Dergiler / Teknik Dergi / 2018 / Cilt: 28 - Sayı: ek

Seismic Strengthening of Beam-Column Joints Using Diagonal Steel Bars

Sayfa
2117–2130
Yayın Tarihi
2022-10-18
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Total of eleven specimens were tested, where four were reference specimens and remaining seven were strengthened at the joint region with diagonal steel bars

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:It is known that beam-column connections are subjected to high stresses during earthquakes.
📊
Temel Bulgular & Veri:This experimental study was carried out at the METU Structural Mechanics Laboratory by using T-shaped test specimens reflecting an exterior joint region of a frame having usual dimensions reduced to a scale of approximately 2/3.
💡
Sonuç & Katkı:Total of eleven specimens were tested, where four were reference specimens and remaining seven were strengthened at the joint region with diagonal steel bars
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Alan Parametreleri

Abstract

It is known that beam-column connections are subjected to high stresses during earthquakes. Therefore, the design of these connections plays an important role for an earthquake resistant structure. Closely spaced stirrups should be used in beam-column connections to carry these stresses safely. Since the placement of ties required by the code in this region is rather difficult, this condition is ignored in many cases. Consequently, beam-column joints are sometimes deficient in terms of seismic behavior. In a beam-column connection which has no sufficient shear reinforcement, it is suggested that additional reinforcement arranged by placing steel bars into diagonal holes drilled from the outside and anchoring them by epoxy can carry principal tensile stresses in beam-column connections. This experimental study was carried out at the METU Structural Mechanics Laboratory by using T-shaped test specimens reflecting an exterior joint region of a frame having usual dimensions reduced to a scale of approximately 2/3. Total of eleven specimens were tested, where four were reference specimens and remaining seven were strengthened at the joint region with diagonal steel bars

🔖

Bu Makaleye Atıf Yap

GÖKDEMİR, H., TANKUT, T. (2022). Seismic Strengthening of Beam-Column Joints Using Diagonal Steel Bars. Teknik Dergi, Cilt: 28 - Sayı: ek, 2117–2130. https://ajindex.com/articles/596569

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (6)

  1. Antonopoulos, C. P., Triantafillou, T. C., Exp Investigation of FRP Strengthened RC Beam-Column Joints, Journal of Composites for Construction, 344(7), 39-49, 2003
  2. Ghobarah, A., Said, A., Seismic Rehabilitation of Beam-Column Joints Using FRP Laminates, Journal of Earthquake Engineering, 5(1), 113-129, 2001
  3. Prota, A., Nanni, A., Manfredi, G., Cosenza, E., Selective Upgrade of Under-designed RC Beam-Column Joints Using CFRP, ACI Structural Journal, 101(11), 699-707, 2004
  4. Taslıgedik, A.Ş., “Lap Splice Behaviour of CFRP Rolls”, MSc thesis, Middle East Technical University, Ankara, Turkey, 2008
  5. Gokdemir, H., “Seismic Strengthening of Beam-Column Joints”, PhD thesis, Eskisehir Osmangazi University, Eskisehir, Turkey, 2009
  6. Seckin, M., “Hysteretic Behaviour of Cast-in-Place Exterior Beam-Column SubAssemblies”, PhD thesis, Toronto University, Toronto, Canada, 1981.