Journals / El-Cezeri / 2020 / Cilt: 7 - Sayı: 2

Evaluation of Dry Sliding Wear Behavior of NiAl Base Materials

NiAl Bazlı Malzemelerin Kuru Kayma Aşınmasının İncelenmesi

Journal
El-Cezeri
Pages
563–571
Publication Date
2020-05-31
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

As a result of the studies, it was found that the amount of abrasion loss determined in the experiments using steel balls was much higher than that of ceramic balls.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, the wear behaviour of NiAl intermetallic, NiAl/Cr-Mo pseudo-eutectic and NiAl-Ti/Cr-Mo alloys which is considered as alternative material in different applications were investigated.
📊
Key Findings & Data:Wear tests were performed against steel (AISI 52100) and ceramic (Al2O3) balls.
💡
Conclusion & Impact:As a result of the studies, it was found that the amount of abrasion loss determined in the experiments using steel balls was much higher than that of ceramic balls.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:NiAl · intermetalik · aşınma

Abstract

In this study, the wear behaviour of NiAl intermetallic, NiAl/Cr-Mo pseudo-eutectic and NiAl-Ti/Cr-Mo alloys which is considered as alternative material in different applications were investigated. Wear tests were performed against steel (AISI 52100) and ceramic (Al2O3) balls. Test specimens were produced by arc melting method and abrasion tests were performed by ball on flat method under dry sliding conditions. Wear results were examined by hardness measurements, SEM investigations and EDX analyzes. As a result of the studies, it was found that the amount of abrasion loss determined in the experiments using steel balls was much higher than that of ceramic balls. Among the materials, the highest losses were seen in NiAl intermetallic in both abrasive balls, while the lowest losses were determined in Ti added pseudo-eutectic NiAl/Cr-Mo alloy.

Özet

Bu çalışmada farklı uygulamalarda alternatif malzeme olarak düşünülen ve bu amaçla üzerinde çalışılan NiAl intermetaliği ve tok fazlar ile mukavemetlendirilmiş NiAl/Cr-Mo ve NiAl-Ti/Cr-Mo alaşımlarının çelik (AISI 52100) ve seramik (Al2O3) bilyelere karşı aşınma davranışları incelenmiştir. Deney numuneleri ark ergitme yöntemi ile üretilmiş ve ball on disk yöntemi ile kuru kayma koşullarında aşınma deneyleri yapılmıştır. Elde edilen bulgular sertlik ölçümleri, SEM incelemeleri ve EDX analizleri ile irdelenmiştir. Yapılan çalışmalar neticesinde çelik bilye kullanılan deneylerde belirlenen aşınma miktarının seramik bilyedekine göre çok daha fazla olduğu tespit edilmiştir. Malzemeler arasında ise her iki aşındırıcı bilye türünde de en fazla aşınma kaybı NiAl intermetaliğinde yaşanırken en düşük kayıplar Ti ilaveli ötektiğimsi NiAl/Cr-Mo alaşımında belirlenmiştir.

🔖

Cite This Article

DEMİRTAŞ, H. (2020). Evaluation of Dry Sliding Wear Behavior of NiAl Base Materials. El-Cezeri, Cilt: 7 - Sayı: 2, 563–571. https://ajindex.com/articles/252551

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (16)

  1. Noebe R.D., Bowman R.R., Nathal M. "V. Physical and mechanical properties of the B2 compound NiAl", Int Mater Rev., 1993, 38(4): 193–232
  2. Bowman R.R., Noebe R.D. "Development of NiAl and NiAl-Based Composites for Structural Applications: A Status Report", 2012, 341–50
  3. George E.P., Yamaguchi M., Kumar K.S., Liu C.T. "Ordered intermetallics", Annu Rev Mater Sci., 1994, 24(1): 409–51
  4. Johnson D.R., Chen X.F., Oliver B.F., Noebe R.D., Whittenberger J.D. "Processing and mechanical properties of in-situ composites from the NiAlCr and the NiAl (Cr, Mo) eutectic systems", Intermetallics, 1995, 3(2): 99–113
  5. Liu E., Gao Y., Jia J., Bai Y., Wang W. "Microstructure and mechanical properties of in situ NiAl–Mo2C nanocomposites prepared by hot-pressing sintering", Mater Sci Eng A, 2014, 592: 201–6
  6. Darolia R., Walston W.S., Noebe R., Garg A., Oliver B.F. "Mechanical properties of high purity single crystal NiAl", Intermetallics, 1999, 7(10): 1195–202
  7. Yang J.M., Jeng S.M., Bain K., Amato R.A. "Microstructure and mechanical behavior of in-situ directional solidified NiAl/Cr (Mo) eutectic composite", Acta Mater., 1997, 45(1): 295–308
  8. Tiwari R., Tewari S.N., Asthana R., Garg A. "Development of NiAl-based intermetallic alloys: effect of chromium addition", Mater Sci Eng A, 1995, 192: 356–63
  9. Demirtas H., Gungor A. "Improvement of mechanical properties of NiAl-Cr (Mo) alloy by Ti addition", Optoelectron Adv Mater Commun., 2015, 9(7–8): 981–5
  10. Demirtas H., Gungor A. "Effect of Alloying Elements on the Microstructure and Mechanical Properties of NiAl-Cr (Mo) Eutectic Alloy", Mater Sci Non-Equilibrium Phase Transform., 2015, 1(2): 25–9
  11. Cotton J.D., Noebe R.D., Kaufman M.J. "Ternary alloying effects in polycrystalline {beta}-NiAl", Los Alamos National Lab., NM (United States); 1993
  12. Tang L.Z., Zhang Z.G., Li S.S., Gong S.K. "Mechanical behaviors of NiAl-Cr (Mo)-based near eutectic alloy with Ti, Hf, Nb and W additions", Trans Nonferrous Met Soc China, 2010, 20(2): 212–6
  13. Wilson A.W., Howe J.M. "Effect of alloying additions on β′ precipitation in NiAl–Ti base alloys", Acta Mater., 2001, 49(14): 2653–60
  14. Johnson B.J., Kennedy F.E., Baker I. "Dry sliding wear of NiAl", Wear, 1996, 192(1–2): 241–7
  15. Guo J., Wang Z., Sheng L., Zhou L., Yuan C., Chen Z., et al. "Wear properties of NiAl based materials", Prog Nat Sci Mater Int., 2012, 22(5): 414–25
  16. Kennedy F.E., Baker I., Johnson B.J. "Wear of ductile-phase toug