SavedAdd your journal

Journals / Gazi University Journal of Science Part A: Engineering and Innovation / 2026 / Volume: 12 Issue: 3

Evaluating the Impact of Dynamic Behavior on the Al/SnO2/p-Si MOS Structures

Abdullah Karaca(YOZGAT BOZOK ÜNİVERSİTESİ)0000-0001-5001-5559
Pages
—
Publication Date
2025-09-30
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

As temperature was elevated from 273 K to 350 K, the results consistently showed a significant enhancement in carrier generation and mobility, leading to a reduction in both the overall impedance and charge transfer resistance.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:This study presents a comprehensive numerical analysis of Al/SnO2/p-Si metal–oxide–semiconductor (MOS) structures using the SCAPS-1D simulation framework, with a focus on elucidating the interplay between structural parameters and environmental conditions that govern device performance.
📊
Key Findings & Data:By systematically varying the thicknesses of the SnO2 layer and p-Si wafer, as well as simulating temperature-dependent behavior, the investigation reveals in electrical, spectral, and impedance characteristics.
💡
Conclusion & Impact:As temperature was elevated from 273 K to 350 K, the results consistently showed a significant enhancement in carrier generation and mobility, leading to a reduction in both the overall impedance and charge transfer resistance.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:MOS Structures · I-V · C-V

Abstract

This study presents a comprehensive numerical analysis of Al/SnO2/p-Si metal–oxide–semiconductor (MOS) structures using the SCAPS-1D simulation framework, with a focus on elucidating the interplay between structural parameters and environmental conditions that govern device performance. By systematically varying the thicknesses of the SnO2 layer and p-Si wafer, as well as simulating temperature-dependent behavior, the investigation reveals in electrical, spectral, and impedance characteristics. Thinner SnO2 films enhance forward bias current and spectral response due to reduced series resistance and increased optical transparency, whereas thicker films effectively suppress leakage currents, preserving rectification behavior. The p-Si wafer thickness is shown to significantly influence near-infrared absorption and carrier collection efficiency, showing its importance in photodetector design. As temperature was elevated from 273 K to 350 K, the results consistently showed a significant enhancement in carrier generation and mobility, leading to a reduction in both the overall impedance and charge transfer resistance. This was evidenced by the systematic decrease in Nyquist semicircle diameter and the leftward shift of C-V curves. The study also confirmed the thermally activated nature of interface states, whose activity was found to be highly sensitive to temperature variations. The findings validate SCAPS-1D as a reliable tool for modeling MOS heterojunctions and provide actionable design principles for optimizing SnO2/p-Si-based optoelectronic devices intended for imaging, sensing, and energy conversion applications.

🔖

Cite This Article

Karaca, A. (2025). Evaluating the Impact of Dynamic Behavior on the Al/SnO2/p-Si MOS Structures. Gazi University Journal of Science Part A: Engineering and Innovation, Volume: 12 Issue: 3. https://doi.org/10.54287/gujsa.1766682

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (40)

