Dergiler / Turkish Journal of Engineering / 2017 / Cilt: 1 - Sayı: 1

THE OPTIMIZATION OF SURFACE ROUGHNESS OF AZ91D MAGNESIUM ALLOY USING ANOVA IN BALL BURNISHING PROCESS

Sayfa
25–31
Yayın Tarihi
2017-05-15
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

The main results of the statistical analysis highlight the great influence of the feed rate, burnishing force and number of passes on surface roughness among the set of factors and their interactions considered.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Ball burnishing is a simple, cost-effective and fast finishing process generally applied to better the surface roughness of machine parts.
📊
Temel Bulgular & Veri:In this study, the Taguchi L18 orthogonal array method is used to find the optimal surface roughness in ball burnishing of AZ91D magnesium alloy.
💡
Sonuç & Katkı:The main results of the statistical analysis highlight the great influence of the feed rate, burnishing force and number of passes on surface roughness among the set of factors and their interactions considered.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Surface roughness · Taguchi method · Ball burnishing

Abstract

Ball burnishing is a simple, cost-effective and fast finishing process generally applied to better the surface roughness of machine parts. In this study, the Taguchi L18 orthogonal array method is used to find the optimal surface roughness in ball burnishing of AZ91D magnesium alloy. The orthogonal array, the signal-to-noise ratio, and ANOVA (analysis of variance) method is employed to study the performance characteristics in ball burnishing process of AZ91D alloy bars. The purpose of this study is to perform an ANOVA to determine the effects of the (burnishing force, burnishing speed, feed rate and number of passes parameters) on the surface roughness data obtained after the ball burnishing applied to the AZ91D bars. The optimum burnishing parameter was determined based on signal-to-noise (S/N) ratio. Data was analyzed by means of the ANOVA method. The main results of the statistical analysis highlight the great influence of the feed rate, burnishing force and number of passes on surface roughness among the set of factors and their interactions considered.

🔖

Bu Makaleye Atıf Yap

BULDUM, B. B., CAGAN, S. C. (2017). THE OPTIMIZATION OF SURFACE ROUGHNESS OF AZ91D MAGNESIUM ALLOY USING ANOVA IN BALL BURNISHING PROCESS. Turkish Journal of Engineering, Cilt: 1 - Sayı: 1, 25–31. https://ajindex.com/articles/705085

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (13)

  1. Buldum, B.B. (2013). Analyzing the Machinability of Magnesium Alloy. AZ91. PhD Thesis, Gazi University, Ankara,
  2. Turkey. Buldum, B.B., Sik, A., Ozkul, I. (2013) “Investigation of magnesium alloys machinability.” International Journal of Electronics, Mechanical and Mechatronics Engineering, Vol. 2, pp. 261-268.
  3. Carou, D., Rubio, E.M., Lauro, C.H., Davim J P. (2014). “Experimental investigation on surface finish during intermittent turning of UNS M11917 magnesium alloy under dry and near dry machining conditions.” Measurement, Vol. 56, pp.136-154.
  4. Cicek, A., Kivak, T., Ekici, E. (2015). “Optimization of drilling parameters using taguchi technique and response surface methodology (RSM) in drilling of AISI 304 steel with cryogenically treated HSS drills.” Journal of Intelligent Manufacturing, Vol. 26, pp. 295-305.
  5. Dabeer, P.S., Purohit, G.K. (2010). “Effect of ball burnishing parameters on surface roughness using surface roughness methodology.” Advances in Production & Management, Vol. 5, pp. 111-116.
  6. El-Axir, M.H., Othman, O.M., Abodiena, A.M. (2008). “Improvements in out-of-roundness and microhardness of inner surfaces by internal ball burnishing process.” Journal of Materials Processing Technology, Vol. 196, pp. 120-128.
  7. Esme, U. (2010). “Use of grey based taguchi method in ball burnishing process for the optimization of surface roughness and microhardness of AA 7075 aluminum alloy.” Materials and Technology, vol. 44, pp. 129-135.
  8. El-Taweel, T.A., El-Axir, M.H. (2009). “Analysis and optimization of the ball burnishing process through the taguchi technique.” The International Journal of Advanced Manufacturing Technology, Vol. 41, pp. 301-310.
  9. Gaitonde, V.N., Karnik, S.R., Achyutha, B.T., Siddeswarappa, B. (2006). “Multi-response optimization in drilling using taguchi’s quality loss function.” Indian Journal of Engineering and Materials Sciences, Vol. 13, pp. 484-488.
  10. Gnedenkov, A.S., Sinebryukhov, S.L., Mashtalyar, D.V., Gnedenkov, S.V. (2013) “Features of the corrosion processes development at the magnesium alloys surface.” Surface & Coating Technology, Vol. 225, 112-118.
  11. Gokce, B. (2015) “Analysis of wear behaviours of borided 440C steels by using taguchi method.” Journal of the Balkan Tribological Association, Vol. 21, pp. 831-841.
  12. Grzesik W, Zak K. (2012) “Modification of surface finish produced by hard turning using superfinishing and burnishing operations.” Journal of Materials Processing Technology, Vol. 212, pp. 315-322.
  13. Hamamci, M., Topal, E.S. (2014).