Dergiler / Journal of Structural Engineering & Applied Mechanics (Online) / 2022 / Cilt: 5 - Sayı: 3

Effect of fiber type and thickness on mechanical behavior of thermoplastic composite plates reinforced with fabric plies

Sayfa
161–169
Yayın Tarihi
2022-10-19
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Using hybrid fabric instead of glass as fiber material increased the maximum damage load by 100%.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Studies on weight reduction in aviation and space vehicles have gained momentum recently.
📊
Temel Bulgular & Veri:As the number of layers increased, stiffness, damage load and deformations increased in thermoplastic composites.
💡
Sonuç & Katkı:Using hybrid fabric instead of glass as fiber material increased the maximum damage load by 100%.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Alan Parametreleri

Abstract

Studies on weight reduction in aviation and space vehicles have gained momentum recently. Thermoplastic matrix composite materials are important alternative materials, especially due to their high specific strength, formability and recyclability. In this study, it is aimed to investigate the mechanical behavior of fiber reinforced thermoplastic composites for different fiber and layer configurations. Thermoplastic composite materials used in the study were produced by lamination technique. In composite production; Glass fiber and carbon-aramid hybrid fabrics were used as fiber, and polyethylene granules were used as matrix. Thermoplastic sheets were obtained by keeping polyethylene granules and woven fibers in the hot press for a certain period of time. The damage behavior of the composite test specimens under tensile load was tested for the number of layers and fiber type. As the number of layers increased, stiffness, damage load and deformations increased in thermoplastic composites. Using hybrid fabric instead of glass as fiber material increased the maximum damage load by 100%.

🔖

Bu Makaleye Atıf Yap

ÖZTEKİN, H. F., GÜR, M., KAMAN, M. O., ERDEM, S. (2022). Effect of fiber type and thickness on mechanical behavior of thermoplastic composite plates reinforced with fabric plies. Journal of Structural Engineering & Applied Mechanics (Online), Cilt: 5 - Sayı: 3, 161–169. https://ajindex.com/articles/566344

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (1)

  1. Russo P, Acierno D, Simeoli G, Iannace S, Sorrentino L (2013) Flexural and impact response of woven glass fiber fabric/polypropylene composites. Compos. Part B Eng. 54(1):415–421. doi: 10.1016/j.compositesb.2013.06.016. Steggall-Murphy C, Simacek P, Advani SG, Yarlagadda S, Walsh S (2010) A model for thermoplastic melt impregnation of fiber bundles during consolidation of powder-impregnated continuous fiber composites. Compos. Part A Appl. Sci. Manuf. 41(1):93–100. doi: 10.1016/j.compositesa.2009.09.026. Van Vuure AW, Vanderbeke J, Mosleh Y, Verpoest I, El-Asmar N (2021) Ductile woven silk fibre thermoplastic composites with quasi-isotropic strength. Compos. Part A Appl. Sci. Manuf. 147:106442. doi: 10.1016/j.compositesa.2021.106442. Sun Z, Guo FL, Wu XP, Li YQ, Zeng W, Chen Q, Huang T, Huang P, Fu YQ, Ma XY, Hu N, Fu SY (2022) Experimental and simulation investigations of the effect of hybrid GO-thermoplastic polyimide sizing on the temperature-dependent tensile behavior of short carbon fiber/polyetherimide composites. Compos. Sci. Technol. 218:109166. doi: 10.1016/j.compscitech.2021.109166. Katti SR, Achutha MV, Sridhara BK (2020) Tensile behaviour of MWCNT and CNP filled polypropylene thermoplastic composites. Mater. Today Proc. 43:1678–1683. doi: 10.1016/j.matpr.2020.10.034. Forsgren L, Noyan ECB, Vega A, Yarahmadi N, Boldizar A (2020) The thermo-oxidative durability of polyethylene reinforced with wood-based fibres. Polym. Degrad. Stab. 181: 109374. doi: 10.1016/j.polymdegradstab.2020.109374. Das SC, Paul D, Grammatikos SA, Siddiquee MAB, Papatzani S, Koralli P, Islam JMM, Khan MA, Shauddin SM, Khan RA, Vidakis N, Petousis M (2021) Effect of stacking sequence on the performance of hybrid natural/synthetic fiber reinforced polymer composite laminates. Compos. Struct. 276:114525. doi: 10.1016/j.compstruct.2021.114525. Obande W, Brádaigh CMÓ, Ray D (2020) Thermoplastic hybrid-matrix composite prepared by a room temperature vacuum infusion and in-situ polymerisation process. Compos. Commun. 22:22–27. doi: 10.1016/j.coco.2020.100439. Chukov D, Torokhov V, Sherif G, Tcherdyntsev V (2020) Thermal treatment as an effective method of carbon/glass fibers surface modification for high-performance thermoplastic polymer matrix composites. Mater. Today Proc. 33:2027–2031. doi: 10.1016/j.matpr.2020.08.331. Gebhardt M, Manolakis I, Kalinka G, Deubener J, Chakraborty S, Meiners D (2021) Re-use potential of carbon fibre fabric recovered from infusible thermoplastic CFR