Dergiler / International Journal of Thermodynamics / 2022 / Cilt: 25 - Sayı: 1

Mathematical Modeling of Waste Engine Oil Gasification for Synthesis Gas Production; Operating Parameters and Simulation

Sayfa
65–77
Yayın Tarihi
2022-03-01
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

The H2:CO ratio decreases from 1.6 to 0.6 with increasing equivalence ratio and increases from 1.2 to 1.6 with changes in oxygen enrichment.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:The release of waste oil into the environment will have destructive effects.
📊
Temel Bulgular & Veri:Thermochemical equilibrium modeling has been used in this method to predict the performance of a downdraft gasifier.
💡
Sonuç & Katkı:The H2:CO ratio decreases from 1.6 to 0.6 with increasing equivalence ratio and increases from 1.2 to 1.6 with changes in oxygen enrichment.
🔬Tür:Modelleme & Sayısal Simülasyon
📍Kapsam:2000 Verileri
⚙️Değişkenler:Gasification · Waste Engine Oil · Chemical Equilibrium

Abstract

The release of waste oil into the environment will have destructive effects. Gasification is an advanced and environmentally friendly process for converting waste oils into clean combustible gas products. Thermochemical equilibrium modeling has been used in this method to predict the performance of a downdraft gasifier. This model uses the thermodynamic equilibrium of gasification reactions to predict the gases produced in the gas mixture. Having the percentage of gas components produced, different characteristics of the produced gas including H2:CO ratio, process temperature and calorific value of the produced gas, Cold gas efficiencies and carbon conversion efficiency are also obtained. The effect of equivalence ratio, oxygen enrichment and pressure on gasification properties is analyzed. The simulation results are compared with the reported experimental measurements through which the numerical model is confirmed. The results indicated that the equivalence ratio (mole of air in gasification per mole of air in combustion) between 0.4 and 0.42 had the potential to yield the highest calorific value about 10.5 Mj.m-3. The temperature of gaseous mixture in this range will be 2000 K that can be used for other processes such as steam generation. Using pure oxygen instead of air reduces the efficiency of the gasifier from 78% to 55%. Pressure changes from 10 to 65 bar cause gas mixture temperature changes from 1684 to 1690 Kelvin. The H2:CO ratio decreases from 1.6 to 0.6 with increasing equivalence ratio and increases from 1.2 to 1.6 with changes in oxygen enrichment.

🔖

Bu Makaleye Atıf Yap

MOUSAZADE, M. R., SEDİGHİ, M., MANESH, M. H. K., GHASEMİ, M. (2022). Mathematical Modeling of Waste Engine Oil Gasification for Synthesis Gas Production; Operating Parameters and Simulation. International Journal of Thermodynamics, Cilt: 25 - Sayı: 1, 65–77. https://ajindex.com/articles/673387

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (8)

  1. M. N. Nasim, M. Sohail, B. Ravindra, V. J. J. o. M. Lotia, and C. Engineering, "Recycling waste automotive engine oil as alternative fuel for diesel engine: A review," pp. 46-50, 2014. K. K. Ramasamy and T. J. C. T. Ali, "Hydrogen production from used lubricating oils," vol. 129, no. 3-4, pp. 365-371, 2007.
  2. M. Fuentes, R. Font, M. Gómez-Rico, I. J. J. o. A. Martín-Gullón, and A. Pyrolysis, "Pyrolysis and combustion of waste lubricant oil from diesel cars: Decomposition and pollutants," vol. 79, no. 1-2, pp. 215-226, 2007.
  3. M. Rosli, F. Yee, and S. S. Tea, "Modeling and simulation of used lubricant oil re-refining process," in 2nd World Engineering Congress, Sarawak, Malaysia, 2002. N. Selukar and S. J. I. J. o. A. C. Wagh, "Gasoline and diesel synthesis from waste lubricating oil: A kinetic approach," pp. 22-25, 2014.
  4. F. C.-Y. Wang, L. J. E. Zhang, and fuels, "Chemical composition of group II lubricant oil studied by high-resolution gas chromatography and comprehensive two-dimensional gas chromatography," vol. 21, no. 6, pp. 3477-3483, 2007.
  5. E. M. Fujita, D. E. Campbell, and B. J. F. R. Zielinska, Desert Research Institute, Reno, Nevada, USA, "Chemical analysis of lubrication oil samples from a study to characterize exhaust emissions from light-duty gasoline vehicles in the Kansas City Metropolitan Area," 2006.
  6. J. Moore, S. Cui, P. Cummings, and H. J. A. I. o. C. E. A. J. Cochran, "Lubricant characterization by molecular simulation," vol. 43, no. 12, p. 3260, 1997.
  7. J. Sharaf, B. Mishra, R. J. I. J. o. E. R. Sharma, and Applications, "Production of gasoline-like fuel obtained from waste lubrication oil and its physicochemical properties," vol. 3, no. 3, pp. 113-118, 2013. S. S. Lam et al., "Progress in waste oil to sustainable energy, with emphasis on pyrolysis techniques," vol. 53, pp. 741-753, 2016.
  8. M. Puig-Arnavat, J. C. Bruno, A. J. E. Coronas, and Fuels, "Modified thermodynamic equilibrium model for biomass gasification: a study of the influence of operating conditions," vol. 26, no. 2, pp. 1385-1394, 2012. M. Puig Arnavat, "Performance modelling and validation of biomass gasifiers for trigeneration plants," Universitat Rovira i Virgili, 2011. L. Chanphavong and Z. J. J. o. t. E. I. Zainal, "Characterization and challenge of development of producer gas fuel combustor: A review," vol. 92, no. 5, pp. 1577-1590, 2019. G. Gautam, "Parametric study of a commercial-scale biomass downdraft gasifier: experiments and equilibrium modeling," 2010. C. Higman and M.