KaydedilenlerDerginizi ekleyin

Dergiler / Sakarya University Journal of Science / 2019 / Cilt: 23 Sayı: 2

Electrochemical Corrosion Behavior of High Velocity Oxy-Fuel (HVOF) Superalloy Coatings On Ductile Irons

Yusuf KAYALI
Muhammet KARABAŞ
Yılmaz YALÇIN
Aysel BÜYÜKSAĞİŞ
Şükrü TALAŞ
Sayfa
291–300
Yayın Tarihi
2019-04-01
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

The presence of intermetallic phases in the coating produced with AMDRY 9624 increased the corrosion resistance of the coatings.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:In this study, alloyed and unalloyed ductile irons (DI) were coated with two different Ni-based superalloy materials by HVOF method.
📊
Temel Bulgular & Veri:The electrochemical corrosion behavior of alloyed and unalloyed DI is investigated in 3.5% (w / v) NaCl solution.
💡
Sonuç & Katkı:The presence of intermetallic phases in the coating produced with AMDRY 9624 increased the corrosion resistance of the coatings.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:HVOF · Ductile Iron · Electrochemical Methods

Abstract

In this study, alloyed and unalloyed ductile irons (DI) were coated with two different Ni-based superalloy materials by HVOF method. Microstructure and phase analyzes of the coatings were performed by using SEM, EDX, XRD methods. The electrochemical corrosion behavior of alloyed and unalloyed DI is investigated in 3.5% (w / v) NaCl solution. As a result of the characterization studies, it was observed that a dense non-porous coating layer of about 80 μm thickness was obtained on the cast iron samples and continuous adhesion was provided between the coating and the substrate. It has been determined that the cast iron coated with AMDRY 9624 contains γ and β intermetallic phases and the coating produced with AMDRY 9951 commercial powder contains only γ phase. As a result of coating process, the corrosion rate of the alloyed and unalloyed spherical graphite cast irons is reduced. Also, the corrosion rate of the coating produced with AMDRY 9951 is higher than the coating produced with AMDRY 9624. The presence of intermetallic phases in the coating produced with AMDRY 9624 increased the corrosion resistance of the coatings.

🔖

Bu Makaleye Atıf Yap

KAYALI, Y., KARABAŞ, M., YALÇIN, Y., BÜYÜKSAĞİŞ, A., TALAŞ, Ş. (2019). Electrochemical Corrosion Behavior of High Velocity Oxy-Fuel (HVOF) Superalloy Coatings On Ductile Irons. Sakarya University Journal of Science, Cilt: 23 Sayı: 2, 291–300. https://ajindex.com/articles/942055

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (13)

  1. R., Singh, “Cast Iron Metallurgy. Materials Performance”, 48 (9), pp. 58-61, 2009
  2. R., O'Rourke, “Cast Iron: The engineered metal”, Advanced Materials Processes, 159 (1), pp. 65-68, 2001
  3. J.L., Liu, G.Q., Shi, P.D., Ding, H.O., Ye, Z.X., Ou, “Features of laser alloying of grey cast iron”, Lasers in Engineering, 6(2), pp. 81-101, 1997
  4. X., Cheng, S.B., Hu, W.L., Song, X. S., Xiong, “Improvement in corrosion resistance of a nodular cast iron surface modified by plasma beam treatment”, Applied Surface Science, 286, pp. 334-343, 2013
  5. Z., Lestan, M., Milfelner, J., Balic, M., Brezocnik, I., Karabegovic, “Laser deposition of Metco 15E, Colmony 88 and VIM CRU 20 powders on cast iron and low carbon steel”, International Journal of Advanced Manufacturing Technology, 66(9-12), pp. 2023-2028, 2013
  6. A.L. Maco and F.J. Belzunce, “Laser surface hardening of gray cast irons”, Revista De Metalurgia, 34(2), pp. 126-130, 1998
  7. V., Ozcelik, U., Oliveira, M., Boer, J.T.M., Hosson, “Thick Co-based coating on cast iron by side laser cladding: Analysis of processing conditions and coating properties”, Surface & Coatings Technology, 201(12), pp. 5875-5883, 2007
  8. F., Fernandes, A., Cavaleiro and A., Loureiro, “Oxidation behavior of Ni-based coatings deposited by PTA on gray cast iron”, Surface & Coatings Technology, 207, pp. 196-203, 2012
  9. P., Fauchais and A., Vardelle, “Thermal sprayed coatings used against corrosion and corrosive wear, in Advanced plasma spray applications”, InTech., 2012.[10] J., Yoganandh, S., Natarajan and S.P.K., Babu, “Erosion Behaviour of WC-Co-Cr Thermal Spray Coated Grey Cast Iron under Mining Environment”, Transactions of the Indian Institute of Metals, 66(4), pp. 437-443, 2013
  10. J., Vetter, G., Barbezat, J., Crummenauer, J. Avissar, “Surface treatment selections for automotive applications”, Surface and Coatings Technology, 200(5), pp. 1962-1968, 2005
  11. I.G., Wright and B.A., Pint, “Bond coating issues in thermal barrier coatings for industrial gas turbines”, Proceedings of the Institution of Mechanical Engineers Part a-Journal of Power and Energy, 219(A2), pp. 101-107, 2005
  12. Y., Itoh, M. Saitoh M. Tamura, “Characteristics of MCrAIY coatings sprayed by high velocity oxygen-fuel spraying system”, Journal of Engineering for Gas Turbines and Power-Transactions of the Asme, 122(1), pp. 43-49, 2000
  13. Z.W., Huang, Z.G., Wang, S.J., Zhu, F.H., Yuan, F. G., Wang, “Effect of HVOF sprayed MCrAIY coating on th