SavedAdd your journal

Journals / Gazi University Journal of Science / 2010 / Cilt: 23 - Sayı: 1

Effect of Layer Arrangement on Expansion, Bending Strength and Modulus of Elasticity of Solid Wood and Laminated Veneer Lumber (LVL) Produced from Pine and Poplar

and Poplar

Yılmaz KILIÇ
Erol BURDURLU
Gülçin ELIBOL
Meliha ULUPINAR
Pages
89–96
Publication Date
2010-03-08
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The strength characteristics of the LVL increase as the percentage of Austrian pine increases.Key Words: Lamination, Laminated Veneer Lumber (LVL), Bending Strength, Modulus of Elasticity, PVAc Adhesive.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, it was aimed to determine whether or not the layer organizations were influential on the expansion in volume after keeping in water for 2 hours, on the bending strength and modulus of elasticity values of laminated veneer lumber (LVL).
📊
Key Findings & Data:Austrian pine (Pinus nigra) (A) and Lombardy poplar (Populus nigra) (B) veneers with thicknesses of 3 mm were used for the production of laminated veneer lumber.
💡
Conclusion & Impact:The strength characteristics of the LVL increase as the percentage of Austrian pine increases.Key Words: Lamination, Laminated Veneer Lumber (LVL), Bending Strength, Modulus of Elasticity, PVAc Adhesive.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Abstract

In this study, it was aimed to determine whether or not the layer organizations were influential on the expansion in volume after keeping in water for 2 hours, on the bending strength and modulus of elasticity values of laminated veneer lumber (LVL). Austrian pine (Pinus nigra) (A) and Lombardy poplar (Populus nigra) (B) veneers with thicknesses of 3 mm were used for the production of laminated veneer lumber. A total of 110 test specimens with 8 different layer organizations were prepared by using polyvinyl acetate based (PVAc-D4) adhesive. Solid Austrian pine and Lombardy poplar woods in the same dimensions were used as control specimens. At the end of the tests; the bending strength and modulus of elasticity values of all the LVLs with different combinations were found to be higher compared to the control specimens. The strength characteristics of the LVL increase as the percentage of Austrian pine increases.Key Words: Lamination, Laminated Veneer Lumber (LVL), Bending Strength, Modulus of Elasticity, PVAc Adhesive.

🔖

Cite This Article

KILIÇ, Y., BURDURLU, E., ELIBOL, G., ULUPINAR, M. (2010). Effect of Layer Arrangement on Expansion, Bending Strength and Modulus of Elasticity of Solid Wood and Laminated Veneer Lumber (LVL) Produced from Pine and Poplar. Gazi University Journal of Science, Cilt: 23 - Sayı: 1, 89–96. https://ajindex.com/articles/255039

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (11)

  1. Strickler, M.D., Pellerin, R.F., “Tension Proof Loading of Finger Joint for Laminated Beams”, Forest Products Journal, 21 (6): 10-15 (1971).
  2. Tichy, R.J., Bodig, G.J., “Flexural properties of glued laminated lodgepole pine dimension lumber”, Forest Products Journal, 29 (9): 52-64 (1978).
  3. Wolf, R., Moody, R.C., “Bending strength of vertically Products Journal, 30 (6): 32-40 (1979). beams”, Forest Marx, C.M., Moody, R.C., “Effects of lumber width and tension laminated quality on the bending strength of four ply laminated beams”, Forest Products Journal, 32 (1): 45-52 (1982).
  4. Youngquist, J., Laufenberg, T. L. and Bryant, S., “End Jointing of Laminated Veneer Lumber for Structural Use”, Forest Products Journal, 34 (11/12): 25-32 (1984).
  5. Baş, H.A., “Lamine Edilmiş Kızılçam'ın Fiziksel ve Mekanik Özellikleri ile Kullanım Olanaklarının Araştırılması”, Yüksek Lisans Tezi, Hacettepe Üniversitesi Fen Bilimleri Enstitüsü, Ankara (1995).
  6. Kılıç, Y., “Lamine Edilmiş Kızılağac'ın Fiziksel ve Mekanik Özellikleri ile Kullanım Olanaklarının Araştırılması”, Yüksek Lisans Tezi, Hacettepe Üniversitesi Fen Bilimleri Enstitüsü, Ankara (1997).
  7. Şenay, A., “Ahşap Lamine Taşıyıcı Elemanların Mekanik Özelliklerinin Belirlenmesi Üzerine Araştırmalar”, Doktora Tezi, İstanbul Üniversitesi Fen Bilimleri Enstitüsü, Istanbul (1996).
  8. Aydın, I., Çolak S., Çolakoğlu G., “A Comparative Study on Some Physical and Mechanical Properties of Laminated Veneer Lumber (LVL) Produced from Beech (Fagus Orientalis Lipsky) and Eucalyptus (Eucalyptus Camaldulensis Dehn) Veneers”, Holz als Roh-und Werkstoff, 62: 218- 220 (2004).
  9. Döngel, N., “Lamine ahşap malzemede ağaç türü katman sayısı ve tutkal, çeşidinin eğilme direncine etkileri”, Yüksek Lisans Tezi, Gazi Üniversitesi Fen Bilimleri Enstitüsü, Ankara (1999).
  10. Keskin, H., “Lamine Edilmiş Doğu Ladini (Picea orientalis Lipsky) Odununun Bazı Fiziksel ve Mekanik Üniversitesi Orman Fakültesi Dergisi, (A1): 139- 151 (2003).
  11. Süleyman Demirel Kılıç, Y., Çolak, M., Baysal, E., Burdurlu, E., “An investigation of some physical and mechanical properties manufactured from black alder (Alnus glutinosa) glued with polyvinyl acetate and polyurethane adhesives”, Forest Products Journal, 56(9): 56-59 (2006). veneer lumber Kılıç, M., Çelebi G., “Compression, cleavage and shear materials hardwoods”, Journal of Applied Polymer Science, 102: 3673-3678 (2006). construction produced softwoods and Pidaparti, R.M., Johnson, Lamination to Wood”, Journal of Polymer and Polymer Compos