanmaz çelikler; içerisinde en az ağırlıkça % 12 oranında krom (Cr) içeren demir esaslı alaşımlar olarak tanımlanırlar. Olması gereken bu minimum krom seviyesi malzeme yüzeyinde kromca zengin koruyucu oksit tabakasının oluşumunu sağlar. Kaynak sonrası malzemenin paslanmazlık özelliğinin sürdürülebilmesi bu krom oksit tabakasının korunmasına bağlıdır. Bu çalışmada kaynak işleminin paslanmaz çeliğin mikroyapısı üzerindeki etkileri açıklanmıştır.

🔖

Cite This Article

EŞME, U. (2006). Paslanmaz çeliklerde kaynak işleminin mikroyapıya etkileri. Çukurova Üniversitesi Mühendislik-Mimarlik Fakültesi Dergisi, Cilt: 21 - Sayı: 1, 25–31. https://ajindex.com/articles/350640

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (2)

  1. Kou,S., "Welding Metallurgy Second Edition", John Wiley & Sons, 1987. 2.Key,J.F., Chan,J.W., "Process Variable Influence on Arc Temperature Distribution", Welding Journal, 62, 179-184, 1999. 3.AWS, "Heat Flow in Welding", Welding Handbook, Volume 3, 1976. 4.ASM,"Metals Handbook", Tenth Edition,
  2. ASM International Handbook Committee, Materials Park Vol. 1, 2002. 5.Wahab,A.M. and Sakano,M. "Experimental Study Corrosion Fatigue Behaviour of Welded Steel Structures", Journal of Materials Processing Technology, 118:117-122,2001. 6.Yuri, T. and et al, "Effect of Welding Structure and Delta-Ferrite on Fatigue Properties for TIG Welded Austenitic Stainless Steels at Cryogenic Temperatures",Cryogenics, 40:251-259, 2000. 7.Zhu,K.X. and Chao,J. Y., "Effects of Temperature-Dependent Material Properties on Welding Simulation", Computers and Structures, 80:967-976, 2002. 8.Tsai,N., "Heat Distribution and Weld Bead Geometry in Arc Welding", Ph.D. Thesis, M.I.T, 1983. 9.Timofeev,T.B. and et al, "Facture Toughness of Austenitic Welded Joints", International Journal of Pressure Vessels and Piping, 76:393-400, 1999. 10.Stout,R.D., "Weldability of Steels, Welding Research Council, 4th edition",USA, 1987. 11.Poorhaydari,B.K. and et al, Estimation of Cooling rate in the Welding of Plates with Intermediate Thickness, Welding journal, October, 149-155, 2005. 12.Norman,F.A., Drazhner,V. and Prangnell,B.P., Effect of Welding Parameters on- the Solidification Microstructure of Autogenous TIG Welds in an Al-Cu-Mg-Mn Alloy,Materials Science and Engineering, (A259): 53-64, 1999. 13.Murugan,S. and et al, "Temperature Distribution and Residual Stresses due to Multipass Welding in type 304 Stainless Steel and Low Carbon Steel Weld Pads", International Journal of Pressure Vessels and Piping, 78(4): 307-317, 2001. 14.Mohandas, T. and et al,"A Comparative Evaluation of Gas Tungsten and Shielded Metal Arc Welds of a Ferritic Stainless Steel", Journal of Materials Processing Technology, 94:133-140, 1999. 15.Lothongkum,G.,Viyanit,E. and Bhandhubanyong,P., "Study on the Effects of Poled TIG Welding Parameters on Delta-Ferrite Content, Shape Factor and Bead Quality in Orbital Welding of AISI 316L Stainless Steel Plate", 110:233-238, 2001.