Journals / Politeknik Dergisi / 2002 / Cilt: 4 - Sayı: 0

Pre-determination of the machining parameters of MA 956 superalloy material by wire EDM

MA 956 süperalaşım malzemesi için tel erozyonda işleme parametrelerinin ön tayini

Pages
7–14
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The appropriate Wire EDM machining conditions of MA 956 superalloy is determined and graphical results are obtained according to the surface roughness and machining speeed.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In the manufacturing industry, superalloy materials is widely preferred to produce machine elements which have to keep their functions in working at high temperatures.
📊
Key Findings & Data:For Wire EDM, because the selection of machining conditions does not contain superalloy materials, in this study, is the effect of the main parameters for MA 956 superalloy in the wire-electro discharge machining investigated.
💡
Conclusion & Impact:The appropriate Wire EDM machining conditions of MA 956 superalloy is determined and graphical results are obtained according to the surface roughness and machining speeed.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Abstract

In the manufacturing industry, superalloy materials is widely preferred to produce machine elements which have to keep their functions in working at high temperatures. In the die and mold making, it is yet unknown what behavioral results of these materials are when machining in Wire EDM, because of their good toughness and wear resisting properties under high temperatures. For Wire EDM, because the selection of machining conditions does not contain superalloy materials, in this study, is the effect of the main parameters for MA 956 superalloy in the wire-electro discharge machining investigated. The appropriate Wire EDM machining conditions of MA 956 superalloy is determined and graphical results are obtained according to the surface roughness and machining speeed.

Özet

Süperalaşım malzemeler, imalat endüstrisinin yüksek sıcaklıklarda fonksiyonunu kaybetmeden çalışması gereken makine elemanlarının imalatında yaygın olarak tercih edilmektedir. Kalıpçılık sektöründe plastik enjeksiyon ve dövme kalıplarında, yüksek ısı altında tokluk ve aşınma özelliklerinde gözlenen iyileşmeden dolayı tercih edilen bu malzemelerin, tel erozyon tezgahlarında işlenmeye karşı vereceği cevap bilinmemektedir. Tel erozyon tezgahları için önerilen işleme şartları bu ve benzeri özel malzemeleri içermediğinden, MA 956: Süperalaşım malzemesinin kıvılcımla aşındırma altındaki davranışı incelenmiştir. Tel erozyon için gerekli işleme şartları deneysel olarak kararlaştırılmaya çalışılmış, yüzey pürüzlülüğü ve işleme hızı kriterlerine göre elde edilen grafikler yorumlanmıştır.

🔖

Cite This Article

ÖZDEMİR, A., TÜRKER, M., KARATAŞ, Ç., GÜLLÜ, A. K. (2002). Pre-determination of the machining parameters of MA 956 superalloy material by wire EDM. Politeknik Dergisi, Cilt: 4 - Sayı: 0, 7–14. https://ajindex.com/articles/306921

References (14)

  1. Soni, J.S., Chakraverti, G., “Experimental Investigation On Migration Of Material During EDM of Die Steel (T215 Cr12)”, Journal of Materials Processing Technology, Vol. 56, pp 439 – 451, 1996
  2. Liao, Y.S., Huang, J.T., Su, H.C., “A Study On The Machining – parameters of Electrical Discharge Machining”, Journal of Materials Processing Technology, Vol. 71, pp 487 – 493, 1997
  3. Özdur, Z., “Tel Elektro Erozyonda İşleme Parametrelerinin Parçanın Yüzey Pürüzlülüğüne, Ölçü Tamlığına ve İşleme Hızına Etkisinin Araştırılması”, Gazi Üniversitesi, Fen Bilimleri Enstitüsü, Y. Lisans Tezi, 1999
  4. Sims, C.T., 6 th Plansee Seminar Book, 1968
  5. Gessinger, G.H., Powder Metallurgy of Superalloys, Butterworths, 1984
  6. Elliott, I.C., and Hack, G.A., MA Alloys For Aerospace Applications, Proc. Conf. On Structural Application of Mechanical Alloying, Ed. By Froes, J.J., and de Barbadillo, J.J., Myrtle Beach, pp.15 - 23, South Carolina, 1990
  7. Li, X.Q., Wong, Y.S., Nee, A.Y.C., “Tool Wear And Chatter Detection Using The Cohorence Function of Two Crossed Accelerations”, International Journal of Machine Tools and Manufacture, Vol. 37, No. 4, pp. 425 – 435, April 1997
  8. Felloni, L., Gatto, A., Ippolito, R., Iuliano, L., “On the Performance of A CrN Coated SiC Whiskers Reinforced Ceramic Tool High Speed Machining of Ni – base Super Alloys”, Industrial Ceramics, Vol. 17, pp. 153–157, September – December 1997
  9. Choudhury, I.A., El-Baradie, M.A., “Machinability of Nickel – Base Superalloys: A General Review”, Journal of Materials Processing Technology, Vol. 77, pp. 278 – 284, May 1998
  10. Darowicki, K., Krakowiak, S., “Durability Evalution of Ni-Cr-Mo Super Alloys in A Simulated Scrubbed Flue Gas Environment”, Anti –corrosion Methods and Materials, Vol. 46, No. 1, pp 19 – 22, 1999
  11. Chow, H.M., Yan, B.H., Huang, F.Y., “Micro Slit Machining Using Electro-discharge Machining With a Modified Rotary Disk Electrode (RDE)”, Jour. Of Materials Processing Technology, Vol. 91, pp. 161-166, 1999
  12. Murphy, K.D., Lin, Z., “The İnfluence of Spatially Nonuniform Temperature Fields on The Vibration And Stability Characteristics Of EDM Wires”, Int. Journal Of Mechanical Sciences, Vol. 42, pp. 1369-1390, 2000
  13. Watanabe, H., Stato, T., Suzuki, I., “WEDM Monitoring With A Statistical Pulse Classification Method”, Ann. CIRP 39, No. 1, pp. 175-178, 1990
  14. Gatto, A., Iuliano, L., “Cutting Mechanisms And Surface Features Of WED Machined Metal Matrix Composites”, Journal Of