Dergiler / İmalat Teknolojileri ve Uygulamaları / 2020 / Cilt: 1 - Sayı: 2

Modelling and Optimization of Burr Height in Fiber Laser Drilling of Ferritic Stainless Steel

Sayfa
32–39
Yayın Tarihi
2020-08-26
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

The R2 value of Bh model obtained by response surface method indicated a robust relationship in high level between the machining parameters and response.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Laser drilling is the nontraditional machining methods that provides the machining of sheet metal parts with high precision and complex geometry.
📊
Temel Bulgular & Veri:In laser drilling, the main parameters such as the focal point, gas pressure and feed rate directly affecting the cutting process play important role on the quality characteristics of the part.
💡
Sonuç & Katkı:The R2 value of Bh model obtained by response surface method indicated a robust relationship in high level between the machining parameters and response.
🔬Tür:Modelleme & Sayısal Simülasyon
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Laser drilling · Stainless steel · Burr height

Abstract

Laser drilling is the nontraditional machining methods that provides the machining of sheet metal parts with high precision and complex geometry. In laser drilling, the main parameters such as the focal point, gas pressure and feed rate directly affecting the cutting process play important role on the quality characteristics of the part. These parameters significantly influence the main machining outputs or responses such as burr formation and hole quality as well as the machining productivity. Thus, it is important to determine the ideal machining parameters during laser drilling, especially in terms of minimum burr formation. In this study, burr formation during laser drilling of ferritic stainless steel was analyzed in detail and mathematical model of burr height (Bh) was developed. Drilling operations were performed at three different focal point, gas pressure and feed rate. According to the experimental results, the smallest Bh value was obtained with focal point of -5, feed rate of 1200 mm/min and gas pressure of 12 bar. Based on analysis of variance, the most important parameter for burr height was found as the feed speed with 38.71%. The cutting parameters, statistically, were evaluated for the burr height. The R2 value of Bh model obtained by response surface method indicated a robust relationship in high level between the machining parameters and response.

🔖

Bu Makaleye Atıf Yap

UZUN, H., MERAL, T., GÜNAY, M. (2020). Modelling and Optimization of Burr Height in Fiber Laser Drilling of Ferritic Stainless Steel. İmalat Teknolojileri ve Uygulamaları, Cilt: 1 - Sayı: 2, 32–39. https://ajindex.com/articles/770311

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (13)

  1. A.M. Pak, M. Moradi, Hole geometry features analysis in fiber laser percussion drilling process, International Journal of Advances in Mechanical and Automobile Engineering, 2(1): 18-21, 2015
  2. B.S. Yilbas, Laser Drilling Practical Applications, Springer, Berlin, 2013
  3. K. Jarosz, P. Löschner, P. Nieslony, Effect of cutting speed surface quality and heat-affected zone in laser cutting of 316L stainless steel, International Conference on Manufacturing Engineering and Materials, 6-10 June 2016, NovýSmokovec
  4. M. Taskin, U. Caligulu, The effect on the joining of welding power on the laser welding of couple steels AISI 430/1010, Firat University Journal of Engineering Science, 21(1): 11-22, 2009
  5. N. Fujita, K. Ohmura, A. Yamamoto, Changes of microstructures and high temperature properties during high temperature service of Niobium added ferritic stainless steels. Material Science and Engineering A, 351(1-2): 272-281, 2003
  6. J.C. Aurich, D. Dornfeld, P.J. Arrazola, V. Franke, L. Leitz, S. Min., Burrs-Analysis, control and removal, CIRP Annals, 58(2): 519-542, 2009
  7. H. Ozaki, Y. Koike, H. Kawakami, J. Suzuki, Cutting properties of austenitic stainless steel by using laser cutting process without assist gas, Hindawi Publishing Corporation Advances in Optical Technologies, 1-8, 2012
  8. D.J. Kotodiya, D.H. Pandya, Parametric analysis of laser machining with response surface method on SS-304, Procedia Technology, 23:376-382, 2016
  9. C. Wandera, V. Kujanpaa Optimization of parameters for fibre laser cutting of a 10 mm stainless steel plate, Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 225:641-649, 2011
  10. S. Chatterjee, K. Abhishek, S.S. Mahapatra, Study on surface quality of laser drilled holes: parametric optimization using harmony search algorithm, International Journal of Materials, Mechanics and Manufacturing, 5(4): 251-254 2017
  11. J. Petru, T. Zlamal, R. Cep, K. Monkova, P. Monka, Influence of cutting parameters on heat-affected zone after laser cutting, Tehnicki Vjesnik, 20(2): 225-230, 2013
  12. M. Moradi, E. Golchin, Investigation on the effects of process parameters on laser percussion drilling using finite element methodology; statistical modelling and optimization, Latin American Journal of Solids and Structures, 14: 464-484, 2017
  13. Y.R. Satpute, K.H. Inamdar, An investigation of CO2 laser drilling, Journal of Emerging Technologies and Innovative Research, 6(3): 124-128, 2016.