Journals / Bor Dergisi / 2019 / Cilt: 4 - Sayı: 2

Investigation of the structural and magnetic properties of Fe70Ti10B20 (at.%) alloys by mechanical alloying

Pages
85–91
Publication Date
2019-06-30
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Magnetic measurements revealed that after 70 h of milling, the saturation magnetization (Ms) and the coercivity (Hc) was about 94 emu/g and 117 Oe.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, amorphous/nanocrystalline Fe70Ti10B20 (at.%) alloys were synthesized by using elemental Fe, Ti and B powders under argon gas atmosphere via mechanical alloying method.
📊
Key Findings & Data:The powders were ball milled at 20:1 ball-to-powder ratio and 500 rpm rotating speed up to 70 h.
💡
Conclusion & Impact:Magnetic measurements revealed that after 70 h of milling, the saturation magnetization (Ms) and the coercivity (Hc) was about 94 emu/g and 117 Oe.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Mechanical alloying · nanoparticles · magnetic properties

Abstract

In this study, amorphous/nanocrystalline Fe70Ti10B20 (at.%) alloys were synthesized by using elemental Fe, Ti and B powders under argon gas atmosphere via mechanical alloying method. The powders were ball milled at 20:1 ball-to-powder ratio and 500 rpm rotating speed up to 70 h. The phase and morphological properties of the synthesized powders were examined by using X-Ray diffractometer and scanning electron microscope with energy-dispersive X-ray spectroscope (SEM/EDX). The magnetic properties of powders were determined by vibrating sample magnetometer (VSM) at room temperature in the range of 0-20 kOe. It is determined that after 2.5 h of milling, Ti and B are started to dissolve in Fe lattice and Fe(TiB) solid solutions formed. XRD analysis revealed that the amorphous structures were formed after 30h of milling and the crystallite size and lattice strain were found ~ 8.2 nm and 1.16%, respectively. SEM images indicated that the particles were mostly agglomerated and the particles size distribution was in the range of 10-48 μm. Magnetic measurements revealed that after 70 h of milling, the saturation magnetization (Ms) and the coercivity (Hc) was about 94 emu/g and 117 Oe.

🔖

Cite This Article

ŞİMŞEK, T. (2019). Investigation of the structural and magnetic properties of Fe70Ti10B20 (at.%) alloys by mechanical alloying. Bor Dergisi, Cilt: 4 - Sayı: 2, 85–91. https://ajindex.com/articles/252149

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (17)

  1. Suryanarayana C., Mechanical alloying and milling, Prog. Mater. Sci., 46, 1–184, 2001
  2. Avar B., Simsek T., Gogebakan M., Mekanik alaşımlama ile üretilen Nanokristal Fe60Al30Cu10 (at.%) tozların yapısal ve mekanik özellikleri, G.U. J. Sci. Part C, 7 (1) 184-191, 2019
  3. Koch C. C., Cavin O. B., Mckamey C. G., Scarborough J. O., Preparation of “amorphous” Ni60Nb40 by mechanical alloying, Appl. Phys. Lett., 43, 1017–1019, 1983
  4. Avar B., Structural, thermal and magnetic characterization of nanocrystalline Co65Ti25W5B5 powders prepared by mechanical alloying, J. Non-Cryst. Solids., 432, 246–253, 2016
  5. Şimşek T., Şimşek T., Ozcan T., Synthesis and characterization of Mn2B nanocrystals by mechanical alloying method, Boron, 4, 25-30, 2019
  6. Birringer R., Nanocrystalline materials, Mater. Sci. Eng. A., 117, 33-43, 1989
  7. Simsek T., Pure YbB6 nanocrystals: First time synthesis via mechanochemical method, Adv. Powder Technol., 30, 1219–1225, 2019
  8. Zawrah M., Shaw L., Microstructure and hardness of nanostructured Al–Fe–Cr–Ti alloys through mechanical alloying, Mater. Sci. Eng. A.,, 355, 37-49, 2003
  9. Krifa M., Mhadhbi M., Escoda L., Güell J. M., Sunnol J. J., Isern N. L., Guzmaan C. A., Khitouni M., Nanocrystalline (Fe 60 Al 40 ) 80 Cu 20 alloy prepared by mechanical alloying, J. Alloys Compd., 554, 51–58, 2013
  10. Bahrami A. H., Ghayour H., Sharafi S., Evolution of microstructural and magnetic properties of mechanically alloyed Fe 80−x Ni 20 Si x nanostructured powders, Powder Technol., 249 7–14, 2013
  11. Sharifati A., Sharafi S., Structure and magnetic properties of mechanically alloyed (Fe 70 Co 30 ) 91 Cu 9 powder, Mater. Design., 36, 35–40, 2012
  12. McHenry M. E., Willard M. A., Laughlin D. E., Amorphous and nanocrystalline materials for applications as soft magnets, Prog. Mater. Sci., 44, 291-433, 1999
  13. Yoshizawa Y., Yamauchi K., Yamane T., Sugihara H., Common mode choke cores using the new Fe based alloys composed of ultrafine grain structure, J. Appl Phys., 64, 6044, 1988
  14. Shokrollahi H., The magnetic and structural properties of the most important alloys of iron produced by mechanical alloying, Mater. Design., 30, 3374–3387, 2009
  15. Jiles D., Introduction to Magnetism and Magnetic Materials, Chapman & Hall, London, 280–297, 1991
  16. Cullity B. D., Graham C. D., Introduction to Magnetic Materials, seconded, Wiley-IEEE Press, New Jersey, 2009
  17. Baghbaderani H. A., Sharafi S., Chermahini M. D., Investigati