KaydedilenlerDerginizi ekleyin

Dergiler / Turkish Journal of Engineering / 2019 / Cilt: 3 Sayı: 2

INVESTIGATION OF MACHINABILITY PROPERTIES OF LASER TREATED S355JR CARBON STEEL WITH ZRB2 NANOPARTICLES

Tuncay ŞİMŞEK
Mustafa BARİS
Sadan OZCAN
Adnan AKKURT
Sayfa
51–59
Yayın Tarihi
2019-04-01
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Intensive thermal deformation was also observed in the method of laser cutting.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:In this study, the machinability properties of laser treated S355JR samples were investigated.
📊
Temel Bulgular & Veri:The ZrB2 nanoparticles were coated on the surface of S355JR carbon steel by 2 kW CO2 laser.
💡
Sonuç & Katkı:Intensive thermal deformation was also observed in the method of laser cutting.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Laser coating · Nanoparticles · Machinability

Abstract

In this study, the machinability properties of laser treated S355JR samples were investigated. The ZrB2 nanoparticles were coated on the surface of S355JR carbon steel by 2 kW CO2 laser. Then the coated samples were cut using the methods of abrasive water jet, wire-cut electrical discharge machining, laser, and abrasive disc, respectively. The phase structures and morphologies of the coated and cut surfaces were determined by using X-Ray diffractometry, optical microscope and scanning electron microscopy. The hardness was specified by using the microhardness device. It was found that low heat input and minimal damage was observed with the abrasive disc cutting method. Cutting with wire-cut electrical discharge machining, the worn zone was in a very narrow range, but there was also some heat-affected zone. While no heat input was seen in the method of cutting with abrasive water jet, significant damages in the shear edges and peripheral zones were observed due to abrasive particles. Intensive thermal deformation was also observed in the method of laser cutting.

🔖

Bu Makaleye Atıf Yap

ŞİMŞEK, T., BARİS, M., OZCAN, S., AKKURT, A. (2019). INVESTIGATION OF MACHINABILITY PROPERTIES OF LASER TREATED S355JR CARBON STEEL WITH ZRB2 NANOPARTICLES. Turkish Journal of Engineering, Cilt: 3 Sayı: 2, 51–59. https://ajindex.com/articles/934301

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (9)

  1. Akgün, B., Çamurlu, H.E., Topkaya, Y., Sevinç, N. (2011). “Mechanochemical and volume combustion sythesis of ZrB2.” International Journal of Refractory Metals and Hard Materials, Vol. 29, pp. 601-607
  2. Aouici, H., Bouchelaghem, H. Yallese, M. A., Elbah, M., Fnides, B. (2014) “ Machinability investigation in hard turning of AISI D3 cold work steel with ceramic tool using response surface methodology.” InternationalJournal of Advanced Manufacturing Technology, Vol.73, pp. 1775–1788.
  3. Avar, B., Ozcan, Ş. (2015). “Characterization and amorphous phase formation of mechanically alloyed Co60Fe5Ni5Ti25B5 powders.” Journal of Alloys and Compounds Vol. 650, pp. 53-58.
  4. Baudis, U., Fitchte, R. (1985). Boric oxide and boric acid and borates, Schwetz, KA, Lipp A, Capbll FT, Pfefferkom R(Eds.). Boron carbide, boron nitride, and metal borides, Zirconium and zirconium compounds, Ullmann's Encyclopedia of Industrial Chemistry, Fifth, Completely Revised Edition A4, Wiley-VCH, Weinheim, 263-307, 91. Berger, L.M. (2015). “Application of hardmetals as thermal spray coatings.” International Journal of Refractory Metals and Hard Materials, Vol. 49, pp. 350–364.
  5. Buldum, B.B., Şık, A., Ozkul, I. (2012). “Investigation of Magnesium Alloys Machinability.” International Journal Of Electronics; Mechanical And Mechatronics Engineering, Vol.2, pp. 261-268.
  6. Bouzakis, K.D., Charalampous, P., Kotsanis, T., Skordaris, G., Bouzakis, E., Denkena, B., Breidenstein, B., Aurich, J.C., Zimmermann, M., Herrmann, T., M’saoubi R. (2017). “Effect of HM substrates’ cutting edge roundness manufactured by laser machining and micro-blasting on the coated tools’ cutting performance.” CIRP Journal of Manufacturing Science and Technology, Vol. 18, pp. 188–197.
  7. Cheng, E. J., Li., J., Sakamoto, Y., Han, S., Sun, H., Noble, J., Katsui, H., Goto, T. (2017). “Mechanical properties of individual phases of ZrB2-ZrC eutectic composite measured by nano indentation.” Journal of the European Ceramic Society, Vol. 37, pp. 4223-4227.
  8. Chi, Y., Gu, G., Yu, H., Chen, C. (2018). “Laser surface alloying on aluminum and its alloys: A review.” Optics and Lasers in Engineering, Vol. 100, pp. 2337. Dangio, A., Zoua, J., Binner, J., Ma, H.B., Hilmas, G.E., Fahrenholtz, W.G. (2018). “Mechanical properties and grain orientation evolution of zirconium diboridezirconium carbide ceramics.” Journal of the European Ceramic Society, Vol. 38, pp. 391-402.
  9. Dai, X., Yan, D., Yang, Y., Chu, Z., Chen, X., Song, J. (2017). “In situ (Al,Cr)2O3-Cr