Journals / Karaelmas Fen ve Mühendislik Dergisi / 2026 / Cilt: 16 Sayı: 2

INVESTIGATION OF THE RELATIONSHIP BETWEEN SURFACE AREA AND PORE SIZE OF ACTIVATED CARBONS PRODUCED FROM ZONGULDAK COAL AND H2 ADSORPTION

ZONGULDAK KÖMÜRÜNDEN ÜRETİLEN AKTİF KARBONLARIN YÜZEY ALANI VE GÖZENEK BOYUTUNUN H2 ADSORPSİYONU İLE İLİŞKİSİNİN ARAŞTIRILMASI

Atakan Toprak(ZONGULDAK BÜLENT ECEVİT ÜNİVERSİTESİ)0000-0003-0008-1456
Pages
78–87
Publication Date
2026-07-24
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

According to the results, H2O vapor activation was shown to be an effective method for improving surface area and pore properties.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, the development and optimization of activated carbons with varying pore and surface properties derived from Zonguldak coal were conducted to efficiently store hydrogen as a clean energy source, addressing the increasing global energy demand and environmental pollution.
📊
Key Findings & Data:In the experimental section, activated carbons were produced by impregnating coal samples with ash content removed using H3PO4, and then activating them at 800°C and 900°C under N2 and N2-H2O vapor, using two different methods.
💡
Conclusion & Impact:According to the results, H2O vapor activation was shown to be an effective method for improving surface area and pore properties.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Aktif karbon · Hidrojen depolama · H2O aktivasyonu

Abstract

In this study, the development and optimization of activated carbons with varying pore and surface properties derived from Zonguldak coal were conducted to efficiently store hydrogen as a clean energy source, addressing the increasing global energy demand and environmental pollution. In the experimental section, activated carbons were produced by impregnating coal samples with ash content removed using H3PO4, and then activating them at 800°C and 900°C under N2 and N2-H2O vapor, using two different methods. According to the results, H2O vapor activation was shown to be an effective method for improving surface area and pore properties. The highest BET surface area and micropore volume were obtained in the H900-H2O sample. The H2 storage capacity at 77 K and 1 atm was obtained in the H900-H2O sample, which contained 1.58% by weight of H2. According to the correlation studies between H2 adsorption and surface area and micropore size, it was determined that the H2 adsorption capacity is related to specific pore sizes rather than the BET surface area. Specifically, a very high linear relationship of correlation coefficient (R2) 0.999 was found between the ultra-micropore volume (5-10 Å range) of activated carbons and their H2 capacity. Consequently, it was concluded that the hybrid (physical and chemical) activation method applied to coals is highly effective in creating the ultra-micropore structure ideal for H2 storage. It was determined that the obtained H2 adsorption results were competitive with those of some advanced porous structures reported in the literature, such as COF-102, ZIF-8, and MOF-5.

Özet

Bu çalışmada, artan küresel enerji gereksinimi ve çevre kirliliğine karşı temiz bir enerji kaynağı olarak hidrojenin verimli bir şekilde depolanması için Zonguldak kömüründen farklı gözenek ve yüzey özelliklerine sahip aktif karbonların geliştirilmesi ve optimizasyonu yapılmıştır. Deneysel aşamada, kül içeriği giderilen kömür numunesi H3PO4 ile impregne edilerek 800°C ve 900°C sıcaklıklarda N2 ve N2-H2O buharı altında iki farklı yöntemle aktivasyon işlemi ile aktif karbonlar üretilmiştir. Elde edilen sonuçlara göre, H2O buharı aktivasyonunun yüzey alanı ve gözenek özelliklerinin geliştirmede etkili bir yöntem olduğu göstermiştir. En yüksek BET yüzey alanı ve mikro gözenek hacmi H900-H2O numunesinde elde edilmiştir. 77 K ve 1 atm’de H2 depolama kapasitesi ağırlıkça %1.58 ile H900-H2O numunesinde elde edilmiştir. H2 adsorpsiyonunun yüzey alanı ve mikro gözenek boyutları ile arasındaki korelasyon çalışmalarına göre, H2 adsorpsiyon kapasitesinin BET yüzey alınından ziyade belirli gözenek boyutlarıyla ilişkili olduğunu belirlenmiştir. Özellikle aktif karbonların 5-10 Å aralığındaki ultra mikro gözenek hacmi ile H2 kapasitesi arasında belirleme katsayısı (R2) 0.999 gibi oldukça yüksek bir doğrusal ilişki tespit edilmiştir. Sonuç olarak, kömürlere uygulanan hibrit (fiziksel ve kimyasal) aktivasyon yönteminin, H2 depolama için ideal olan ultra mikro gözenekli yapının oluşturulmasında son derece etkili olduğu sonucuna varılmıştır. Elde edilen H2 adsorpsiyon sonuçlarının literatürdeki COF-102, ZIF-8 ve MOF-5 gibi bazı gelişmiş gözenekli yapılar ile rekabet edebildiği belirlenmiştir.

