KaydedilenlerDerginizi ekleyin

Dergiler / International Journal of Automotive Engineering and Technologies / 2015 / Cilt: 4 - Sayı: 1

Design and optimization of chemical mixing system for vacuum chambers base of simulation results

F. ÜNKER
E. KAPLAN
O. ÇUVALCI
Sayfa
23–32
Yayın Tarihi
2022-10-18
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

The parametric study has demonstrated that CFD is a powerful tool to study theproblem of gas flow structure interaction on funnel and is capable of providing a means ofvisualizing the path of the gas under different operating conditions .

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Computational fluid dynamics (CFD) is widely used in device design to determine gas flowpatterns and turbulence levels.
📊
Temel Bulgular & Veri:The results presented have been analyzed for a total of 11 different cases by varyingneck and nozzle angles for a process gas.
💡
Sonuç & Katkı:The parametric study has demonstrated that CFD is a powerful tool to study theproblem of gas flow structure interaction on funnel and is capable of providing a means ofvisualizing the path of the gas under different operating conditions .
🔬Tür:Modelleme & Sayısal Simülasyon
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Alan Parametreleri

Abstract

Computational fluid dynamics (CFD) is widely used in device design to determine gas flowpatterns and turbulence levels. CFD is also used to simulate particles and droplets, which aresubjected to various forces, turbulence and wall interactions. These studies can now beperformed routinely because of the availability of commercial software containing highquality turbulence and particle models. In order to understand how the gas is brought down towafer, it is necessary to have a knowledge of the gas flow behavior very early in t he designspiral of the Tantalum nitride - Atomic layer deposition ( TaN- ALD) chamber by undertakingparametric investigation of the interaction effect between gas flow and the funnel structure.This paper presents such a parametric investigation on a generic TaN- ALD chamber usingCFD. The results presented have been analyzed for a total of 11 different cases by varyingneck and nozzle angles for a process gas. The gas flow was mainly investigated for the nozzleangles of 4.5 , 9 , 12 and 20 and the film thi ckness results were compared with numericalflow patterns. CFD simulations using the turbulence model in ANSYS Fluent v.13 areundertaken. The parametric study has demonstrated that CFD is a powerful tool to study theproblem of gas flow structure interaction on funnel and is capable of providing a means ofvisualizing the path of the gas under different operating conditions .

🔖

Bu Makaleye Atıf Yap

ÜNKER, F., KAPLAN, E., ÇUVALCI, O. (2022). Design and optimization of chemical mixing system for vacuum chambers base of simulation results. International Journal of Automotive Engineering and Technologies, Cilt: 4 - Sayı: 1, 23–32. https://ajindex.com/articles/540382

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (17)

  1. ISO/DIS 3570/1, 1975
  2. Poulter K. F., “The calibration of vacuum gauges,” J. Phys. E: Sci. Ins trum., vol. 10, pp.112. 1977
  3. Szwemin P., “The influence of the blocking plate diameter on the gas flux distribution in the calibration chamber”,Vacuum, vol. 73, pp.263. 2004
  4. Maev R., and Leshchynsky V., Introduction to low pressure gas dynamic spray. Weinheim, Germany: Wiley- Vch. 2008
  5. Cai C., and Boyd I.D., Nov. “Collisionless Gas Flow Expanding into Vacuum,” Journal of Spacecraft and Rockets, vol.44, pp.1326- 1330. 2007
  6. Versteeg H.K., and Malalasekera W., An Introduction to Computational Fluid Dynamics. The Finite Volume Approach, Addison Wesley Longman, Harlow, UK. 1995
  7. T u J., Yeoh G.H., and Liu C., Computational Fluid Dynamics. A Practical Approach, Elsevier, Oxford, UK. 2008
  8. Patankar S.V., Numerical Heat Transfer and Fluid Flow, Series in Computational Methods in Mechanics and Thermal Sciences, Taylor and Francis. 1980
  9. Ferziger J.H., and Peric M., Computational Methods for Fluid Dynamics. 2002
  10. Launder B.E., and Spalding D.B., “The numerical computation of turbulent flows,” Comput. Meth. Appl. Mech. Eng. vol.3, pp. 269–289. 1974
  11. Menter F.R., “Two- equation eddy– viscos ity turbulence models for engineering applications,” AIAA J., vol32, pp.1598–1605. August 1994
  12. Versteeg H.K., Hargrave G., Harrington L., Shrubb I., and Hodson D., “The use of computational fluid dynamics (CFD) to predict pMDI air flows and aerosol plume formation,” Respiratory Drug Delivery VII, vol.1, pp. 257–264. 2000
  13. Lai Jr. M., Huang C.Y., Chen C.H., Linliu K., and Lin J.D., “Influence of liquid hydrophobicity and nozzle passage curvature onmicrofluidic dynamics in a drop ejection process,” J. Micromech. Microeng. vol. 20, 015033, p.14. 2010
  14. Nichols S.C., and Wynn E., “New approaches to optimizing dispersion in dry powder inhalers — dispersion force mapping and adhesion measurements,” Respir. Drug Deliv., vol. 1, pp. 175–184. 2008
  15. Coates M.S., Chan H. - K., Fletcher D.F., and Raper J.A., “Influence of air flow on the performance of a dry powder inhaler using computational and experimental analyses,” Pharm. Res., vol. 22, pp. 1445–1453. 2005
  16. Coates M.S., Fletcher D.F., Chan H. - K., and Raper J.A., “Effect of design on the performance of a dry powder inhaler using computational fluid dynamics. Part 1: grid structure and mouthpiece length,” J. Pharm. Sci., vol. 93, pp. 2863 –2876. 2004
  17. Coates M., Chan H. - K., Fletc