Dergiler / Pamukkale Üniversitesi Mühendislik Bilimleri Dergisi / 2023 / Cilt: 29 - Sayı: 1

TIG kaynak parametrelerinin AISI 316L paslanmaz çeliğinin mikro yapı ve mekanik özelliklerine etkisi

The effects of TIG welding parameters on the microstructure and mechanical properties of AISI 316L stainless steel

Sayfa
76–85
Yayın Tarihi
2023-02-28
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Yapılan 1800 eğme testlerinde ise ne kep eğmelerinde ne de kök eğmelerinde herhangi bir yırtılma ya da çatlamaya rastlanmamıştır.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Bu çalışmada yüksek korozyon direnci nedeni ile nükleer güç santrallerinde yaygın bir şekilde kullanılan AISI 316L östenitik paslanmaz çelik, TIG kaynak yöntemi ile farklı kaynak akımlarında ve kaynak hızlarında, ilave tel kullanılmadan birleştirilmiştir.
📊
Temel Bulgular & Veri:Daha sonra üretilen kaynaklı birleştirmelerin ısı girdileri hesaplanarak, numunelere makro ve mikroyapı çalışmaları, sertlik, çekme ve eğme testleri uygulanmıştır.
💡
Sonuç & Katkı:Yapılan 1800 eğme testlerinde ise ne kep eğmelerinde ne de kök eğmelerinde herhangi bir yırtılma ya da çatlamaya rastlanmamıştır.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:TIG kaynağı · AISI 316L paslanmaz çelik · Mikroyapı

Özet

Bu çalışmada yüksek korozyon direnci nedeni ile nükleer güç santrallerinde yaygın bir şekilde kullanılan AISI 316L östenitik paslanmaz çelik, TIG kaynak yöntemi ile farklı kaynak akımlarında ve kaynak hızlarında, ilave tel kullanılmadan birleştirilmiştir. Daha sonra üretilen kaynaklı birleştirmelerin ısı girdileri hesaplanarak, numunelere makro ve mikroyapı çalışmaları, sertlik, çekme ve eğme testleri uygulanmıştır. Mikroyapı çalışmaları sonucunda kaynak metalinin östenit+çatısal ferrit ya da delta ferritten oluşan bir mikroyapıya sahip olduğu görülmüştür. Sertlik deneyleri sonucunda kaynak akımının artması ile sertliğin düştüğü gözlenirken kaynak hızının artması ile de sertliğin yükseldiği belirlenmiştir. Çekme deneyleri sonuçları ise sertlik ölçümleri ile benzerlik göstererek kaynak akımının artması ile çekme dayanımı düşerken kaynak hızının artması ile çekme dayanımı artmıştır. Yapılan 1800 eğme testlerinde ise ne kep eğmelerinde ne de kök eğmelerinde herhangi bir yırtılma ya da çatlamaya rastlanmamıştır.

Abstract

In this study, AISI 316L austenitic stainless steel, which is widely used in nuclear power plants due to its high corrosion resistance, is joined by TIG welding method at different welding currents and welding speeds without using additional wire. Then, the heat inputs of the produced welded joints were calculated and macro and microstructure studies, hardness, tensile and bending tests were applied to the samples. As a result of the microstructure studies, it has been observed that the weld metal has a microstructure consisting of austenite + Skeletal ferrite or delta ferrite. As a result of the hardness tests, it was observed that the hardness decreased with the increase of the welding current, and the hardness increased with the increase of the welding speed. As a result of the tensile tests, similar to the hardness measurements, the tensile strength decreased with the increase of the welding current, while the tensile strength increased with the increase in the welding speed. No tearing or cracking was observed in either the cap twists or the root bends in the 1800 bending tests.

🔖

Bu Makaleye Atıf Yap

YÜRÜK, A. (2023). TIG kaynak parametrelerinin AISI 316L paslanmaz çeliğinin mikro yapı ve mekanik özelliklerine etkisi. Pamukkale Üniversitesi Mühendislik Bilimleri Dergisi, Cilt: 29 - Sayı: 1, 76–85. https://ajindex.com/articles/888235

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (13)

  1. Moteshakker A, Danaee I, Moeinifar S, Ashrafi A. “Hardness and tensile properties of dissimilar welds joints between SAF 2205 and AISI 316L”. Science and Technology of Welding and Joining, 21(1), 1-10, 2016
  2. Hussien AM, El-Shabasy AB, Abd El-Ghany KM. “Evaluation of stainless steel 316L joints welded by laser”. Journal Of Al-Azhar University Engineering Sector, 14(50), 229-236, 2019
  3. Subhas CM, Pradip KP, Asish B. “Design optimization of TIG welding process for AISI 316L stainless steel”. International Journal of Recent Technology and Engineering, 8(2), 5348-5354, 2019
  4. Kumar M, Punia A. “Investigation on dissimilar metal welding of stainless steel 316L and dild steel A-2062 using GTAW”. International Research Journal of Engineering and Technology, 6(8), 286-292, 2019
  5. Luis HG, Carlos ADR, Sebastião EK, Marcelo F, de O. “Corrosion behaviour of a dissimilar joint TIG weld between austenitic AISI 316L and ferritic AISI 444 stainless steels“. Welding International, 30(4), 268-276, 2016
  6. Hedayat MS, Morteza T. “Comparative study of AISI 304L to AISI 316L stainless steels joints by TIG and Nd:YAG laser welding”. Journal of Alloys and Compounds, 767, 112-121, 2018
  7. Kocabekir B, Kacar R, Gündüz S, Hayat F. “An effect of heat input, weld atmosphere and weld cooling conditions on the resistance spot weldability of 316L austenitic stainless steel”. Journal o f Materials Processing Technology, 195, 327-335, 2008
  8. Merıch C, Karabash O, Babayev Y, Demirkiran K. “An investigation of the weld region of AISI 304, AISI 316L and AISI 431 stainless steels joined by GTAW”. Journal of Qafqaz Unıversity-Mechanical And Industrıal Engineerıng, 1(1), 73-81, 2013
  9. Çınar Ö, Yaralı MC, Erdemir E, Çetiner BN, Mergen A, Güllüoğlu AN. “The similar and dissimilar TIG welding of 316L and 321 austenitic stainless steels”. ALKU Journal of Science, 1(3), 148-155, 2019
  10. Bolarinwa JK, Saliu OS, Godwin IE, Ayotunde II. “Review of GTAW welding parameters”. Journal of Minerals and Materials Characterization and Engineering, 6, 541-554, 2018
  11. Sathish T, Dinesh Kumar S, Muthukumar K, Karthick S. “Natural inspiration technique for the parameter optimization of A-GTAW welding of naval steel”. Materials Today: Proceedings, 21, 843-846, 2020
  12. Priya C, Hemant P. “A review on activated gas tungsten arc welding (A-GTAW)”. International Journal of Scientific Development and Research, 1(5), 798-803, 2016
  13. Malhotra D, Shahi AS, Gupta K. “Effect of GTAW