🔖

Cite This Article

Toprak, A. (2026). INVESTIGATION OF THE RELATIONSHIP BETWEEN SURFACE AREA AND PORE SIZE OF ACTIVATED CARBONS PRODUCED FROM ZONGULDAK COAL AND H2 ADSORPTION. Karaelmas Fen ve Mühendislik Dergisi, Cilt: 16 Sayı: 2, 78–87. https://doi.org/10.7212/karaelmasfen.1849674

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (30)

  1. Anuchitsakol, S., Dilokekunakul, W., Khongtor, N., Chaemchuen, S., & Klomkliang, N. (2023). Combined experimental and simulation study on H2 storage in oxygen and nitrogen co-doped activated carbon derived from biomass waste: Superior pore size and surface chemistry development. RSC Advances, 13(51), 36009. https://doi.org/10.1039/d3ra06720c
  2. Bader, N., & Ouederni, A. (2016). CO2 activation of olive bagasse for hydrogen storage. Environmental Progress & Sustainable Energy, 36(1), 315. https://doi.org/10.1002/ep.12514
  3. Benard, P., & Chahine, R. (2001). Determination of the adsorption isotherms of hydrogen on activated carbons. Langmuir, 17(6), 1950–1955. https://doi.org/10.1021/la001381x
  4. Bicil, Z., & Doğan, M. (2021). Characterization of activated carbons prepared from almond shells and their hydrogen storage properties. Energy & Fuels, 35(12), 10227. https://doi.org/10.1021/acs.energyfuels.1c00795 Edwards, R., Font-Palma, C., & Howe, J. (2020). The status of hydrogen technologies in the UK: A multi-disciplinary review. Sustainable Energy Technologies and Assessments, 43, 100901. https://doi.org/10.1016/j.seta.2020.100901
  5. Furukawa, H., & Yaghi, O. M. (2009). Storage of hydrogen, methane, and carbon dioxide in highly porous covalent organic frameworks. Journal of the American Chemical Society, 131(25), 8875–8883. https://doi.org/10.1021/ja9015765
  6. Gogotsi, Y., Portet, C., Osswald, S., Simmons, J. M., Yildirim, T., Laudisio, G., & Fischer, J. E. (2009). Importance of pore size in high-pressure hydrogen storage by porous carbons. International Journal of Hydrogen Energy, 34(15), 6314. https://doi.org/10.1016/j.ijhydene.2009.05.073
  7. Gregg, S. J., & Sing, K. S. W. (1991). Adsorption, surface area, and porosity (2. baskı). Academic Press.
  8. Huang, J., Liang, Y., Dong, H., Hu, H., Yu, P., Peng, L., Zheng, M., Xiao, Y., & Liu, Y. (2018). Revealing contribution of pore size to high hydrogen storage capacity. International Journal of Hydrogen Energy, 43(39), 18077. https://doi.org/10.1016/j.ijhydene.2018.08.027
  9. Kahilu, G. M., Bada, S., & Mulopo, J. (2023). Systematic physicochemical characterization, carbon balance and cost of production analyses of activated carbons derived from (Co)-HTC of coal discards and sewage sludge for hydrogen storage applications. Waste Disposal & Sustainable Energy, 5(2), 125. https://doi.org/10.1007/s42768-023-00136-4
  10. Kaye, S. S., Dailly, A., Yaghi, O. M., & Long, J. R. (2007). Impact of preparation and handling on the hydrogen storage properties of Zn4O(1,4-benzenedicarboxylate)3 (MOF-5). Journal of the American Chemical Society, 129(46), 14176–14177. https://doi.org/10.1021/ja076877g
  11. Kumar, N., Lee, S., & Park, S. (2024). Advancements in hydrogen storage technologies: A comprehensive review of materials, methods, and economic policy. Nano Today, 56, 102302. https://doi.org/10.1016/j.nantod.2024.102302
  12. Liu, X., Zhang, C., Geng, Z., & Cai, M. (2014). High-pressure hydrogen storage and optimizing fabrication of corncob-derived activated carbon. Microporous and Mesoporous Materials, 194, 60. https://doi.org/10.1016/j.micromeso.2014.04.005
  13. López, L. F., Morales-Ospino, R., Castro‐Gutiérrez, J., Celzard, A., & Fierro, V. (2025). Enhanced hydrogen storage and release capacities when using HKUST-1@activated carbon hybrids obtained by resonant acoustic mixing. Chemical Engineering Journal, 165834. https://doi.org/10.1016/j.cej.2025.165834
  14. Lozano‐Castelló, D., Cazorla‐Amorós, D., & Linares-Solano, Á. (2004). Usefulness of CO2 adsorption at 273 K for the characterization of porous carbons. Carbon, 42(7), 1233. https://doi.org/10.1016/j.carbon.2004.01.037 Masika, E., & Mokaya, R. (2012). Hydrogen storage in high surface area carbons with identical surface areas but different pore sizes: Direct demonstration of the effects of pore size. The Journal of Physical Chemistry C, 116(49), 25734. https://doi.org/10.1021/jp3100365
