SavedAdd your journal

Journals / Çukurova Üniversitesi Mühendislik-Mimarlik Fakültesi Dergisi / 2004 / Cilt: 19 - Sayı: 2

Kanat borulu bir ısı eşanjörü içerisinde horseshoe vortex oluşumu ve gelişimi

Horseshoe vortex formation and evolution in a single row plate fin and tube heat exchanger

Azize AKKOCA
N. Adil ÖZTÜRK
Beşir ŞAHİN
Hüseyin AKILLI
Pages
15–25
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Experimental results show that complex 3-D flow characteristics in the heat exchanger flow passage strongly correlate with the heat transfer performance of these types of heat exchangers.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In the present investigation, the attention is focused on a compact, extended surface, cross-flow, single phase, two-fluid heat exchanger with continuous plate fins attached perpendicularly to the outside of the circular tube.
📊
Key Findings & Data:Laminar, transitional and turbulence characteristics of the flow for the plate fin and tube heat exchanger having non-dimensional fin spacing to cylinder diameter ratio of S = 0.365 are investigated in detail at Re = 600, 1500, and 4000.
💡
Conclusion & Impact:Experimental results show that complex 3-D flow characteristics in the heat exchanger flow passage strongly correlate with the heat transfer performance of these types of heat exchangers.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Abstract

In the present investigation, the attention is focused on a compact, extended surface, cross-flow, single phase, two-fluid heat exchanger with continuous plate fins attached perpendicularly to the outside of the circular tube. Laminar, transitional and turbulence characteristics of the flow for the plate fin and tube heat exchanger having non-dimensional fin spacing to cylinder diameter ratio of S = 0.365 are investigated in detail at Re = 600, 1500, and 4000. Experimental results show that complex 3-D flow characteristics in the heat exchanger flow passage strongly correlate with the heat transfer performance of these types of heat exchangers. It is also shown that formation and evolution of horseshoe vortex system strongly depend on the Reynolds number.

Özet

Bu çalışmada; çift akışkanlı, karşı-akışlı, tek fazlı, dairesel boru ve borulara dik olarak yerleştirilen ve sürekli kanatçıklardan oluşan bir kompakt ısı eşanjöründe, laminar, türbülansa geçiş ve türbülanslı akış karakteristikleri, Re = 600, 7500, 4000 ve boyutsuz kanat açıklığı-silindir çapı oranı S = 0.365 için detaylı olarak araştırılmıştır. Elde edilen deneysel sonuçlardan, ısı esanjörü akım pasajında meydana gelen kompleks ve 3-boyutlu akış özellikleri ile ısı eşanjörünün ısı transfer performansı arasında sıkı bir ilişki olduğu ve Reynolds sayısının oldukça etkili olduğu gözlenmiştir.

🔖

Cite This Article

AKKOCA, A., ÖZTÜRK, N. A., ŞAHİN, B., AKILLI, H. (2004). Kanat borulu bir ısı eşanjörü içerisinde horseshoe vortex oluşumu ve gelişimi. Çukurova Üniversitesi Mühendislik-Mimarlik Fakültesi Dergisi, Cilt: 19 - Sayı: 2, 15–25. https://ajindex.com/articles/350474

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (14)

  1. Kuppan,T., “Heat Exchanger Design Handbook”, Marcell Dekker, Inc., Basel, ISBN: 0-8247-9787-6, 1119 p, New York, 2000
  2. Saboya,F.E.M., Sparrow,”E.M., Local and Average Transfer Coefficients for One Row Plate Fin and Tube Heat Exchanger Configurations”, J. Heat Transfer, Trans. ASME., August: 265-27, 1974
  3. Goldstein,L.G., Sparrow,E.M., “Experiments on the Transfer Characteristics of a Corrugated Fin and Tube Heat Exchanger Configuration”, J. Heat Transfer, Trans ASME, February: 26-32, 1976
  4. Seshimo,Y., Fujii,M., “An Experimental Study on the Performance of Plate fin and Tube Heat Exchangers at Low Reynolds Numbers”, ASME/JSME Thermal Engineering Proceedings, (4): 449-454, 1991
  5. Kim,J.Y., Song,T.H., “Microscopic Phenomenaand Macroscopic Evaluation of Heat Transfer From Plate Fins/Circular tube Assembly Using Naphthalene Sublimation Technique”, International Journal of Heat and Mass Transfer, 45: 3397-3404, 2002
  6. Jang,J.Y., Wu,M.C., Chang,W.J., “Numerical and Experimental Studies of Three- Dimensional Plate Fin and Tube Heat Exchangers”, International Journal of Heat and Mass Transfer, 39(14): 3057-3066, 1996
  7. Wang,C.C., Fu,W.L., Chang,C.T., “Heat Transfer and Friction Characteristics of Typical Wavy Fin-and-tube Heat Exchangers”, Experimental Thermal and Fluid Science, 14: 174-186, 1997
  8. Madi,M.A., Johns,R.A., Heikal,M.R., “Performance Characteristics Correlation for Round Tube and Plate Finned Heat Exchangers”, Int. J. Refrigeration, 21(7):507-517, 1998
  9. Wang,C.C., Tsai,Y.M., Lu,D.C., “Comprehensive Study of Convex-Louver and Wavy Fin- and Tube Heat Exchangers”, Journal of Thermophysics and Heat transfer, 12(3): 423-430, 1998
  10. Wang,C.C., Chang,J.Y., Chiou,N.F., “Effects of Waffle Height on the Air Side Performance of Wavy fin- and- Tube Heat Exchangers”, Heat transfer Engineering, 20(3): 45-56, 1999
  11. Yan,W.M., Sheen,P.J., “Heat Transfer and Friction Characteristics of Fin and Tube Heat Exchangers”, Int. J. Heat Mass Transfer, 43: 1651-1659, 2000
  12. Lozza,G., Merlo,U., “An Experimental Investigation of Heat Transfer and Friction Losses of Interrupted and Wavy Fins for Fin-and-Tube Heat Exchangers”, Int.J. Refrigeration, 24: 409-416, 2001
  13. Critoph,R.E., Holland,M.K., Fisher,M., “Comparison of Steady State and Trasnsient Methods for Measurement of Local Heat Transfer in Plate fin- Tube HeatExchangers Using Liquid Cristal Thermography With Radiant Heating”, Int. J. Heat and Mass Transfer, 42: 1-12, 1999
  14. Wierbowzski,M