KaydedilenlerDerginizi ekleyin

Dergiler / Tekstil ve Konfeksiyon / 2022 / Cilt: 32 - Sayı: 2

Investigation of Performance Characteristics of 3D Printing Textiles in Terms of Design and Material

Fatma BULAT
Fatma Nur BAŞARAN
Sayfa
162–172
Yayın Tarihi
2022-06-30
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Consequently, although the performances of 3D textiles get the better of one another, their breaking and bursting strengths are found to be lower than the conventional fabrics

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:New technologies that are used in the producing and processing of textile surfaces provide significant advantages for the designer.
📊
Temel Bulgular & Veri:One of the important technologies that offer today’s design advantage is three-dimensional “3D” printers.
💡
Sonuç & Katkı:Consequently, although the performances of 3D textiles get the better of one another, their breaking and bursting strengths are found to be lower than the conventional fabrics
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:3D printing · Textile Design · Fashion Design

Abstract

New technologies that are used in the producing and processing of textile surfaces provide significant advantages for the designer. One of the important technologies that offer today’s design advantage is three-dimensional “3D” printers. In this research, textile surfaces were produced with 3D printers and the performance characteristics of these surfaces were tried to be determined. Significant differences were observed in the performance of textiles based on the breaking, bursting and weight determination tests. These differences were discussed in terms of the design’s structural characteristics, material and the ways of 3D printing to stacking material. Consequently, although the performances of 3D textiles get the better of one another, their breaking and bursting strengths are found to be lower than the conventional fabrics

🔖

Bu Makaleye Atıf Yap

BULAT, F., BAŞARAN, F. N. (2022). Investigation of Performance Characteristics of 3D Printing Textiles in Terms of Design and Material. Tekstil ve Konfeksiyon, Cilt: 32 - Sayı: 2, 162–172. https://ajindex.com/articles/703205

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (3)

  1. Referans1. Hearle, J.W.S. (2015). Mechanical Properties Of Textile Reinforcements For CompositesAdvances In Composites Manufacturing And Process Design. Woodhead Publishing. Referans2. Tobler-Rohr,M.I. (2011). Handbook of sustainable textile production, Woodhead Publishing Referans3. Bulat, F., & Başaran, F.N. (2018). Tekstil Tasarımında Yenilikçi Yaklaşımlar: 3B Yazıcılarla Deneysel Çalışmalar [Innovative Approaches in Textile Design: Experimental Practices With 3d Printers]. The Journal of Kesit Academy,4(14), 257-273 Referans4. Önlü, N. (2004).
  2. Tasarımda Yaratıcılık ve İşlevsellik, Tekstil Tasarımındaki Konumu [Creativity and Functionality in Design, Its Position in Textile Design]. Atatürk University Social Sciences Institute Journal, 3(1), 86. Referans5. Meriç, D., & Üreyen, M. E. (2019). Akıllı Tekstil Malzemelerinin Tekstil ve Moda Tasarımına Katkıları [Contribution of Smart Textile Materials to Textile and Fashion Design], International Social Sciences Studies Journal, 5(30), 535-545. Referans6. Gürcüm, H. B., & Bulat, F. (2016). Tekstil Tasarımında İnovatif Bir Yaratıcılık Aracı Olarak Lazer Kesim [Laser Cutting as An Innovative Creativity Tool in Textile Design], Idil Journal of Art and Language, 6(28), 107-130. Referans7. Leigh, SJ., Bradley, RJ., Purssell, CP., Billson, DR., & Hutchins, DA. (2012).
  3. A Simple, Low-Cost Conductive Composite Material for 3D Printing of Electronic Sensors. PLOS ONE 7(11), 1-14. Referans8. Lehmann, A., Ehrmann, A., & Finsterbusch, K. (2017). Optimization Of 3D Printing with Flexible Materials. International textile conference, Stuttgart. Referans9. Cali, J., Calian, A.D., Amati, C., Kleinberger, R., Steed, A., Kautz, J., & Weyrich, T. (2012). 3D-Printing of Non-Assembly, Articulated Models. ACM Transactions on Graphics (TOG)- Proceedings of ACM, Siggrapy Asia, 31(6), 1-8. Referans10. Kim, H., Park, E., Kim, S., Park, B., Kim, N., & Lee, S. (2017). Experimental Study on Mechanical Properties of Single- and Dual-Material 3D Printed Products. Elsevier B.V. Procedia Manufacturing, 10, 887-897. Referans11. Çelik, İ. Karakoç, F., Çakır, C.M., & Duysak, A. (2013). Hızlı Prototipleme Teknolojileri ve Uygulama Alanları [Rapid Prototyping Technologies and Application Areas]. Journal of Science and Technology of Dumlupınar University, 31, 53-70. Referans12. Özsoy, K., & Duman, B. (2017). Eklemeli İmalat (3 Boyutlu Baskı) Teknolojilerinin Eğitimde Kullanılabilirliği [Usability of Additive Manufacturing (3D Printing) Technologie