KaydedilenlerDerginizi ekleyin

Dergiler / European Mechanical Science / 2023 / Cilt: 7 - Sayı: 1

An experimental investigation of formability of inconel sheet plate for different die angles and rolling directions in press brake bending

Koray HAYRAT
Ergin KOSA
Şenol DURMUŞOĞLU
Sayfa
29–34
Yayın Tarihi
2023-03-20
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

It is demonstrated that cup height value has been found as 17.20 mm.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:The formability of Inconel materials is important to be used in engineering applications such as in fields of aircraft and maritime.
📊
Temel Bulgular & Veri:The aim of study is to investigate bending characteristic and formability of Inconel 625 material having a property of corrosion resistance and high strength.
💡
Sonuç & Katkı:It is demonstrated that cup height value has been found as 17.20 mm.
🔬Tür:Araştırma Makalesi
📍Kapsam:4 specimens
⚙️Değişkenler:Spring-back · Inconel · formability

Abstract

The formability of Inconel materials is important to be used in engineering applications such as in fields of aircraft and maritime. The aim of study is to investigate bending characteristic and formability of Inconel 625 material having a property of corrosion resistance and high strength. In the paper, spring-back phenomena of Inconel 625 sheets are focused on experimentally. The 4 specimens for each different die angle are prepared to be bent. The press brake is used for forming Inconel 625 sheets. The die angle is altered from 90˚ to 150˚. The different rolling direction such as 0˚ and 90˚ is chosen to investigate the effect of grain orientation on spring-back of Inconel sheets. The bending radius is constant and set as 2 mm for all bending tests. The spring-back angles and amounts are measured. Results show that as the bending angle is increased, the spring-back amount in units of angle is decreased averagely from 3.35˚ to 2.58˚ for 0˚ rolling direction and maximum spring-back angle is obtained at a die angle of 120˚ for rolling direction of 90˚. Finally, Erichsen cupping test is also applied to determine the deformability of Inconel sheets. It is demonstrated that cup height value has been found as 17.20 mm.

🔖

Bu Makaleye Atıf Yap

HAYRAT, K., KOSA, E., DURMUŞOĞLU, Ş. (2023). An experimental investigation of formability of inconel sheet plate for different die angles and rolling directions in press brake bending. European Mechanical Science, Cilt: 7 - Sayı: 1, 29–34. https://ajindex.com/articles/885941

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (1)

  1. Referans1 Alghtani, A., Brooks, P. C., Barton, D. C., Toropov, V. V. (2018). Optimisation of Important Factors Influencing Spring-back after Sheet Metal Forming. International Journal of Applied Engineering Research, 13:16027-16035. DOI:10.37622/000000. Referans 2 Fan, L. F., Gou, J., Wang, G., and Gao, Y. (2020). Springback Characteristics of Cylindrical Bending of Tailor Rolled Blanks. Advances in Materials Science Engineering, https://doi.org/10.1155/2020/9371808. Referans 3 Hai, V. G., Minh, N. T. H., and Nguyen, D. T. (2020). A study on experiment and simulation to predict the spring-back of SS400 steel sheet in large radius of V-bending process. Materials Research Express, 7(1), https://doi.org/10.1088/2053-1591/ab67f5. Referans 4 Leu, D-K., Hsieh, C-M. (2008). The influence of coining force on spring-back reduction in V-die bending process. Journal of Materials Processing Technology, 196: 230–235. https://doi.org/10.1016/j.jmatprotec.2007.05.033. Referans 5 Tong, V-C. and Nguyen, D-T. (2018). A study on spring-back in U-draw bending of DP350 high-strength steel sheets based on combined isotropic and kinematic hardening laws. Advances in Mechanical Engineering, 10(9):1–13. https://doi.org/10.1177/1687814018797436. Referans 6 Jung, J., Jun, S., Lee, H-S., Kim, B-M., Lee, M-G., and Kim, J. H. (2017). Anisotropic Hardening Behaviour and Springback of Advanced High-Strength Steels. Metals, 7:480. https://doi.org/10.3390/met7110480. Referans 7 Zhu, Y. X., Chen, W., Li, H. P., Liu, Y. L., Chen, L. (2018). Springback study of RDB of rectangular H96 tube. International Journal of Mechanical Sciences, 138–139:282–294. https://doi.org/10.1016/j.ijmecsci.2018.02.022. Referans 8 Lal, R. K., Choubey, V. K., Dwivedi, J. P., & Kumar, S. (2018). Study of factors affecting Springback in Sheet Metal Forming and Deep Drawing Process. Materials Today: Proceedings, 5: 4353–4358. https://doi.org/10.1016/j.matpr.2017.12.002. Referans 9 Chen, L., Chen, H., Guo, W., Chen, G., Wang, Q. (2014). Experimental and simulation studies of springback in rubber forming using aluminium sheet straight flanging process. Materials and Design, 54:354–360. http://dx.doi.org/10.1016/j.matdes.2013.08.050. Referans 10 Elghawail, A., Essa, K., Abosaf, M., Tolipov, A., Su, S., and Pham, D. (2017). Prediction of springback in multi-point forming. Cogent Engineering, 4(1): 1400507. https://doi.org/10.1080/23311916.2017.1400507. Referans 11 Slota, J., Gajdos, I., Spišák, E., Šiser, M. (2017). Sprin