Journals / Niğde Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi / 2017 / Cilt: 6 - Sayı: 2

EFFECT OF ANISOTROPY DETERMINATION METHODS ON FORMING LIMIT CURVE PREDICTION OF 304L STAINLESS STEEL

304L PASLANMAZ ÇELİĞİN ŞEKİLLENDİRME SINIR DİYAGRAMININ BELİRLENMESİNDE ANİZOTROPİ BELİRLEME METODUNUN ETKİSİ

Pages
737–751
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The models are evaluated for different anisotropy determination approaches and the predicted results have been compared with the experimental forming limit diagram.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In recent years, numerous researchers have focused on the determination of the formability limits of the sheet materials experimentally and numerically.
📊
Key Findings & Data:In the literature, most of the developed model results strongly depend on yield functions used and their parameters which reflect the materials’ anisotropic behaviors.
💡
Conclusion & Impact:The models are evaluated for different anisotropy determination approaches and the predicted results have been compared with the experimental forming limit diagram.
🔬Design:Modeling & Simulation
📍Scope:2003 Verileri
⚙️Variables:304L · şekillendirme sınır diyagramı · BBC ailesi

Abstract

In recent years, numerous researchers have focused on the determination of the formability limits of the sheet materials experimentally and numerically. Due to some troubles encountered during the experimental studies, the modeling of the formability characteristics of the materials via simple experiments like tensile tests is the main issue for the most researchers. In the literature, most of the developed model results strongly depend on yield functions used and their parameters which reflect the materials’ anisotropic behaviors. In this study, the capability of BBC family yield functions (BBC2000, 2003, 2005 and 2008) are investigated to construct the forming limit diagram of 304L stainless steel by using the Marciniak-Kuczynski instability model. The models are evaluated for different anisotropy determination approaches and the predicted results have been compared with the experimental forming limit diagram.

Özet

Son yıllarda birçok araştırmacı sac malzemelerin şekillendirme sınırlarının deneysel ve nümerik olarak belirlenmesi üzerine odaklanmışlardır. Deneysel çalışmalar esnasında birçok zorluklarla karşılaşılmasından ötürü, birçok araştırmacı için malzemelerin şekillendirme karakteristiklerini çekme deneyi gibi basit deneylerden modellenerek elde edilmesi temel bir mesele haline gelmiştir. Literatürde geliştirilen birçok model sonucu kullanılan akma yüzey fonksiyonlarına ve malzemelerin anizotropik davranışlarını yansıtan model parametrelerine büyük ölçüde bağlı bulunmaktadır. Bu çalışma kapsamında BBC ailesi (BBC2000, 2003, 2005 ve 2008) akma yüzeyleri Marciniak-Kuczynski kararsızlık modeli ile 304L paslanmaz çeliğin şekillendirme sınır diyagramının oluşturulması noktasında kullanılmıştır. Modeller farklı anizotropi belirleme yöntemleri için değerlendirilmiş ve tahmin edilen sonuçlar deneysel sonuçlarla karşılaştırılmıştır.

🔖

Cite This Article

TOROS, S. (2017). EFFECT OF ANISOTROPY DETERMINATION METHODS ON FORMING LIMIT CURVE PREDICTION OF 304L STAINLESS STEEL. Niğde Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi, Cilt: 6 - Sayı: 2, 737–751. https://ajindex.com/articles/290354

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (16)

  1. KEELER S.P, BACKHOFEN W.A., “Plastic Instability and Fracture in Sheet Stretched over Rigid Punches”, ASM Trans Quart, 56, 25, 1964
  2. GOODWIN, G.M., “Application of Strain Analysis to Sheet Metal Forming in the Press Shop”, SAE paper, No. 680093, 380, 1968
  3. SWIFT, H.W., “Plastic Instability under Plane Stress”, J Mech Phys Solids, 1, 1, 1952
  4. HILL, R., “On Discontinuous Plastic States, with Special Reference to Localized Necking in Thin Sheets”, J. Mech. Phys. Solids, 1, 19, 1952
  5. HASHIGUCHI, K., PROTASOV A., “Localized Necking Analysis by the Subloading Surface Model with Tangential-Strain Rate and Anisotropy”, Int. J. Plasticity, 20, 1909, 2004
  6. BOUDEAU, N., GELIN, J.C., SALHI, S., “Computational Prediction of the Localized Necking in Sheet Forming Based on Microstructural Material Aspects”, Comput Mater Sci., 11, 45, 1998
  7. BRESSAN, J.D., WILLIAMS, J.A., “The use of a Shear Instability Criterion to Predict Local Necking in Sheet Metal Deformation”, Int J Mech Sci., 25, 155, 1983
  8. MARCINIAK, Z., KUCZYNSKI, K., “Limit Strains in the Processes of Stretch Forming Sheet Steel”. J. Mech. Phys. Solids, 1, 609, 1967
  9. HUTCHINSON, J.W., NEALE, K.W., Sheet Necking-II. Time Independent Behavior. In: Koistinen, DP, Wang NM, editors. Mechanics of Sheet Metal Forming. New York: Plenum Press, 1964
  10. BANABIC, D., ARETZ, H., PARAIANU, L., JURCO, P., “Applications of Various Fold Modeling Approaches”, Model Simul Mater Sci. Eng., 13, 759, 2005
  11. BANABIC, D., ARETZ, H.D., COMSA, S., PARAIANU, L., “An Improved Analytical Description of Orthotropy in Metallic Sheets”, Int J Plasticity, 21, 493, 2005
  12. HORA, P., TONG, L., REISSNER J., “A Prediction Method for Ductile Sheet Metal Failure in Fe-Simulation”, Proc. Numisheet’96 Conf., Dearborn, Michigan, 252, 1996
  13. ARRIEUX, R., BRUNET, M., VACHER, P., NHAT, T.N., “A Method to Predict the Onset of Necking in Numerical Simulation of Deep Drawing Operations”, CIRP Annals, 45, 255, 1996
  14. SLOTA, J., SPIŠÁK, E., “Comparison of the Forming Limit Diagram (FLD) Models for Drawing Quality (DQ) Steel Sheets”, Metalurgija, 44, 249, 2005
  15. ASTM E8/E8M-11 Standard Test Methods for Tension Testing of Metallic Materials. West Conshohocken: American Society for Testing and Materials; 2004
  16. TALONEN, J., NENONEN, P., PAPE, G., HÄNNINEN, H., “Effect of Strain Rate on the Strain-Induced Martensite Transformation and Mechanical Properties of Austenitic Stainless Steels”, Metall Mater Tra