  15. Meng, L., & Park, S. (2012). Investigation of narrow pore size distribution on carbon dioxide capture of nanoporous carbons. Bulletin of the Korean Chemical Society, 33(11), 3749. https://doi.org/10.5012/bkcs.2012.33.11.3749
  16. Naheed, L., Koppel, M., Paalo, M., Alsabawi, K., Lamb, K., Gray, E., Jänes, A., & Webb, C. J. (2021). Hydrogen adsorption properties of carbide-derived carbons at ambient temperature and high pressure. International Journal of Hydrogen Energy, 46(29), 15761. https://doi.org/10.1016/j.ijhydene.2021.02.109
  17. Park, K. S., Ni, Z., Côté, A. P., Choi, J. Y., Huang, R., Uribe-Romo, F. J., Chae, H. K., O'Keeffe, M., & Yaghi, O. M. (2006). Exceptional chemical and thermal stability of zeolitic imidazolate frameworks. Proceedings of the National Academy of Sciences, 103(27), 10186–10191
  18. Ramesh, T., Rajalakshmi, N., & Dhathathreyan, K. S. (2015). Activated carbons derived from tamarind seeds for hydrogen storage. Journal of Energy Storage, 4, 89. https://doi.org/10.1016/j.est.2015.09.005
  19. Ramírez-Vidal, P., Canevesi, R. L. S., Sdanghi, G., Schaefer, S., Maranzana, G., Celzard, A., & Fierro, V. (2021). A step forward in understanding the hydrogen adsorption and compression on activated carbons. ACS Applied Materials & Interfaces, 13(10), 12562. https://doi.org/10.1021/acsami.0c22192
  20. Rivard, E., Trudeau, M. L., & Zaghib, K. (2019). Hydrogen storage for mobility: A review. Materials, 12(12), 1973. https://doi.org/10.3390/ma12121973
  21. Rowsell, J. L., & Yaghi, O. M. (2006). Effects of functionalization, catenation, and variation of the metal oxide and organic linking units on the low-pressure hydrogen adsorption properties of metal–organic frameworks. Journal of the American Chemical Society, 128(4), 1304–1315. https://doi.org/10.1021/ja0562916
  22. Samantaray, S. S., Putnam, S. T., & Stadie, N. P. (2021). Volumetrics of hydrogen storage by physical adsorption. Inorganics, 9(6), 45. https://doi.org/10.3390/inorganics9060045
  23. Schaefer, S., Fierro, V., Izquierdo, M. T., & Celzard, A. (2016). Assessment of hydrogen storage in activated carbons produced from hydrothermally treated organic materials. International Journal of Hydrogen Energy, 41(28), 12146. https://doi.org/10.1016/j.ijhydene.2016.05.000
  24. Sdanghi, G., Canevesi, R. L. S., Celzard, A., Thommes, M., & Fierro, V. (2020). Characterization of carbon materials for hydrogen storage and compression. C – Journal of Carbon Research, 6(3), 46. https://doi.org/10.3390/c6030046
  25. Sultana, A. I., Saha, N., & Reza, M. T. (2021). Synopsis of factors affecting hydrogen storage in biomass-derived activated carbons. Sustainability, 13(4), 1947. https://doi.org/10.3390/su13041947
  26. Texier-Mandoki, N., Dentzer, J., Piquero, T., Saadallah, S., David, P., & Vix‐Guterl, C. (2004). Hydrogen storage in activated carbon materials: Role of the nanoporous texture. Carbon, 42, 2744. https://doi.org/10.1016/j.carbon.2004.05.018
  27. Toprak, A. (2020). The effect of pore and surface characteristics of activated carbon produced by coal through N2 and H2O vapor/H3PO4 activation on a single step for CH4 adsorption in the low pressure. Energy Sources, Part A: Recovery, Utilization, and Environmental Effects, 42(16), 1950. https://doi.org/10.1080/15567036.2019.1604904
  28. Toprak, A., & Kopaç, T. (2011). Surface and hydrogen sorption characteristics of various activated carbons developed from Rat Coal Mine (Zonguldak) and anthracite. Chinese Journal of Chemical Engineering, 19(6), 931. https://doi.org/10.1016/s1004-9541(11)60074-8
  29. Vergara-Rubio, A., Ribba, L., Picón, D., Sapag, K., Candal, R., & Goyanes, S. (2022). Ultramicroporous carbon nanofibrous mats for hydrogen storage. ACS Applied Nano Materials, 5(10), 15353. https://doi.org/10.1021/acsanm.2c03401
  30. Yang, J., Wang, H., Dong, X., & Gong, M. (2023). Performances comparison of adsorption hydrogen storage tanks at a wide temperature and pressure zone. International Journal of Hydrogen Energy, 48(69), 26881. https://doi.org/10.1016/j.ijhydene.2023.03.351