  1. Afre, R. A., Sharma, N., Sharon, M., & Sharon, M. (2018). Transparent conducting oxide films for various applications: A review. Reviews on Advanced Materials Science, 53(1), 79-89. https://doi.org/10.1515/rams-2018-0006
  2. Al-Ahmadi, N. A. (2020). Metal oxide semiconductor-based Schottky diodes: a review of recent advances. Materials Research Express, 7(3), 032001. https://doi.org/10.1088/2053-1591/ab7a60
  3. Aldemir, D. A., Benhaliliba, M., & Benouis, C. E. (2020). Photodiode based on Al-doped SnO2: Fabrication, current-voltage and capacitance-conductance-voltage measurements. Optik, 222, 165487. https://doi.org/10.1016/j.ijleo.2020.165487
  4. Altındal, Ş., Karadeniz, S., Tuğluoğlu, N., & Tataroğlu, A. (2003). The role of interface states and series resistance on the I–V and C–V characteristics in Al/SnO2/p-Si Schottky diodes. Solid-State Electronics, 47(10), 1847-1854. https://doi.org/10.1016/S0038-1101(03)00182-5
  5. Barreira, E. A., Pedrini, L. F., Boratto, M. H., & Scalvi, L. V. (2020). A dynamic time-temperature-dependent process for thermal oxidation of Sn leading to SnOx thin films: Impedance spectroscopy study. International Journal of Modern Physics B, 34(19), 2050184. https://doi.org/10.1142/S0217979220501842
  6. Benhaliliba, M., Benouis, C. E., & Aldemir, D. A. (2019). The presence of C/ω-V and G/ω-V peaks profile of Ag/SnO2/n-Si/Au MOS junction for capacitor applications. Physica B: Condensed Matter, 572, 175-183. https://doi.org/10.1016/j.physb.2019.07.043
  7. Birkan Selçuk, A. (2007). On the dielectric characteristics of Au/SnO2/n-Si capacitors. Physica B: Condensed Matter, 396(1), 181-186. https://doi.org/10.1016/j.physb.2007.04.002
  8. Chauhan, S., & Singh, R. (2023). Analysis of absorber layer for wide-bandgap double perovskite solar cell using SCAPS-1D. Materials Today: Proceedings. https://doi.org/10.1016/j.matpr.2023.05.201
  9. Chenari, H. M., Golzan, M., Sedghi, H., Hassanzadeh, A., & Talebian, M. (2011). Frequency dependence of dielectric properties and electrical conductivity of Cu/nano-SnO2 thick film/Cu arrangement. Current Applied Physics, 11(4), 1071-1076. https://doi.org/10.1016/j.cap.2011.01.038
  10. Chetia, A., Saikia, D., & Sahu, S. (2022). Design and optimization of the performance of CsPbI3 based vertical photodetector using SCAPS simulation. Optik, 269, 169804. https://doi.org/10.1016/j.ijleo.2022.169804
  11. Dhiman, S., Meena, R., Manyani, N., & Tripathi, S. K. (2023). Investigating the temperature and frequency dependence of dielectric response using AC impedance spectroscopy on SnO2. Surfaces and Interfaces, 42, 103362. https://doi.org/10.1016/j.surfin.2023.103362
  12. Dixit, H., Porwal, S., Boro, B., Paul, M., Ghosh, S., Mishra, S., & Singh, T. (2022). A theoretical exploration of lead-free double perovskite La2NiMnO6 based solar cell via SCAPS-1D. Optical Materials, 131, 112611. https://doi.org/10.1016/j.optmat.2022.112611
  13. Erbilen Tanrıkulu, E., Güçlü, Ç. Ş., Altındal, Ş., & Durmuş, H. (2024). A high sensitivity temperature coefficient of the Au/n-Si with (CdTe-PVA) structure based on capacitance/conductance-voltage (C/G-V) measurements in a wide range of temperature. Measurement, 238, 115316. https://doi.org/10.1016/j.measurement.2024.115316
  14. Erdal, M. O., Kocyigit, A., & Yıldırım, M. (2019). Temperature dependent current-voltage characteristics of Al/TiO2/n-Si and Al/Cu: TiO2/n-Si devices. Materials Science in Semiconductor Processing, 103, 104620. https://doi.org/10.1016/j.mssp.2019.104620
  15. Hassun, H. K., Hussein, B. H., Salman, E. M. T., & Shaban, A. H. (2020). Photoelectric properties of SnO2: Ag/P–Si heterojunction photodetector. Energy Reports, 6, 46-54. https://doi.org/10.1016/j.egyr.2019.10.017
  16. Jiao, Y., Lu, G., Feng, Y., Zhang, C., Wang, W., Wu, S., Chen, M., Ma, M., Li, W., Yang, C., & Li, W. (2021). Towards high sensitivity infrared detector using Cu2CdxZn1-xSnSe4 thin film by SCAPS simulation. Solar Energy, 225, 375-381. https://doi.org/10.1016/j.solener.2021.07.044
  17. Karaca, A., Yıldız, D. E., & Yıldırım, M. (2024). Optimizing optoelectronics performance: theoretical and experimental study on ZnO thin film for Al/ZnO/p-Si photodiode. Physica Scripta, 99(11), 115904. https://doi.org/10.1088/1402-4896/ad7d45
  18. Karaca, A., Yıldız, D. E., & Yıldırım, M. (2025). Comparing experimental and numerical approaches in the analysis of n-TiO2/p-Si photodiodes. Physica Scripta. https://doi.org/10.1088/1402-4896/ada58c
  19. Karadeniz, S., Tuğluoğlu, N., Serin, T., & Serin, N. (2005). The energy distribution of the interface state density of SnO2/p-Si (1 1 1) heterojunctions prepared at different substrate temperatures by spray deposition method. Applied Surface Science, 246(1-3), 30-35. https://doi.org/10.1016/j.apsusc.2004.11.022
  20. Karthick, S., Velumani, S., & Bouclé, J. (2020). Experimental and SCAPS simulated formamidinium perovskite solar cells: A comparison of device performance. Solar Energy, 205, 349-357. https://doi.org/10.1016/j.solener.2020.05.041
