AI Summary & Key Takeaways
AI InsightThe high performance values obtained in this study demonstrate notable advancements compared to existing literature.
📌 3 Key Takeaways
Abstract
As the power conversion efficiency (PCE) of perovskite solar cells rapidly increases, the low stability of 3D perovskites against moisture, light, and heat remains as a significant challenge. In this study, it is aimed to enhance the stability and performance of a 3D perovskite solar cell structure including 2D perovskite layers. Using SCAPS-1D software, an NIP-type solar cell in the structure of FTO/SnO₂/3D Perovskite/2D Perovskite/NiO/Au was modele and simulated under AM1.5G solar spectrum and 300 K ambient temperature. The optimal electron transport layer (ETL) and hole transport layer (HTL) materials were obtained as tin dioxide (SnO₂) and nickel oxide (NiO), respectively. The simulations were also revealed that increasing the 3D perovskite layer thickness enhances short circuit current (Jsc) but reduces open-circuit voltage (Voc) and fill factor (FF) and increasing the thickness of the 2D perovskite layer adversely affects performance of the cell. Additionally, it was observed that higher defect density in the 3D perovskite layer significantly degrades solar cell performance. In the optimized design, a structure comprising a 3D perovskite layer with a thickness of 900 nm and a 2D perovskite layer of 9 nm was achieved Voc of 1.40 V, Jsc of 25.59 mA/cm², FF of 79.59%, and PCE of 28.58%. This innovative approach, which has been explored in only a limited number of studies, offers significant improvements in the efficiency and stability of solar cells. The high performance values obtained in this study demonstrate notable advancements compared to existing literature.
Özet
Perovskit güneş hücrelerinin güç dönüşüm verimliliği (PCE) hızla artarken, 3 boyutlu (3B) perovskitlerin neme, ışığa ve ısıya karşı düşük stabilitesi önemli bir sorun olarak varlığını sürdürmektedir. Bu çalışmada, 2 boyutlu (2B) perovskit katmanları içeren 3B perovskit güneş hücresi yapısının stabilitesini ve performansını artırmak amaçlanmıştır. SCAPS-1D yazılımı kullanılarak, FTO/SnO₂/3B Perovskit/2B Perovskit/NiO/Au yapısına sahip NIP tipi bir güneş hücresi, AM1.5G güneş spektrumu ve 300 K ortam sıcaklığı altında modellenmiş ve simüle edilmiştir. En uygun elektron taşıyıcı katman (ETL) ve delik taşıyıcı katman (HTL) malzemeleri sırasıyla kalay dioksit (SnO₂) ve nikel oksit (NiO) olarak belirlenmiştir. Simülasyon sonuçları, 3B perovskit katman kalınlığının artırılmasının kısa devre akım yoğunluğunu (Jsc) artırırken açık devre gerilimini (Voc) ve dolgu faktörünü (FF) azalttığını, 2B perovskit katman kalınlığının artırılmasının ise hücre performansını olumsuz etkilediğini ortaya koymuştur. Ayrıca, 3B perovskit katmanındaki yüksek kusur yoğunluğunun güneş hücresi performansını önemli ölçüde düşürdüğü gözlemlenmiştir. Optimize edilen yapıda, 900 nm kalınlığında 3B perovskit ve 9 nm kalınlığında 2B perovskit katmanları kullanılarak; 1,40 V Voc, 25,59 mA/cm² Jsc, %79,59 FF ve %28,58 PCE değerleri elde edilmiştir. Sınırlı sayıda çalışmada ele alınmış olan bu yenilikçi yaklaşım, güneş hücrelerinin verimlilik ve stabilitesinde önemli gelişmeler sunmaktadır. Bu çalışmada elde edilen yüksek performans değerleri, mevcut literatürdeki çalışmalara kıyasla dikkat çekici ilerlemeleri ortaya koymaktadır