Dergiler / Turkish Journal of Civil Engineering / 2020 / Cilt: 31 - Sayı: 1

Karma Lifli Betonların Tek Eksenli Çekme Altında Çatlak Yapısının İncelenmesi

Crack Pattern Investigation of Hybrid Fibre Reinforced Concrete under Uniaxial Tension

Sayfa
9773–9787
Yayın Tarihi
2020-01-01
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Kısa lifler arttıkça ortalama çatlak alanı belirgin bir şekilde artarken uzun liflerin miktarı arttıkça en büyük çatlak açıklığının arttığı belirlenmiştir.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Karma lifli betonların kırılmasında lif hacmi ve lif boyutunun etkisi tek eksenli çekme deneyi ile belirlenmiştir.
📊
Temel Bulgular & Veri:Kısa liflerin yalnızca tepe yükünü arttırmadığı uzun lifler ile birlikte karma olarak kullanıldığında tepe yükünden sonraki davranışa da etkiyerek tokluğu da arttırdığı görülmüştür.
💡
Sonuç & Katkı:Kısa lifler arttıkça ortalama çatlak alanı belirgin bir şekilde artarken uzun liflerin miktarı arttıkça en büyük çatlak açıklığının arttığı belirlenmiştir.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Çatlak yapısı · dijital görüntü analizi · karma lifli beton

Özet

Karma lifli betonların kırılmasında lif hacmi ve lif boyutunun etkisi tek eksenli çekme deneyi ile belirlenmiştir. Kemik şeklindeki numuneler serbest dönen mafsallı yükleme düzeneğinde tek eksenli çekme altında yüklenmiştir. Deney sonuçları lif hacmi arttıkça hem çekme dayanımının hem de yük-deplasman grafiğinin altında kalan alanın yani betonun tokluğunun arttığını göstermiştir. Kısa liflerin yalnızca tepe yükünü arttırmadığı uzun lifler ile birlikte karma olarak kullanıldığında tepe yükünden sonraki davranışa da etkiyerek tokluğu da arttırdığı görülmüştür. Görüntü analizleri karma lifli betonlarda çatlağın hiçbir zaman doğrusal olmadığını, betonun iç kısımlarına ilerledikçe dış yüzeyde görünmeyen çoklu çatlamanın, dallanma ve köprülenmenin bulunduğunu göstermiştir. Kısa lifler arttıkça ortalama çatlak alanı belirgin bir şekilde artarken uzun liflerin miktarı arttıkça en büyük çatlak açıklığının arttığı belirlenmiştir.

Abstract

The effect of size and volume of fibres on the fracture of hybrid fibre reinforced concrete was determined by applying uniaxial tensile test. The bone shaped specimens were loaded under uniaxial tension by using freely rotated support loading test setup. The test results showed that the increase in fibre volume results in an increase in both tensile strength and the area under the load displacement curve, which is the measure of the material toughness. It was shown that the use of short fibres not only increased the peak load but also affected the post-peak behaviour and increased the toughness especially when they were used together with long fibres. The image analyses pointed out that in hybrid fibre reinforced concrete the crack patterns are not in general linear. Instead, the cracks propagate inside the samples forming multiple cracks and crack branches as well as developing bridging, though these features are not observed on the surface of the samples. The results showed that with increasing amount of short fibres the average crack area was increased, while the use of long fibres in more abundance increased the width of the largest crack.

🔖

Bu Makaleye Atıf Yap

ALDANMAZ, B. A. (2020). Karma Lifli Betonların Tek Eksenli Çekme Altında Çatlak Yapısının İncelenmesi. Turkish Journal of Civil Engineering, Cilt: 31 - Sayı: 1, 9773–9787. https://ajindex.com/articles/864247

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (12)

  1. Rossi, P., Acker, P., Mallier, Y., Effect of steel fibres at two stages: the material and the structure. Mater. Struct., 20, 436-439, 1987
  2. Mobasher, B., Li, C.Y., Mechanical properties of hybrid cement-based composites. ACI Mater. J., 93(3), 284-292, 1996
  3. Yao, W., Li, J., Wu, K., Mechanical properties of hybrid fiber-reinforced concrete at low fiber volume fraction. Cem. Conc. Res., 33(1), 27-30, 2003
  4. Lawler, J.S., Wilhelm, T., Zampini, D., Shah, S.P., Fracture processes of hybrid fiber-reinforced mortar. Mater. Struct., 36(257), 197-208, 2003
  5. Banthia, N., Gupta, R., Hybrid fiber reinforced concrete (HyFRC): fiber synergy in high strength matrices. Mater. Struct., 37(274), 707-716, 2004
  6. Banthia, N., Sappakittipakorn, M., Toughness enhancement in steel fiber reinforced concrete through fiber hybridization. Cem. Conc. Res., 37(9), 1366-1372, 2007
  7. Sahmaran, M., Yaman, I.O., Hybrid fiber reinforced self-compacting concrete with a high-volume coarse fly ash. Cons. Build. Mater., 21(1), 150-156, 2007
  8. Kim, D.J., Park, S.H., Ryu, G.S., Koh, K.T., Comparative flexural behavior of Hybrid Ultra High Performance Fiber Reinforced Concrete with different macro fibers. Cons. Build. Mater., 25(11), 4144-4155, 2011
  9. Kim, D.J., Park, S.H., Ryu, G.S., Koh, K.T., Tensile behavior of Ultra High Performance Hybrid Fiber Reinforced Concrete. Cem. Conc. Compos., 34(2), 172-184, 2012
  10. Akcay, B., Tasdemir, M.A., Mechanical behaviour and fibre dispersion of hybrid steel fibre reinforced self-compacting concrete. Cons. Build. Mater., 28(1), 287-293, 2012
  11. Markovic, I., van Mier, J.G.M., Walraven, J.C., Development of high performance hybrid fibre concrete, Proceedings 4th International RILEM Workshop on High Performance Hybrid Fibre Concrete HPFRCC-4 (Naaman, A.E., Reinhardt, H.W., Eds.), RILEM Publications S.A.R.L., Bagneuax, France, Mainz, Germany, 277-300. 2003. [12] van Mier, J.G.M., Reality behind the fictitous crack?, Proceedings of International Conference on Fracture of Concrete and Concrete Structures-FraMCos 5, Evanston, Illinois, 11-30, 2004. [13] van Mier, J.G.M., Framework for a generalized four-stage fracture model of cement-based materials. Eng. Fract. Mech., 75(118), 5072–86, 2008. [14] van Vliet, M.R.A., Size effect in tensile fracture of concrete and rock, PhD Thesis, Delft University of Technology, The Netherlands, 2000
  12. Ferro, G., Effetti di scala sulla resisrenza a trazione dei materialli (Scale effects on