Dergiler / Health Sciences Quarterly / 2020 / Cilt: 4 - Sayı: 2

THE EFFECT OF THERMAL POWER PLANT FLY ASH IN GRANITE BODY ON MICROSTRUCTURE AND TECHNICAL PROPERTIES

Sayfa
147–156
Yayın Tarihi
2020-05-15
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

The ability of pressing of the sample with 10wt.% ash additive was negatively affected due to the excess amount of fine ash and so occure lamination and bloating.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:In this study 2-5-10 wt.% thermal power plant ash was added to the granite body replace feldspar to use environmental waste in the ceramic body and to reduce production costs.
📊
Temel Bulgular & Veri:After sintering, it was determined that 2 wt.% fly ash can be used in granite body.
💡
Sonuç & Katkı:The ability of pressing of the sample with 10wt.% ash additive was negatively affected due to the excess amount of fine ash and so occure lamination and bloating.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Fly ash · granite · sintering

Abstract

In this study 2-5-10 wt.% thermal power plant ash was added to the granite body replace feldspar to use environmental waste in the ceramic body and to reduce production costs. Loss on inginitions, fired bending strengths, dry strength, fired shrinkages, water absorbtion and colorimeter degrees were measured. Microstructure was determined by scanning electron microscope (SEM), energy dispersive x-ray spectrometer (Edx) and x-ray diffractometer (XRD) measurements. After sintering, it was determined that 2 wt.% fly ash can be used in granite body. In sintered body, according to XRD phase analysis, amount of free quartz and mullite decreased and albite formation was observed. While the fired strength value is 399 kg/cm2 in standard body, it is 315 kg/cm2 in 2 wt.% fly ash added body. In the experiment with 2 wt.% ash additive, according to SEM images, the number and volume of large pores increased while small pores decreased. The ability of pressing of the sample with 10wt.% ash additive was negatively affected due to the excess amount of fine ash and so occure lamination and bloating.

🔖

Bu Makaleye Atıf Yap

ELMAS, S. (2020). THE EFFECT OF THERMAL POWER PLANT FLY ASH IN GRANITE BODY ON MICROSTRUCTURE AND TECHNICAL PROPERTIES. Health Sciences Quarterly, Cilt: 4 - Sayı: 2, 147–156. https://ajindex.com/articles/836604

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (13)

  1. AMIN, Sh.K., ABDEL HAMID, E.M., EL-SHERBINY, S.A., SIBAK, H.A., ABADIR, M.F.,2018, The use of sewage sludge in the production of ceramic floor tiles, Housing a Building National Research Center (14) 309-315
  2. ASTM, C 20, Standard test methods for apparent porosity, water absorbtion, apparent specific gravity and bulk density of burned refractory brick and shapes by boiling water, Annual Book of ASTM Standards, 2000
  3. DANA, K., DAS, S., DAS, S.K., 2004, Effect of substitution of fly ash for quartz in triaxial kaolin- quartz-feldspar system, Journal of the European Ceramic Society (24) 3169-3175
  4. ELMAS, S., 2019, Using Fired Wall Tiles Scraps in Floor Tile Body, Journal of scientific perspectives Vol 3 No 2 ERCIYES, İ.T., Karo Seramik Üretim Teknolojisi, Teknik Yayınlar Serisi II, ÇİTOSAN FIGEN, A. K., ÖZÇAY, Ü., PIŞKIN, S.,2017, Manufacturing and Characterization of Roof Tiles a Mixture of Tile Waste and Coal Fly Ash, Suleyman Demirel University Journal of Natural and Applied Sciences Volume 21, Issue 1, 224-229
  5. Fortuna, Domenica,2000,
  6. Sanitaryware, İtaly JI, R., ZHANG, Z., YAN CHEN, ZHU, M., LI, Z., 2016, Preparation of novel ceramic tiles with high Al2O3 content derived from coal fly ash, Construction and Building Materials (114) 888-895
  7. KOCKAL, N.U,2012, Utilization of different types of coal fly ash in the production of ceramic tiles, Ceramica y Vidrio Vol 51, 5, 297-304,
  8. Spain LUO, Y., ZHENG, S, MA SHUHUA, LIU CHUNLI, WANG, X., 2017,Ceramic tiles derived from coal fly ash: preparation and mechanical characterization, Ceramics International (43) 11953-11966
  9. LUZ, A. P., RIBEIRO, S., 2007, Use of glass waste as a raw material in porcelain stoneware tile mixtures, Ceramic International (33) 761-765
  10. OZDEMIR, I., YILMAZ, S., 2007, Processing of unglazed ceramic tiles from blast furnace slag, Journal of Materials Processing Technology (183) 13-17
  11. OZTURK, Z. B., GULTEKIN, E. R., 2015, Preparation of ceramic wall tiling derived from blast furnace slag, Ceramic International (41) 12020-12026
  12. RICHERSON, D. W., Modern Ceramic Engineering, Properties,Processing and Use in Design 2.Edition, Marcel Deker Inc.,1992,
  13. New York TRNIK, A., STUBNA, I., SOKOLAR, R., MEDVED, I., 2013, Use of fly ash in ceramic tiles: elastic properties during firing, Journal of the Ceramic Society of Japan 121 (11) 925-929 Türkiye’deki Uçucu Küllerin Sınıflandırılması ve Özellikleri,2009, Türkiye Çimento Müstehsilleri Birliği, Ankara,Turkiye ZONG, Y., ZHANG, X., MUKIZA, E., XU XIAOXIONG, LI, F.