KaydedilenlerDerginizi ekleyin

Dergiler / International Advanced Researches and Engineering Journal / 2022 / Cilt: 6 - Sayı: 2

Hydroxyapatite coating processes with EPD method and investigation of mechanical properties of coatings

İbrahim AYDIN
Ali İhsan BAHÇEPINAR
Mehmet AYVAZ
Sayfa
106–112
Yayın Tarihi
2022-10-19
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

When the nano indentation test results were evaluated, it was observed that coatings suitable for shell bone implants were obtained.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:This paper reports on electrophoretic deposition of hydroxyapatite coatings on 316L stainless steel and Ti6Al4V alloy.
📊
Temel Bulgular & Veri:Coatings were carried out at 60 sec. deposition time and voltage values of 40, 80, 120, 160 Voltage.
💡
Sonuç & Katkı:When the nano indentation test results were evaluated, it was observed that coatings suitable for shell bone implants were obtained.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Electrophoretic Deposition · Hydroxyapatite · Ti6Al4V

Abstract

This paper reports on electrophoretic deposition of hydroxyapatite coatings on 316L stainless steel and Ti6Al4V alloy. Coatings were carried out at 60 sec. deposition time and voltage values of 40, 80, 120, 160 Voltage. Suspension: It was prepared by using Ethanol, Hydroxyapatite, Polyvinyl Alcohol, Sodium dodecyl sulfate, N-N-Dimethylformamide chemicals. The findings and results acquired at the end of the study have been presented and discussed. When the Ca/P values calculated in the study are examined, it was seen that there are values close to the ideal Ca/P ratio (1.67) in all parameters. When the roughness values are examined, it was seen that coatings close to the ideal surface roughness value (1-1.5 µm) are obtained. When the nano indentation test results were evaluated, it was observed that coatings suitable for shell bone implants were obtained.

🔖

Bu Makaleye Atıf Yap

AYDIN, İ., BAHÇEPINAR, A. İ., AYVAZ, M. (2022). Hydroxyapatite coating processes with EPD method and investigation of mechanical properties of coatings. International Advanced Researches and Engineering Journal, Cilt: 6 - Sayı: 2, 106–112. https://ajindex.com/articles/539250

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (12)

  1. Prabakaran, K., Thamaraiselvi, T. V. and Rajeswari, S., Electrochemical evaluation of hydroxyapatite reinforced phosphoric acid treated 316L stainless steel. Trends Biomaterials, 2006. 19: p. 84-87
  2. Aydin, I., Cetinel, H., Pasinli, A. and Yuksel, M., Preparation of hydroxyapatite coating by using citric acid sodium citrate buffer system in the biomimetic procedure. Materials Testing, 2013. 55(10): p. 782-788
  3. He, G., and Hagiwara, M., Ti alloy design strategy for biomedical applications. Materials Science and Engineering: C, 2006. 26(1): p. 14-19
  4. Javidi, M., Javadpour, S., Bahrololoom, M. E. and Ma, J. J. M. S., Electrophoretic deposition of natural hydroxyapatite on medical grade 316L stainless steel. Materials Science and Engineering: C, 2008. 28(8): p. 1509-1515
  5. Bogdanoviciene, I., Beganskiene, A., Tonsuaadu, K., Glaser, J., Meyer, H. J. and Kareiva, A., Calcium hydroxyapatite, Ca10(PO4)6(OH)2 ceramics prepared by aqueous sol–gel processing. MaterialsResearch Bulletin, 2006. 41(9): p. 1754-1762
  6. Farrokhi-Rad, M.,Electrophoretic deposition of hydroxyapatite nanoparticles: effect of suspension composition on the electrochemical potential difference at deposit/suspensions interface. Materials Research Express, 2018. 5(8): 085005
  7. Iqbal, N., Nazir, R., Asif, A., Chaudhry, A. A., Akram, M., Fan, G. Y. and Hussain, R., Electrophoretic deposition of PVA coated hydroxyapatite on 316L stainless steel. Current Applied Physics, 2012. 12(3): p. 755-759
  8. Tian, Q., Lin, J., Rivera-Castaneda, L., Tsanhani, A., Dunn, Z. S., Rodriguez, A. and Liu, H., Nano-to-submicron hydroxyapatite coatings for magnesium-based bioresorbable implants–deposition, characterization, degradation, mechanical properties, and cytocompatibility. Scientific reports, 2019. 9(1): p. 1-27
  9. Surmenev, R. A., A review of plasma-assisted methods for calcium phosphate-based coatings fabrication. Surface and Coatings Technology, 2012. 206(8-9): p. 2035-2056
  10. Suchanek, K., Bartkowiak, A., Perzanowski, M., Marszałek, M., Sowa, M. and Simka, W., Electrochemical properties and bioactivity of hydroxyapatite coatings prepared by MEA/EDTA double-regulated hydrothermal synthesi. Electrochimica Acta, 2019. 298: p. 685-693
  11. Miranda, G., Sousa, F., Costa, M. M., Bartolomeu, F., Silva, F. S., and Carvalho, O., Surface design using laser technology for Ti6Al4V-hydroxyapatite implants. Optics & Laser Technology, 2019. 109: p. 488-495
  12. Luo, J., Jia, X., Gu, R., Zhou, P., Huang,