Dergiler / Bor Dergisi / 2023 / Cilt: 8 Sayı: 3

Toz Metalurjisi Yöntemi ile Hazırlanan AlCu-B4C Kompozitlerin Yoğunluğuna İmalat Değişkenlerinin Etkisinin İncelenmesi

Investigation of the Effect of Manufacturing Parameters on the Density of AlCu-B4C Composites Prepared by Powder Metallurgy Method

Sayfa
92–98
Yayın Tarihi
2023-09-30
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Bu tasarım ile yapılan analizler sonucunda elde edilen S/N oranı yanıtlarına göre, sıkıştırma basıncının en yüksek etkiye, takviye oranının da görece düşük etkiye sahip olduğu gözlemlenmiştir.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Bu çalışmada, toz metalurjisi yöntemi ile hazırlanan, farklı oranlarda (hacimce % 0, 10 ve 20) B4C parçacık takviyeli Al-%10Cu ana yapılı kompozit malzemenin sinterleme sonrası yoğunluğuna, takviye oranı, sıkıştırma basıncı ve sinterleme sıcaklığının etkisi incelenmiştir.
📊
Temel Bulgular & Veri:Tayin edilen değişkenlerin sinterleme sonrası yoğunluğa etkisi Taguchi deney tasarımı yöntemi kullanılarak incelenmiştir.
💡
Sonuç & Katkı:Bu tasarım ile yapılan analizler sonucunda elde edilen S/N oranı yanıtlarına göre, sıkıştırma basıncının en yüksek etkiye, takviye oranının da görece düşük etkiye sahip olduğu gözlemlenmiştir.
🔬Tür:Modelleme & Sayısal Simülasyon
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:AlCu anayapı · B4C takviye · Toz metalürjisi

Özet

Bu çalışmada, toz metalurjisi yöntemi ile hazırlanan, farklı oranlarda (hacimce % 0, 10 ve 20) B4C parçacık takviyeli Al-%10Cu ana yapılı kompozit malzemenin sinterleme sonrası yoğunluğuna, takviye oranı, sıkıştırma basıncı ve sinterleme sıcaklığının etkisi incelenmiştir. Kompozit üretimi için yüksek saflıkta alaşım ve seramik tozları kullanılmış, elde edilen homojen karışım soğuk preste sıkıştırılmış ve tüp fırında sinterlenmiştir. Tayin edilen değişkenlerin sinterleme sonrası yoğunluğa etkisi Taguchi deney tasarımı yöntemi kullanılarak incelenmiştir. Bu amaç ile sürece en uygun Taguchi tasarımı olan, L9 ortogonal deney tasarımı seçilmiş ve deneyler bu matrise göre gerçekleştirilmiştir. Bu tasarım ile yapılan analizler sonucunda elde edilen S/N oranı yanıtlarına göre, sıkıştırma basıncının en yüksek etkiye, takviye oranının da görece düşük etkiye sahip olduğu gözlemlenmiştir. Taguchi deney tasarımı ve yapılan regresyon analizi sonucunda, oluşturulan regresyon modelinin ise %95 güven aralığın içinde olduğu sonucu elde edilmiştir.

Abstract

In this study, the effect of reinforcement ratio, compression pressure and sintering temperature on the post-sintering density of Al-10%Cu matrix composite material with B4C particle reinforcement at different ratios (0, 10 and 20% by volume) prepared by powder metallurgy method was investigated. High-purity alloy and ceramic powders were used for composite production, the obtained homogeneous mixture was compressed in a cold press and sintered in a tube furnace. The effect of the variables on the density after sintering was investigated using the Taguchi experimental design method. For this purpose, the L9 orthogonal experimental design, which is the most suitable Taguchi design for the process, was chosen and the experiments were carried out according to this matrix. According to the S/N ratio responses obtained as a result of the analyzes made with this design, it was observed that the compression pressure had the highest effect and the reinforcement ratio had a relatively low effect. As a result of the Taguchi experimental design and the regression analysis, it was concluded that the regression model was within the 95% confidence interval.

🔖

Bu Makaleye Atıf Yap

EKER, M., ZALAOĞLU, D. (2023). Toz Metalurjisi Yöntemi ile Hazırlanan AlCu-B4C Kompozitlerin Yoğunluğuna İmalat Değişkenlerinin Etkisinin İncelenmesi. Bor Dergisi, Cilt: 8 Sayı: 3, 92–98. https://ajindex.com/articles/962989

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (9)

  1. Chang, Y., Yao, X., Chen, Y., Huang, L., & Zou, D. (2023). Review on ceramic-based composite phase change materials: Preparation, characterization and application. Composites Part B: Engineering, 254, 110584. https:// doi.org/10.1016/j.compositesb.2023.110584. Shabani, M. O., & Mazahery, A. (2012). The GA optimization performance in the microstructure and mechanical properties of MMNCs. Transactions of the Indian Institute of Metals, 65(1), 77-83. https://doi.org/10.1007/s12666-011-0110-9.
  2. Mazahery, A., & Shabani, M. O. (2012). Tribological behaviour of semisolid–semisolid compocast Al–Si matrix composites reinforced with TiB2 coated B4C particulates. Ceramics International, 38(3), 1887-1895. https://doi.org/10.1016/j.ceramint.2011.10.016.
  3. Shabani, M. O., Mazahery, A., Rahimipour, M. R., & Razavi, M. (2012). FEM and ANN investigation of A356 composites reinforced with B4C particulates. Journal of King Saud University-Engineering Sciences, 24(2), 107- 113. https://doi.org/10.1016/j.jksues.2011.05.001.
  4. Mazahery, A., & Shabani, M. O. (2012). Nano-sized silicon carbide reinforced commercial casting aluminum alloy matrix: Experimental and novel modeling evaluation. Powder Technology, 217, 558-565. https://doi.org/10.1016/j.powtec.2011.11.020.
  5. Yang, Q. S., He, X. Q., Liu, X., Leng, F. F., & Mai, Y. W. (2012). The effective properties and local aggregation effect of CNT/SMP composites. Composites Part B: Engineering, 43(1), 33-38. https://doi.org/10.1016/j.compositesb.2011.04.027.
  6. Kumar, S., & Ghosh, S. K. (2023). Comparative study of airborne particles on new developed metal matrix compositeku and commercial brake pad materials with ANN and finite element analysis. Computational Particle Mechanics, 10(2), 273-287. https://doi.org/10.1007/ s40571-022-00491-9.
  7. Chatterjee, A., Sen, S., Paul, S., Roy, P., Seikh, A. H., Alnaser, I. A., … & Ghosh, M. (2023). Fabrication and characterization of SiC-reinforced aluminium matrix composite for brake pad applications. Metals, 13(3), 584. https://doi.org/10.3390/met13030584.
  8. Biyik S. (2019). Investigation of the effect of different process control agents on the production of Cu25W composite powder via ball milling technique.Gümüşhane University Journal of Science and Technology, 9(2), 222- 228. https://doi.org/10.17714/gumusfenbil.426995.
  9. Biyik, S., Arslan, F., & Aydin, M. (2015). Arc-erosion behavior of boric oxide-reinforced silver-based electrical contact materials produced by mechanical alloying. Journal of Electronic Ma