  21. Kaur, M., Gupta, S. K., Betty, C. A., Saxena, V., Katti, V. R., Gadkari, S. C., & Yakhmi, J. V. (2005). Detection of reducing gases by SnO2 thin films: an impedance spectroscopy study. Sensors and Actuators B: Chemical, 107(1), 360-365. https://doi.org/10.1016/j.snb.2004.10.024
  22. Kim, Y. J., Kumar, M. R., Kumar, G. M., & Kim, M. (2023). Self-powered silicon metal–semiconductor–metal photodetector based on asymmetric Schottky barrier heights. Applied Physics Letters, 123(25). https://doi.org/10.1063/5.0178740
  23. Korotcenkov, G., Brinzari, V., & Cho, B. (2016). In2O3‐and SnO2‐Based Thin Film Ozone Sensors: Fundamentals. Journal of Sensors, 2016(1), 3816094. https://doi.org/10.1155/2016/3816094
  24. Koushik, R. P., Kalita, J., & Mishra, R. (2024). Facile assembly of SnO2 thin film-based Al/SnO2/Al device for sensing of 260 nm UVC and 365 nm UVA radiation. Sensors and Actuators A: Physical, 379, 115991. https://doi.org/10.1016/j.sna.2024.115991
  25. Lekshmy, S. S., Daniel, G. P., & Joy, K. (2013). Microstructure and physical properties of sol gel derived SnO2:Sb thin films for optoelectronic applications. Applied Surface Science, 274, 95-100. https://doi.org/10.1016/j.apsusc.2013.02.109
  26. Mahani, R., Ashery, A., & Elnasharty, M. M. M. (2020). Frequency and Voltage Dependence of the Dielectric Properties of Ni/SiO2/P-Si (MOS) Structure. Silicon, 12(8), 1879-1885. https://doi.org/10.1007/s12633-019-00277-4
  27. Majda-Zdancewicz, E., Suproniuk, M., Pawłowski, M., & Wierzbowski, M. (2018). Current state of photoconductive semiconductor switch engineering. Opto-Electronics Review, 26(2), 92-102. https://doi.org/10.1016/j.opelre.2018.02.003
  28. Mehraj, S., & Ansari, M. S. (2013). Structural, dielectric and complex impedance properties of Cd doped SnO2 nanoparticles. Journal of Nanoengineering and Nanomanufacturing, 3(3), 229-236.
  29. Mwema, F. M., Jen, T.-C., & Zhu, L. (2022). Thin film coatings: properties, deposition, and applications. CRC Press. https://doi.org/10.1201/9781003202615
  30. Ozel, K., & Yildiz, A. (2021). The potential barrier-dependent carrier transport mechanism in n-SnO2/p-Si heterojunctions. Sensors and Actuators A: Physical, 332, 113141. https://doi.org/10.1016/j.sna.2021.113141
  31. Paul David, S., Soosaimanickam, A., Sakthivel, T., Sambandam, B., & Sivaramalingam, A. (2021). Thin film metal oxides for displays and other optoelectronic applications. Metal and Metal Oxides for Energy and Electronics, 185-250. https://doi.org/10.1007/978-3-030-53065-5_6
  32. Prades, J. D., Jimenez-Diaz, R., Hernandez-Ramirez, F., Barth, S., Cirera, A., Romano-Rodriguez, A., Mathur, S., & Morante, J. R. (2009). Equivalence between thermal and room temperature UV light-modulated responses of gas sensors based on individual SnO2 nanowires. Sensors and Actuators B: Chemical, 140(2), 337-341. https://doi.org/10.1016/j.snb.2009.04.070
  33. Rejaiba, O., Braña, A. F., & Matoussi, A. (2016). Study of various technological parameters on the CVg and the GVg characteristics of MOS structures. The European Physical Journal Plus, 131, 1-12. https://doi.org/10.1140/epjp/i2016-16281-5
  34. Schipani, F., Miller, D. R., Ponce, M. A., Aldao, C. M., Akbar, S. A., Morris, P. A., & Xu, J. C. (2017). Conduction mechanisms in SnO2 single-nanowire gas sensors: An impedance spectroscopy study. Sensors and Actuators B: Chemical, 241, 99-108. https://doi.org/10.1016/j.snb.2016.10.061
  35. Tataroğlu, A., & Altındal, Ş. (2008). Study on the frequency dependence of electrical and dielectric characteristics of Au/SnO2/n-Si (MIS) structures. Microelectronic Engineering, 85(9), 1866-1871. https://doi.org/10.1016/j.mee.2008.05.025
  36. Tomaev, V., Moshnikov, V., Miroshkin, V., Gar'Kin, L., & Zhivago, A. Y. (2004). Impedance spectroscopy of metal-oxide nanocomposites. Glass Physics and Chemistry, 30, 461-470. https://doi.org/10.1023/B:GPAC.0000045928.95952.ba
  37. Tuğluoğlu, N., Altındal, Ş., Tataroğlu, A., & Karadeniz, S. (2004). Dielectric properties in Au/SnO2/n-Si (MOS) structures irradiated under 60Co-γ rays. Microelectronics Journal, 35(9), 731-738. https://doi.org/10.1016/j.mejo.2004.06.004
  38. Wang, X., Wu, Z., Zhu, J., Kang, Y., Cai, M., Xia, Y., & Deng, H. (2024). Design and optimization of the performance of self-powered Sb2S3 photodetector by SCAPS-1D simulation and potential application in imaging. Optical Materials, 147, 114594. https://doi.org/10.1016/j.optmat.2023.114594
  39. Xu, M., Xu, Z., Sun, Z., Chen, W., Wang, L., Liu, Y., Wang, Y., Du, X., & Pan, S. (2023). Surface Engineering in SnO2/Si for High-Performance Broadband Photodetectors. ACS Applied Materials & Interfaces, 15(2), 3664-3672. https://doi.org/10.1021/acsami.2c20073
  40. Yan, X., Wang, X., Gao, S., & Qiao, W. (2023). High‐Performance Organic Photodetectors Using SnO2 as Interfacial Layer with Optimal Thickness. physica status solidi (a), 220(1), 2200667. https://doi.org/10.1002/pssa.202200667