Journals / Bor Dergisi / 2019 / Cilt: 4 - Sayı: 1

The effect of different sintering temperatures on microstructure and hardness in Al-7Si%10B4C composite material production

Al-7Si%10B4C kompozit malzeme üretiminde farklı sinterleme sıcaklıklarının mikroyapı ve sertlik üzerine etkisi

Pages
60–65
Publication Date
2019-03-16
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Furthermore, it was determined that there is a significant increase in hardness values due to the increase in temperature values.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, Al-7Si%10B4C metal matrix composite material was produced by adding 10 wt. % B4C in weight into the Al-%7Si powder mixture, using powder metallurgy method.
📊
Key Findings & Data:The prepared powder mixtures were subjected to cold press under a pressure of 450 MPa and sintered for 60 minutes at different sintering temperatures (550°C, 570°C and 590°C) in an argon gas atmosphere.
💡
Conclusion & Impact:Furthermore, it was determined that there is a significant increase in hardness values due to the increase in temperature values.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Al-Si · B4C · MMK

Abstract

In this study, Al-7Si%10B4C metal matrix composite material was produced by adding 10 wt. % B4C in weight into the Al-%7Si powder mixture, using powder metallurgy method. The prepared powder mixtures were subjected to cold press under a pressure of 450 MPa and sintered for 60 minutes at different sintering temperatures (550°C, 570°C and 590°C) in an argon gas atmosphere. Microstructures of Al7Si%10B4C composite materials produced at different sintering temperatures were characterized by SEM+EDS, X-ray diffraction (XRD) and hardness measurements. As a result of the study, it was observed that Al3,21Si0,47 in matrix phase and AlB12, AlB10, phase and compounds between matrix and reinforcement were formed by increasing the sintering temperature. Furthermore, it was determined that there is a significant increase in hardness values due to the increase in temperature values.

Özet

Bu çalışmada, Al-7Si%10B4C metal matrisli kompozit malzeme, Al-%7Si toz karışımı içerisine ağırlıkça %10 oranında B4C ilave edilerek toz metalurjisi yöntemi kullanılarak üretilmiştir. Hazırlanan toz karışımları, 450 MPa basınç altında soğuk presleme işlemine tabi tutulmuş ve argon gazı atmosferinde farklı sinterleme sıcaklıklarında (550 oC, 570 oC ve 590 oC) 60 dakika süre ile sinterlenmiştir. Farklı sinterleme sıcaklıklarında üretilen Al7Si%10B4C kompozit malzemelerin mikro yapıları, SEM+EDS, X-ışını kırınımı (XRD) ve sertlik ölçümü ile karakterize edilmiştir. Çalışma sonucunda, sinterleme sıcaklığının artması ile matris fazında Al3,21Si0,47 ve matris-takviye arasında ise AlB12, AlB10, faz ve bileşikleri oluştuğu görülmüştür. Ayrıca sıcaklık değerlerindeki artışa bağlı olarak sertlik değerlerinde görülür bir artış olduğu belirlenmiştir.

🔖

Cite This Article

ÇOLAK, N. Y., TURHAN, H. (2019). The effect of different sintering temperatures on microstructure and hardness in Al-7Si%10B4C composite material production. Bor Dergisi, Cilt: 4 - Sayı: 1, 60–65. https://ajindex.com/articles/252177

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (13)

  1. Cerit A. A., Karamis M. B., Nair F., Yıldızlı K., Effect of reinforcement particle size and volume fraction on wear behaviour of metal matrix composites, Journal of Balkan Tribological Association, 12 (4), 482-489, 2008
  2. Jiang L., Wen H., Yang H., Hu T., Topping T., Zhang D., Schoenung J. M., Influence of length-scales on spatial distribution and interfacial characteristics of B4C in a nanostructured Al matrix, Acta Materialia, 89, 327-343, 2015
  3. Li M., Ma K., Jiang L., Yang H., Lavernia E. J., Zhang L., Schoenung J. M., Synthesis and mechanical behavior of nanostructured Al 5083/n-TiB2 metal matrix composites, Materials Science and Engineering: A, 656, 241-248, 2016
  4. Casati R., Vedani M., Metal matrix composites reinforced by nano-particles a review, Metals, 4(1), 65-83, (2014)
  5. Sharifi E. M., Karimzadeh F., Enayati M. H., Fabrication and evaluation of mechanical and tribological properties of boron carbide reinforced aluminum matrix nanocomposites, Materials & Design, 32(6), 3263-3271, 2011
  6. Alumınıja V. H. K. N. O., Wear behaviour of B4C reinforced hybrid aluminum-matrix composites, Materiali in tehnologije, 49(1), 9-13. 2015
  7. Çolak N, Turhan H., Toz Metalurjisi Yöntemi ile Üretilen Al-Si/B4C Kompozit Malzemenin Mikroyapı ve Mekanik Özelliklerinin Araştırılması, Fırat Üniversitesi Mühendislik Bilimleri Dergisi, 28 (2), 259-266., 2016
  8. Toptan F., Kilicarslan A., Karaaslan A., Cigdem M., Kerti I., Processing and microstructural characterisation of AA 1070 and AA 6063 matrix B4Cp reinforced composites, Materials & Design, 31, 87-91, 2010
  9. Mohanty R. M., Balasubramanian K., Seshadri S. K., Boron carbide-reinforced alumnium 1100 matrix composites: fabrication and properties, Materials Science and Engineering: A, 498 (1-2), 42-52, 2008
  10. Topçu I., Gülsoy H. O., Kadıoğlu N., Güllüoğlu A. N., Processing and mechanical properties of B4C reinforced Al matrix composites, Journal of Alloys and Compounds, 482 (1-2), 516-521, 2009
  11. Lü P., Yue X. Y., Yu L., Ru H. Q., Effect of in situ synthesized TiB2 on the reaction between B4C and Al in a vacuum infiltrated B4C–TiB2–Al composite, Journal of materials science, 44 (13), 3483-3487, 2009
  12. Ghasali E., Alizadeh M., Ebadzadeh T., hossein Pakseresht A., Rahbari A., Investigation on microstructural and mechanical properties of B4C–aluminum matrix composites prepared by microwave sintering. Journal of Materials Research and Technology, 4 (4), 411-415, 2015
  13. Hu H. M., La