Dergiler / Mehmet Akif Ersoy Üniversitesi Fen Bilimleri Enstitüsü Dergisi / 2019 / Cilt: 10 - Sayı: 1

Klasik Su Verme-Temperleme Isıl İşlemine Göre Yenilikçi Su Verme-Ayrıştırma Isıl İşleminin Orta Karbonlu Çeliğin Mikroyapı ve Sertlik Özelliklerine Etkisi

Effect of Innovative Quenching-Partitioning Heat Treatment on Microstructure and Hardness Properties of Medium Carbon Steel According to Traditional Quenching-Tempering Heat Treatment

Sayfa
51–59
Yayın Tarihi
2019-07-29
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Mikroyapıda varlığı gözlemlenen kalıntı östenite rağmen su verme-ayrıştırma ısıl işlemi ile elde edilen sertlik değerlerinin, klasik su verme-temperleme ısıl işlemine göre yüksek olduğu sonucuna varılmıştır.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Çeliklerin şekillendirilebilirliği bakımından süneklik, istenen bir malzeme özelliğidir.
📊
Temel Bulgular & Veri:Bu çalışmada 0,38 karbon miktarına sahip çeliğe uygulanan su verme-temperleme ve su verme-ayrıştırma ısıl işlemlerinin mikroyapı ve sertlik özelliklerinin karşılaştırılması yapılmıştır.
💡
Sonuç & Katkı:Mikroyapıda varlığı gözlemlenen kalıntı östenite rağmen su verme-ayrıştırma ısıl işlemi ile elde edilen sertlik değerlerinin, klasik su verme-temperleme ısıl işlemine göre yüksek olduğu sonucuna varılmıştır.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Temperleme · Karbon ayrıştırma · Kalıntı östenit

Özet

Çeliklerin şekillendirilebilirliği bakımından süneklik, istenen bir malzeme özelliğidir. Sanayide sıkça kullanılan bir işlem olan klasik su verme-temperleme ısıl işlemi ile istenilen sünekliğin elde edilmesi mümkündür. Fakat sünekliğin artmasıyla çeliğin sertliğinin azalması istenmeyen bir etkendir. Yenilikçi su verme-ayrıştırma ısıl işlemi ile süneklik ve mukavemetin iyi bir kombinasyonunun elde edilmesi amaçlanmaktadır. Bu çalışmada 0,38 karbon miktarına sahip çeliğe uygulanan su verme-temperleme ve su verme-ayrıştırma ısıl işlemlerinin mikroyapı ve sertlik özelliklerinin karşılaştırılması yapılmıştır. Mikroyapıda varlığı gözlemlenen kalıntı östenite rağmen su verme-ayrıştırma ısıl işlemi ile elde edilen sertlik değerlerinin, klasik su verme-temperleme ısıl işlemine göre yüksek olduğu sonucuna varılmıştır.

Abstract

Ductility in the formability of the steels is the desired material property. It is possible to obtain the desired ductility by the traditional quenching-tempering heat treatment which is often used in industry. However, decreasing the hardness of steel with increasing ductility is an undesirable factor. It is aimed to obtain a good combination of ductility and strength with the innovative quenching-partitioning heat treatment. In this study, microstructure and hardness properties of quenching-tempering and quenching-partitioning heat treatments applied to steel having 0.38 carbon content were compared. Despite the retained austenite observed in the microstructure, it was concluded that the hardness values obtained by the quenching-partitioning heat treatment were higher than the traditional quenching-tempering heat treatment.

🔖

Bu Makaleye Atıf Yap

İŞYARLAR, M. Ş., GÜL, F. (2019). Klasik Su Verme-Temperleme Isıl İşlemine Göre Yenilikçi Su Verme-Ayrıştırma Isıl İşleminin Orta Karbonlu Çeliğin Mikroyapı ve Sertlik Özelliklerine Etkisi. Mehmet Akif Ersoy Üniversitesi Fen Bilimleri Enstitüsü Dergisi, Cilt: 10 - Sayı: 1, 51–59. https://ajindex.com/articles/790192

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (7)

  1. Arlazarov, A., Bouaziz, O., Masse, J. P., & Kegel, F. (2015). Characterization and modeling of mechanical behavior of quenching and partitioning steels. Materials Science and Engineering: A 620: 293-300.
  2. Bagliani, E. P., Santofimia, M. J., Zhao, L., Sietsma, J., & Anelli, E. (2013). Microstructure, tensile and toughness properties after quenching and partitioning treatments of a medium-carbon steel. Materials Science and Engineering: A 559: 486-495.
  3. Chipalkatti, J. (1999). Modeling of Austenite Decomposition in an AISI 4140 Steel. Doctoral Dissertation, University of British Columbia. De Diego Calderón, M. I. (2015). Mechanical Properties of Advanced High-Strength Steels Produced via Quenching And Partitioning. Doctoral Dissertation, Universidad Carlos III de Madrid. De Diego-Calderón, I., De Knijf, D., Monclús, M. A., Molina-Aldareguia, J. M., Sabirov, I., Föjer, C., & Petrov, R. H. (2015). Global and local deformation behavior and mechanical properties of individual phases in a quenched and partitioned steel. Materials Science and Engineering: A 630: 27-35.
  4. Digges, T. G., Rosenberg, S. J., & Geil, G. W. (1966). Heat Treatment and Properties of Iron and Steel. Natıonal Bureau of Standards Gaıthersburg Md. Dong, H. Y., Wu, K. M., Wang, X. L., Hou, T. P., & Yan, R. (2018). A comparative study on the three-body abrasive wear performance of Q&P processing and low-temperature bainitic transformation for a medium-carbon dual-phase steel, Wear 402: 21-29.Edmonds, D. V., He, K., Rizzo, F. C., De Cooman, B. C., Matlock, D. K., & Speer, J. G. (2006). Quenching and partitioning martensite—A novel steel heat treatment. Materials Science and Engineering: A 438: 25-34.
  5. Gao, G., Zhang, H., Tan, Z., Liu, W., & Bai, B. (2013). A carbide-free bainite/martensite/austenite triplex steel with enhanced mechanical properties treated by a novel quenching–partitioning–tempering process. Materials Science and Engineering: A 559: 165-169.
  6. HajyAkbary, F., Sietsma, J., Miyamoto, G., Furuhara, T., & Santofimia, M. J. (2016). Interaction of carbon partitioning, carbide precipitation and bainite formation during the Q&P process in a low C steel. Acta Materialia 104: 72-83.
  7. Hao, Q., Qin, S., Liu, Y., Zuo, X., Chen, N., Huang, W., & Rong, Y. (2016). Effect of retained austenite on the dynamic tensile behavior of a novel quenching-partitioning-tempering martensitic steel. Materials Science and Engineering: A 662: 16-25. Hauserová, D., Nový, Z., Dlouhý, J., & Motyčka, P. (2011). Q-P process