Dergiler / Forestist / 2017 / Cilt: 67 Sayı: 2

Isıl işlemli ahşap malzemelerin yüzey renk özelliklerine farklı ahşap verniklerinin etkisi

The effect of different wood varnishes on surface color properties of heat treated wood materials

Sayfa
262–274
Yayın Tarihi
2017-07-01
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

DOI: 10.17099/jffiu.300010

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Özet: Bu çalışmada, ısıl işlemli ahşapların yüzey renk özelliklerine farklı ahşap verniklerinin etkisi araştırılmıştır.
📊
Temel Bulgular & Veri:Doğu kayını (Fagus oriantalis L.) ve sarıçam (Pinus sylvestris L.) odunundan hazırlanmış örneklere 190, 200 ve 210 °C sıcaklıkta 2 saat süresince ısıl işlem uygulanmıştır.
💡
Sonuç & Katkı:DOI: 10.17099/jffiu.300010
🔬Tür:Araştırma Makalesi
📍Kapsam:2017 Verileri
⚙️Değişkenler:Ahşap malzeme · Isıl işlem · Vernik

Özet

Özet: Bu çalışmada, ısıl işlemli ahşapların yüzey renk özelliklerine farklı ahşap verniklerinin etkisi araştırılmıştır. Doğu kayını (Fagus oriantalis L.) ve sarıçam (Pinus sylvestris L.) odunundan hazırlanmış örneklere 190, 200 ve 210 °C sıcaklıkta 2 saat süresince ısıl işlem uygulanmıştır. Daha sonra örnek yüzeyleri selülozik (SZ), sentetik (ST), poliüretan (PU) ve su bazlı (SB) ahşap vernikleri ile kaplanmıştır. Örneklerin renk özellikleri üç boyutlu CIEL*a*b* renk uzayına göre belirlenmiştir. Araştırma sonuçlarına göre, ısıl işlem sonrası işlem sıcaklığına bağlı olarak örneklerde L* değeri %64, b* değeri %70 oranında azalmıştır. a* değeri ise sarıçam örneklerde %96’ya kadar artarken, kayın örneklerde %56 oranına kadar azalmıştır. Isıl işlemli örneklerin renk değerleri vernik uygulamalarından sonra önemli derecede değişmiştir. Verniksiz örneklere göre tüm örneklerin L* değeri azalmış ve örnekler daha da koyulaşmıştır. Vernikleme sonrası, ısıl işlemli sarıçam örneklerin a* değeri önemli oranda artarken, yüksek sıcaklıkta (200 ve 210 °C) ısıl işlemli kayın örneklerde genellikle azalmıştır. b* değeri ise PU ve ST vernik uygulanmış her iki ağaç türünde önemli oranda azalmıştır. Verniklenmiş örneklerdeki toplam renk değişimi (ΔE*) değeri genel olarak 200 °C’de ısıl işlemli örneklerde daha yüksektir. Ayrıca, renk değişiminde ST vernik en fazla etkiye sahip iken, SB vernik en az etkiye sahiptir. Isıl işlem sonrası kayın ve sarıçam odunlarında elde edilen ahşap renginin maksimum düzeyde korunması arzu ediliyor ise SB vernikler tercih edilebilir.Anahtar kelimeler: Ahşap malzeme, ısıl işlem, vernik, renk değişimiReceived (Geliş): 23.03.2017 - Revised (Düzeltme): 08.06.2017 - Accepted (Kabul): 19.06.2017Cite (Atıf): Pelit, H., 2017. The effect of different wood varnishes on surface color properties of heat treated wood materials. Journal of the Faculty of Forestry Istanbul University 67(2): 355-367. DOI: 10.17099/jffiu.300010

