KaydedilenlerDerginizi ekleyin

Dergiler / Eurasian Journal of Science Engineering and Technology / 2021 / Cilt: 2 - Sayı: 1

INVESTIGATION OF THE EFFECT OF HEATING RAMPING RATE ON Cu(In, Ga)Te2 THIN FILMS

Serkan ERKAN
Yavuz ATASOY
Ali ÇİRİŞ
Emin BACAKSIZ
Sayfa
10–17
Yayın Tarihi
2021-06-03
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

It was concluded that CIGT thin film reacted with a ramping rate of 5°C/sec had superior properties compared to other samples.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Cu(In,Ga)Te2 (CIGT) thin films were grown using a two-stage method.
📊
Temel Bulgular & Veri:In the first stage, (Cu, In, Ga) precursor layers were grown on Mo coated flexible stainless steel substrates using the electro-deposition method.
💡
Sonuç & Katkı:It was concluded that CIGT thin film reacted with a ramping rate of 5°C/sec had superior properties compared to other samples.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Cu(In · Ga)Te2 · heating ramping rate

Abstract

Cu(In,Ga)Te2 (CIGT) thin films were grown using a two-stage method. In the first stage, (Cu, In, Ga) precursor layers were grown on Mo coated flexible stainless steel substrates using the electro-deposition method. NaF and Te layers were grown on metallic precursor layers using electron beam evaporation method. In the second stage, the foil/Mo/(Cu, In, Ga)/NaF/Te stacks were reacted at 600°C for 5 minutes by rapid thermal processing. The temperature ramping rates in this procedure were 0.5°C/sec, 1°C/sec, 5°C/sec and 10°C/sec. In order to investigate the effect of temperature ramping rate on the structural properties of CIGT thin films, XRD, Raman, SEM and EDS measurements were performed. Regardless of the ramping rates, it was determined that all samples crystallized in chalcopyrite structure. According to the Raman spectra, as the ramping rate increased, position of the A1 mode completely changed and shifted from 127 cm-1 to 135 cm-1 due to bond-stretching forces between the nearest-neighbor atoms. It was concluded that CIGT thin film reacted with a ramping rate of 5°C/sec had superior properties compared to other samples.

🔖

Bu Makaleye Atıf Yap

ERKAN, S., ATASOY, Y., ÇİRİŞ, A., BACAKSIZ, E. (2021). INVESTIGATION OF THE EFFECT OF HEATING RAMPING RATE ON Cu(In, Ga)Te2 THIN FILMS. Eurasian Journal of Science Engineering and Technology, Cilt: 2 - Sayı: 1, 10–17. https://ajindex.com/articles/756344

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (14)

  1. Calixto, M., et al., Compositional and optoelectronic properties of CIS and CIGS thin films formed by electrodeposition. Solar energy materials and solar cells, 1999. 59(1-2): p. 75-84.
  2. Fernandez, A., et al., Electrodeposited and selenized (CuInSe2)(CIS) thin films for photovoltaic applications. Solar Energy Materials and Solar Cells, 1998. 52(3-4): p. 423-431.
  3. Gordillo, G. and C. Calderon, CIS thin film solar cells with evaporated InSe buffer layers. Solar energy materials and solar cells, 2003. 77(2): p. 163-173.
  4. Zaretskaya, E., et al., Raman spectroscopy of CuInSe2 thin films prepared by selenization. Journal of Physics and Chemistry of Solids, 2003. 64(9-10): p. 1989-1993.
  5. Caballero, R., et al. CGS-thin films solar cells on transparent back contact. in 2006 IEEE 4th World Conference on Photovoltaic Energy Conference. 2006.
  6. IEEE. Ishizuka, S., et al., Structural tuning of wide‐gap chalcopyrite CuGaSe2 thin films and highly efficient solar cells: differences from narrow‐gap Cu (In, Ga) Se2. Progress in Photovoltaics: Research and Applications, 2014. 22(7): p. 821-829.
  7. Thirumalaisamy, L., et al., Engineering of sub-band in CuGaS2 thin films via Mo doping by chemical spray pyrolysis route. Thin Solid Films, 2020. 709: p. 138252. Aissaoui, O., et al., Study of flash evaporated CuIn1− xGaxTe2 (x= 0, 0.5 and 1) thin films. Thin Solid Films, 2009. 517(7): p. 2171-2174.
  8. Jung, S., et al., Effects of Ga contents on properties of CIGS thin films and solar cells fabricated by co-evaporation technique. Current Applied Physics, 2010. 10(4): p. 990-996.
  9. Li, W., et al., Fabrication of Cu (In, Ga) Se2 thin films solar cell by selenization process with Se vapor. Solar Energy, 2006. 80(2): p. 191-195.
  10. Zhou, D., et al., Sputtered molybdenum thin films and the application in CIGS solar cells. Applied Surface Science, 2016. 362: p. 202-209.
  11. Green, M.A., et al., Solar cell efficiency tables (Version 45). Progress in photovoltaics: research and applications, 2015. 23(1): p. 1-9.
  12. Kato, T., et al., Record efficiency for thin-film polycrystalline solar cells up to 22.9% achieved by Cs-treated Cu (In, Ga)(Se, S) 2. IEEE Journal of Photovoltaics, 2018. 9(1): p. 325-330.
  13. Karatay, A., et al., The effect of Se/Te ratio on transient absorption behavior and nonlinear absorption properties of CuIn0. 7Ga0. 3 (Se1− xTex) 2 (0≤ x≤ 1) amorphous semiconductor thin films. Optical Materials, 2017. 73: p. 20-24.
  14. Gremenok, V., et al., Characterization of polycrystalline Cu (In, Ga) Te2 thin films