SavedAdd your journal

Journals / Textile and Apparel / 2015 / Volume: 25 Issue: 2

RESEARCH ON OPTIMIZATION OF NIPPER MECHANISM ON CM500 COMBERS USING ADAMS

ADAMS KULLANARAK CM500 PENYE MAKINELERİNDE KISKAÇ MEKANİZMASI OPTİMİZASYONU ÜZERİNE ARAŞTIRMA

Xuzhong Su
Weidong Gao
Xinjin Lıu
Chunping Xıe
Bojun Xu
Pages
—
Publication Date
2015-12-01
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The simulation results show that vibrations of nipper are decreased significantly by optimization.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Comber is one of the important equipments on cotton yarn spinning.
📊
Key Findings & Data:In this paper, the research on optimization of nipper mechanism on CM500 series Combers was discussed using ADAMS software.
💡
Conclusion & Impact:The simulation results show that vibrations of nipper are decreased significantly by optimization.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Comber · Nipper mechanism · Optimization

Abstract

Comber is one of the important equipments on cotton yarn spinning. In this paper, the research on optimization of nipper mechanism on CM500 series Combers was discussed using ADAMS software. First, the nipper mechanisms moving characteristics of CM500 Combers was analyzed and the models of displacement, velocity, acceleration of nipper balance shaft were given. Then, the optimization of nipper system was discussed by using ADAMS software, and corresponding optimal crank radius was addressed. The simulation results show that vibrations of nipper are decreased significantly by optimization. The results obtained in this paper provide a theoretical support for product design

🔖

Cite This Article

Su, X., Gao, W., Lıu, X., Xıe, C., Xu, B. (2015). RESEARCH ON OPTIMIZATION OF NIPPER MECHANISM ON CM500 COMBERS USING ADAMS. Textile and Apparel, Volume: 25 Issue: 2. https://ajindex.com/articles/1640350

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (9)

  1. Erdogan M.C. and Pamuk O., 2007, Technical TextilesR21,Tekstil ve Konfeksiyon, Vol: 17(3), pp: 211-216.
  2. Liang J. J., Yang M. Q., Zhang W., Zhang J. R. and Sun Q. H., 2008, Vibration Analysis and Control for the Headstock system of cotton Comber, Noise and Vibration Control, Vol: 8, pp: 27-30.
  3. Subramanian S. and Gobi N., 2004, Effect of process parameters at comber on yam and fabric properties, Indian Journal of Fiber & Textile Research, Vol: 29(2), pp: 196-199.
  4. Chellamani K. P., Chattopadhyay D. and Thanabal V., 2003, Influence of wire point density in cards and combers on neps in sliver and yarn quality, Indian Journal of Fiber & Textile Research, Vol: 28(1), pp: 9-15.
  5. Belin R. E. and Taylor D. S., The Influence of Hooked Fibers on Cotton Comber Waste, Textile Research Journal, Vol: 36(6), pp:542-546.
  6. Schlatter N., 2005, Rieter enhances efficiency in combers by produced a new comber moderl E65/E75, TEKSTIL, Vol: 54(2), pp: 89-90.
  7. Chattopadhyay R. and Ghosh R., 2003, Studies on mass distribution profile of detached fibre fringe in a comber, Indian Journal of Fiber & Textile Research, Vol: 28(4), pp: 393-398.
  8. Xu B. J., Ma Q. H. and Liu X. J., Dynamic Balance Optimisation for the Middle Shaft System of a Cotton Comber Based on ADAMS, FIBRES & TEXTILES in Eastern Europe, Vol: 3(92), pp: 43-45.
  9. Zheng J. R., Introduction and advancement on ADAMS prototyping technology, Beijing: China Machine Press, 2002:74-108.