Dergiler / International Journal of 3D Printing Technologies and Digital Industry / 2021 / Cilt: 5 - Sayı: 3

ANALYTICAL AND NUMERICAL INVESTIGATION OF ELASTIC STRESSES IN THERMOPLASTIC MATRIX COMPOSITE DISCS UNDER TEMPERATURE EFFECT

Sayfa
730–741
Yayın Tarihi
2021-12-30
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

The purpose of this article is to study the behavior of the thermal load on two different thermoplastic disks.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:In this study, elastic stress analysis was performed on thermoplastic composite discs.
📊
Temel Bulgular & Veri:Under the parabolic temperature distribution of the disks, radial stresses formed on the inner and outer parts of the disks were calculated by assuming that the modulus of elasticity does not change with temperature at temperatures of 30 °C, 60 °C, 90 °C, 120 °C on the inner and outer surfaces of the disk.
💡
Sonuç & Katkı:The purpose of this article is to study the behavior of the thermal load on two different thermoplastic disks.
🔬Tür:Modelleme & Sayısal Simülasyon
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Thermoplastic disc · Elastic stress analysis · Modulus of elasticity

Özet

In this study, elastic stress analysis was performed on thermoplastic composite discs. The modulus of elasticity of thermoplastic composite discs is also different from each other. Our goal is to study elastic stretching. The field of application of primitive stresses caused by uneven temperature distribution in engineering is quite large. Under the parabolic temperature distribution of the disks, radial stresses formed on the inner and outer parts of the disks were calculated by assuming that the modulus of elasticity does not change with temperature at temperatures of 30 °C, 60 °C, 90 °C, 120 °C on the inner and outer surfaces of the disk. During the study, analytical and numerical analysis was performed using a computer program and mathematically modeled ANSYS programs. Both methods give similar results. In other words, the differences analytical and numerical results can be ignored. At the end of this study, it was determined that the radial and tangential stress values were higher at high temperatures than at low temperatures. It has been established that tangential stresses are much larger than radial stresses. The purpose of this article is to study the behavior of the thermal load on two different thermoplastic disks.

Abstract

In this study, elastic stress analysis was performed on thermoplastic composite discs. The modulus of elasticity of thermoplastic composite discs is also different from each other. Our goal is to study elastic stretching. The field of application of primitive stresses caused by uneven temperature distribution in engineering is quite large. Under the parabolic temperature distribution of the disks, radial stresses formed on the inner and outer parts of the disks were calculated by assuming that the modulus of elasticity does not change with temperature at temperatures of 30 ° C, 60 ° C, 90 ° C, 120 ° C on the inner and outer surfaces of the disk. During the study, analytical and numerical analysis was performed using a computer program and mathematically modeled ANSYS programs. Both methods give similar results. In other words, the differences dec analytical and numerical results can be ignored. At the end of this study, it was determined that the radial and tangential stress values were higher at high temperatures than at low temperatures. It has been established that tangential stresses are much larger than radial stresses. The purpose of this article is to study the behavior of the thermal load on two different thermoplastic disks.

🔖

Bu Makaleye Atıf Yap

KAYIRAN, H. F. (2021). ANALYTICAL AND NUMERICAL INVESTIGATION OF ELASTIC STRESSES IN THERMOPLASTIC MATRIX COMPOSITE DISCS UNDER TEMPERATURE EFFECT. International Journal of 3D Printing Technologies and Digital Industry, Cilt: 5 - Sayı: 3, 730–741. https://ajindex.com/articles/672290

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (13)

  1. Doğan, A., Arıkan, V., “Low-velocity impact response of e-glass reinforced thermoset and thermoplastic based sandwich composites”, Materials Science Composites Part B-engineering, Vol. 127, Issue 1, Pages 63-69, 2017.
  2. Kayıran, H.F., “Investigation of thermal stress behavior of discs with different diameters of aluminum (Al2024- T3) boron carbide (B4C)”, 4th International Mediterranean Symposium, Pages 81-98, Mersin, 2020.
  3. Kayıran, H.F., “Thermal stress analysis in a bimaterial disc”, Master Thesis, Süleyman Demirel University Institute of Science, Mechanical Engineering Department, Isparta, 2012.
  4. Durodola, J., Attia, O., “Deformation and stresses in functionally graded rotating discs”, Composites Science and Technology, Vol. 60, Issue 1, Pages 987-995, 2000.
  5. Şen, F., Pekbey, Y., Sayman,O., “Elastic-plastic stress analysis of a thermoplastic composite disc under parabolic temperature distribution”, Indian Journal of Engineering and Materials Sciences, Vol. 14, Issue 1, Pages 282-288, 2007.
  6. Akay, M., Özden, S., “Measurement of residual stresses in injection molded thermoplastics”, Polymer Testing, Vol. 13, Issue 1, Pages 323-354, 1994.
  7. Örçen, G., Gür, M., Solmaz, M.Y., “Plastic stress analysis in elliptical perforated thermoplastic layered composite plates”, Journal of the Faculty of Engineering and Architecture of Gazi University, Vol. 24, Issue 4, Pages 667-674, 2009.
  8. Kısmet, Y., Doğan A., “Characterization of the mechanical and thermal properties of rape short natural-fiber reinforced thermoplastic composites”, Iranian Polymer Journal, Vol. 5, Issue 1, Pages 1-9, 2021.
  9. Karakuzu, R., Djele, A., Doğan, A., “High temperature effect on quasi-static and low velocity impact behaviors of advanced composite materials, proceedings of the institution of mechanical engineers, part c: journal of mechanical engineering science”, Vol. 235, Issue 23, Pages 7110-7119, 2021.
  10. Doğan, A., Arman, Y., “The effect of hygrothermal aging on the glass and carbon reinforced epoxy composites for different stacking sequences”, Mechanics Of Solid Bodies, Vol. 24, Issue 1, Pages 19-25, 2018.
  11. Evlen, H., Erel, G., “Effect of the reinforcement phase on the mechanical and biocompatibility properties of pla matrix nano composites”, Vol. 45, Issue 4, Pages 491, 500, 2021.
  12. Evlen, H., Akçaer, E.,“Effects of carbon nanotube ratio on mechanical and morphological properties of a356–carbon nanotube composites”, Acta Physica Polonica, Vol. 135, Issue 1, Pages 668-671, 2009.
  13. Kayıran, H.F., “Numeri