KaydedilenlerDerginizi ekleyin

Dergiler / Turkish Journal of Engineering / 2023 / Cilt: 7 - Sayı: 2

Determination of optimum design parameters of glow plug and experimental verification

Muciz ÖZCAN
M. Fahri ÜNLERŞEN
Mehmet ŞEN
Sayfa
125–133
Yayın Tarihi
2023-04-15
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Currently the whole glow plug must be changed at the end of lifetime, with our improvement only the inner tube resistance can be easily changed involving a cost reduction by about 60%.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:In Diesel Engines, the heat energy obtained from the glow plug increases the engine's ability to start up in cold climatic conditions and significantly reduces emissions of harmful gases leaving the exhaust.
📊
Temel Bulgular & Veri:In cold climatic conditions, before the start off of diesel vehicles it is necessary to wait for about 10 s the cylinder block heating.
💡
Sonuç & Katkı:Currently the whole glow plug must be changed at the end of lifetime, with our improvement only the inner tube resistance can be easily changed involving a cost reduction by about 60%.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Glow plug · Mutually inductance · Resistive element

Abstract

In Diesel Engines, the heat energy obtained from the glow plug increases the engine's ability to start up in cold climatic conditions and significantly reduces emissions of harmful gases leaving the exhaust. In cold climatic conditions, before the start off of diesel vehicles it is necessary to wait for about 10 s the cylinder block heating. This period negatively affects driving comfort. In this study, the mathematical results of the processes to optimize the time required for the glow plug to reach the required temperature have been experimentally proven. A test apparatus was developed to confirm experimentally the theoretical results. Thanks to these improvements concerning the manufacture of the glow plug, the time period to reach 850 ° C has been reduced by approximately 5 s. The proposed design is in accordance with the glow plug present in the market. Currently the whole glow plug must be changed at the end of lifetime, with our improvement only the inner tube resistance can be easily changed involving a cost reduction by about 60%.

🔖

Bu Makaleye Atıf Yap

ÖZCAN, M., ÜNLERŞEN, M. F., ŞEN, M. (2023). Determination of optimum design parameters of glow plug and experimental verification. Turkish Journal of Engineering, Cilt: 7 - Sayı: 2, 125–133. https://ajindex.com/articles/705016

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (11)

  1. Özcan, M., & Günay, H. (2013). Control of diesel engines mounted on vehicles in mobile cranes via CAN bus. Turkish Journal of Electrical Engineering and Computer Science, 21(Sup. 2), 2181-2190.
  2. Siskos, P., Capros, P., & De Vita, A. (2015). CO2 and energy efficiency car standards in the EU in the context of a decarbonisation strategy: A model-based policy assessment. Energy Policy, 84, 22-34.
  3. Peng, B. B., Fan, Y., & Xu, J. H. (2016). Integrated assessment of energy efficiency technologies and CO2 abatement cost curves in China’s road passenger car sector. Energy conversion and management, 109, 195-212.
  4. Last, B., Houben, H., Rottner, M., & Stotz, I. (2008, March). Influence of modern diesel cold start systems on the cold start, warm-up and emissions of diesel engines. Paper presented in Proceedings of the 8th Stuttgart International Symposium, Stuttgart, Germany. Weilenmann, M., Favez, J. Y., & Alvarez, R. (2009). Cold-start emissions of modern passenger cars at different low ambient temperatures and their evolution over vehicle legislation categories. Atmospheric environment, 43(15), 2419-2429.
  5. Qi, D. H., Bian, Y. Z., Ma, Z. Y., Zhang, C. H., & Liu, S. Q. (2007). Combustion and exhaust emission characteristics of a compression ignition engine using liquefied petroleum gas–diesel blended fuel. Energy conversion and management, 48(2), 500-509.
  6. Kökkülünk, G., Akdoğan, E., & Ayhan, V. (2013). Prediction of emissions and exhaust temperature for direct injection diesel engine with emulsified fuel using ANN. Turkish Journal of Electrical Engineering & Computer Sciences, 21(Sup. 2), 2141-2152.
  7. Mrzljak, V., Medica, V., & Bukovac, O. (2017). Quasi-dimensional diesel engine model with direct calculation of cylinder temperature and pressure. Tehnički vjesnik, 24 (3), 681-686. https://doi.org/10.17559/TV-20151116115801.
  8. He, B. Q. (2016). Advances in emission characteristics of diesel engines using different biodiesel fuels. Renewable and Sustainable Energy Reviews, 60, 570-586.
  9. Barna, L., & Lelea, D. (2017). Low pressure injection of oxyhydrogen in turbocharged compression ignition engines. Tehnički vjesnik, 24 (Supplement 2), 287-294. https://doi.org/10.17559/TV-20150921183805.
  10. Payri, F., Broatch, A., Salavert, J. M., & Martín, J. (2010). Investigation of Diesel combustion using multiple injection strategies for idling after cold start of passenger-car engines. Experimental Thermal and Fluid Science, 34(7), 857-865
  11. Endiz, M. S., Özcan, M., Erişmiş, M. A., Yağcı, M., &