Abstract

Abstract: This study investigates the effects of different wood varnishes on the surface color properties of heat treated wood. Samples prepared from Oriental beech (Fagus orientalis L.) and Scots pine (Pinus sylvestris L.) are subjected to heat treatment at 190, 200, and 210 ° C for 2 h. Sample surfaces are then covered with cellulosic (SZ), synthetic (ST), polyurethane (PU), and water-based (SB) wood varnishes, and the color properties of samples are determined according to the three-dimensional CIEL*a*b* color space. Results show a decrease in the L* and b* values of samples by 64% and 70%, respectively, depending on the process temperature after heat treatment. The a* value increases by up to 96% for Scots pine samples and up to 56% for beech samples. Color values of heat treated samples change significantly after varnish is applied; L* values of all samples are reduced compared to unvarnished samples and samples are seen to darken. However, the a* value of heat treated Scots pine samples increases significantly after varnishing, while that of heat-treated beech samples at high temperatures (200 and 210 °C) generally decreases. Nevertheless, the b* value decreases significantly in both wood species subjected to application of PU and ST varnishes, and the total color change (ΔE*) of varnished specimens is generally higher for samples heat-treated at 200 °C. Results show that ST varnish has the largest effect on color change and SB varnish has the smallest effect. The use of SB varnishes is thus preferable when it is necessary to preserve the color of samples from either species following heat treatment.Keywords: Wood material, heat treatment, varnish type, color changeReceived (Geliş): 23.03.2017 - Revised (Düzeltme): 08.06.2017 - Accepted (Kabul): 19.06.2017Cite (Atıf): Pelit, H., 2017. The effect of different wood varnishes on surface color properties of heat treated wood materials. Journal of the Faculty of Forestry Istanbul University 67(2): 355-367. DOI: 10.17099/jffiu.300010

🔖

Bu Makaleye Atıf Yap

Pelit, H. (2017). Isıl işlemli ahşap malzemelerin yüzey renk özelliklerine farklı ahşap verniklerinin etkisi. Forestist, Cilt: 67 Sayı: 2, 262–274. https://ajindex.com/articles/990369

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (9)

  1. Akgül, M., Korkut, S., 2012. The effect of heat treatment on some chemical properties and colour in Scots pine and Uludağ fir wood. African Journal of Biotechnology 7(21): 2854-2859.
  2. Aksoy, A., Deveci, M., Baysal, E., Toker, H., 2011. Colour and gloss changes of Scots pine after heat modification. Wood Research 56(3): 329-336. ASTM D2244-15a, 2015. Standard Practice for Calculation of Color Tolerances and Color Differences From Instrumentally measured color coordinates. American Society for Testing and Materials, USA. ASTM D3023-98, 2011. Standard Practice for Determination of Resistance of Factory-Applied Coatings on Wood Products to Stains and Reagents. American Society for Testing and Materials, USA. Ayadi, N., Lejeune, F., Charrier, F., Charrier, B., Merlin, A., 2003. Color stability of heat-treated wood during artificial weathering. Holz als Roh-und Werkstoff 61(3): 221-226.
  3. Aydemir, D., Gündüz, G., 2009. The effect of heat treatment on physical, chemical, mechanical and biological properties of wood. Journal of The Bartın Faculty of Forestry 11(15): 71-81 [Turkish]. Aydemir, D., Gündüz, G., Altuntaş, E., Ertas, M., Şahin, H.T., Alma, M.H., 2011. Investigating changes in the chemical constituents and dimensional stability of heat-treated hornbeam and Uludağ fir wood. BioResources 6(2): 1308-1321.
  4. Baysal, E., Kart, S., Toker, H., Degirmentepe, S., 2014. Some physical characteristics of thermally treated Oriental beech wood. Maderas Ciencia y Tecnologia 16(3): 291-298.
  5. Bekhta, P., Niemz, P., 2003. Effect of high temperature on the change in color, dimensional stability and mechanical properties of spruce wood. Holzforschung 57: 539-546.
  6. Bekhta, P., Proszyk, S., Krystofiak, T., 2014. Colour in short-term thermo-mechanically densified veneer of various wood species. European Journal of Wood and Wood Products 72(6): 785-797.
  7. Boonstra, M.J., 2008. A Two-Stage Thermal Modification of Wood, Ph.D. Thesis, Co-supervised by Ghent University, Ghent, Belgium, and Université Henry Poincaré, Nancy, France. Esteves, B.M., Pereira, H.M. 2009. Wood modification by heat treatment: A review. BioResources 4(1): 370-404. González-Peña, M.M., Hale, M.D., 2009. Colour in thermally modified wood of beech, Norway spruce and Scots pine. Part 1: Colour evolution and colour changes. Holzforschung 63(4): 385-393.
  8. Gündüz, G., Aydemir, D., 2009. Some physical properties of heat-treated Hornbeam (Carpinus betulus) wood. Drying Technology 27(5): 714-720.
  9. Gündüz, G., Aydemir, D., Korku