The results indicated that produced load cells could take measurements with sufficient accuracy and stability.
📌 3 Key Takeaways
🎯
Objective & Hypothesis:Load cells are widely used for the experiments conducted in structural mechanics.
📊
Key Findings & Data:In the current study, single directional load cells were produced by significantly, almost 90%, reducing the cost and these were tested in an experimental research on reinforced concrete members.
💡
Conclusion & Impact:The results indicated that produced load cells could take measurements with sufficient accuracy and stability.
Load cells are widely used for the experiments conducted in structural mechanics. However, since it is a high technology product, supplying load cell is very costly. Therefore, the need for different types and capacities of load cells specific to each experimental study may cause the funding allocated to the research to be exceeded. In the current study, single directional load cells were produced by significantly, almost 90%, reducing the cost and these were tested in an experimental research on reinforced concrete members. The results indicated that produced load cells could take measurements with sufficient accuracy and stability.
Özbek, E., Aykaç, B. (2020). A Load Cell Design that can be utilized for The Testing of Reinforced Concrete Members. Gazi University Journal of Science Part A: Engineering and Innovation, Volume: 7 Issue: 4. https://ajindex.com/articles/1398653
Aykaç, S., Jamal, R., Özbek, E., Kalkan, İ., & Aykaç, B. (2019). Behavior of Postfabricated RC Beams under Monotonic Transverse Loading. Journal of Structural Engineering, 145(1), 04018223-1-04018223-12. doi:10.1061/(ASCE)ST.1943-541X.0002220
ÇYHY. (2016). Çelik Yapıların Tasarım, Hesap ve Yapımına Dair Esaslar. Ministry of Environment and Urbanization, Ankara, Turkey.
Faruk, A. N. M., Liu, W., Lee, S. I., Naik, B., Chen, D. H., & Walubita, L. F. (2016). Traffic volume and load data measurement using a portable weigh in motion system: A case study. International Journal of Pavement Research and Technology, 9(3), 202-213.
Jenkins, J. M., & DeAngelis, V. M. (1997). A Summary of Numerous Strain-Gage Load Calibrations on Aircraft Wings and Tails in a Technological Format. NASA Technical Memorandum, 4804, 1-146.
Kaya, Y. (2020). Analaysis of the Bending Behavior of Slabless Reinforced Stairs. [MSc. Thesis] Gazi University
Kluger, J. M., Sapsis, T. P., & Slocum, A. H. (2016). A high-resolution and large force-range load cell by means of nonlinear cantilever beams. Precision Engineering, 43, 241-256.
Lin, H., Li, H., Shao, G., Ye, Y., & Yang, Y. (2020). Zero-point fault detection of load cells in truck scale based on recursive principal component analysis and comprehensive evaluation method. Measurement, 159, 107706-107715. doi:10.1016/j.measurement.2020.107706
Muller, I., de Brito, R. M., Pereira, C. E., & Brusamarello, V. (2010). Load Cells in Force Sensing Analysis – Theory and a Novel Application. IEEE Instrumentation & Measurement Magazine, 13(1), 15-19. doi:10.1109/MIM.2010.5399212
Özbek, E., Aykaç, B., & Aykaç, S. (2019). The effects of brick walls strengthened with perforated steel plates on frame behavior. Engineering Structures, 189, 62-76. doi:10.1016/j.engstruct.2019.03.080
TSE. (2006). TS EN 10025-2. Hot rolled products of structural steels – Part 2: Technical delivery conditions for non alloy structural steels. Turkish Standarts Instutition, Ankara, Turkey.
Tumialan, G., Galati, N., & Nanni, A. (2014a). Load Testing of Concrete Structures, Part 2: Test Protocols and Case Studies. Structure Magazine, June, 16-18.
Tumialan, G., Galati, N., & Nanni, A. (2014b). In-Situ Load Testing of Concrete Structures, Part 1: Rationale, Objectives, and Execution. Structure Magazine, April, 10-12.