Dergiler / Düzce Üniversitesi Bilim ve Teknoloji Dergisi / 2019 / Cilt: 7 - Sayı: 1

Çelik Tel Örgülerin Betonarme Kirişlerin Kesme Davranışına Etkisi

Effect of The Steel Wired Mesh On the Shear Behavior of RC Beams

Sayfa
477–487
Yayın Tarihi
2022-10-12
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Kesme donatısı olarak etriyelere ilaveten çelik tel örgülerin kullanılması durumunda ise betonarme kirişlerin yük taşıma kapasiteleri, başlangıç rijitlikleri ve yerdeğiştirme süneklikleri önemli oranda artmıştır.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Çelik tel örgülerin çimento hamuruyla birlikte uygulanması neticesinde meydana gelen ferro-çimento, mevcut betonarme yapı elemanlarının güçlendirilmesinde kullanılan bir yöntemdir.
📊
Temel Bulgular & Veri:Bu çalışmada ise, çelik tel örgülerin kesme donatısı olarak kullanılmasının betonarme kirişlerin davranışlarına etkileri deneysel olarak araştırılmıştır.
💡
Sonuç & Katkı:Kesme donatısı olarak etriyelere ilaveten çelik tel örgülerin kullanılması durumunda ise betonarme kirişlerin yük taşıma kapasiteleri, başlangıç rijitlikleri ve yerdeğiştirme süneklikleri önemli oranda artmıştır.
🔬Tür:Araştırma Makalesi
📍Kapsam:2000 Verileri
⚙️Değişkenler:Çelik tel örgü · Dört nokta eğilme deneyi · Betonarme kiriş

Özet

Çelik tel örgülerin çimento hamuruyla birlikte uygulanması neticesinde meydana gelen ferro-çimento, mevcut betonarme yapı elemanlarının güçlendirilmesinde kullanılan bir yöntemdir. Bu çalışmada ise, çelik tel örgülerin kesme donatısı olarak kullanılmasının betonarme kirişlerin davranışlarına etkileri deneysel olarak araştırılmıştır. Bunun için 150*300*2000 mm ebatlarında ve farklı donatı düzenine sahip üç adet betonarme kiriş üretilerek dört nokta eğilme testine tabi tutulmuştur. Sonuçta, çelik tel örgülerin kirişin çatlama mekanizmasını iyileştirerek geniş çatlakları azaltıp kılcal çatlakları artırdığı görülmüştür. Ancak, kesme donatısı olarak yalnızca çelik tel örgü kullanımı çatlamış kirişte erken dayanım kaybına neden olmuştur. Kesme donatısı olarak etriyelere ilaveten çelik tel örgülerin kullanılması durumunda ise betonarme kirişlerin yük taşıma kapasiteleri, başlangıç rijitlikleri ve yerdeğiştirme süneklikleri önemli oranda artmıştır.

Abstract

Ferro-cement made of steel wired mesh and cement mortar is a method using for strengthening of existing reinforced concrete structures. In this study, the effects of the steel wired mesh on the shear behavior of reinforced concrete beams were investigated experimentally. For this purpose, three reinforced concrete beams having 150x300x2000 mm dimensions and different reinforcements were produced and subjected to four point bending tests. As a result, steel wired mesh improved the cracking mechanism of the beam by reducing the number of large cracks while increasing minor cracks. However, the use of steel wired mesh has caused early strength loss of the cracked beam. In the case of the usage of steel wired mesh in addition to the stirrups as shear reinforcement, the load bearing capacities, initial stiffness and displacement ductility of the reinforced concrete beams have significantly increased.

🔖

Bu Makaleye Atıf Yap

DEMİR, S. (2022). Çelik Tel Örgülerin Betonarme Kirişlerin Kesme Davranışına Etkisi. Düzce Üniversitesi Bilim ve Teknoloji Dergisi, Cilt: 7 - Sayı: 1, 477–487. https://ajindex.com/articles/494451

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (16)

  1. A. Cladera and A. R. Mari, ''Experimental study on high-strength concrete beams failing in shear,'' Engineering Structures, vol. 27, pp. 1519-1527, 2005
  2. EERI Special Earthquake Report, ''The Izmit (Kocaeli), Turkey earthquake of August 17, 1999,'' EERI, California, 1999
  3. EERI Special Earthquake Report, ''The mw 7.1 Erciş-Van, Turkey earthquake of October 23, 2011,'' EERI, California, 2012
  4. Building Code Requirements for Structural Concrete (ACI 318-02) and Commentary (ACI 318R-02), American Concrete Institute, 2002
  5. Design of Structures for Earthquake Resistance, EN 1998-1 -Part 1: General Rules, Seismic Actions and Rules For Buildings, CEN, 2004
  6. Deprem Bölgelerinde Yapılacak Binalar Hakkında Yönetmelik, Bayındırlık ve İskan Bakanlığı, 2007
  7. L. S. Beedle and D. B. Rice, Structural Systems For Tall Buildings, New York, USA: McGraw-Hill, 1995
  8. C. Cucchiara, L. L. Mendola and M. Papia, ''Effectiveness of stirrups and steel fibres as shear reinforcement,'' Cement and Concrete Composites, vol. 26, pp. 777-786, 2004
  9. A. Ding, Y. Zhiguo and J. Said, ''The composite effect of steel fibres and stirrups on the shear behaviour of beams using self-consolidating concrete,'' Engineering Structures, vol. 33, pp. 107-117, 2011
  10. G. Russo, D. Mitri and M. Pauletta, ''Shear strength design for rc beams with stirrups,'' Engineering Structures, vol. 51, pp.226-235, 2013
  11. K. Takiguchi and Abdullah, ''Shear strengthening of rc columns with ferrocement,'' ACI Structural Journal, vol. 98, no. 5, pp. 696-704, 2001
  12. Abdullah and K. Takiguchi, ''An investigation into the behaviour and strength of reinforced concrete columns strengthened with ferrocement jackets,'' Cement and Concrete Composites, vol. 25, pp. 233-242, 2003
  13. H. H. Nassif and H. Najm, ''Experimental and analytical investigation of ferrocement-concrete composite beams,'' Cement and Concrete Composites, vol. 24, pp. 787-796, 2004
  14. P. P. Bansal, M. Kumar and S. K. Kaushik, ''Effect of wire mesh orientation on strength of beams retrofitted using ferrocement jackets,'' International Journal of Engineering, vol. 2, no. 1, pp. 8-19, 2006
  15. M. J. Chajes, T. F. Januska, D. R. Mertz, T. A. Thomson and W. W. Finch, ''Shear strengthening of reinforced concrete beams using externally applied composite fabrics,'' ACI Structural Journal, vol. 92, no. 3, pp. 295-303, 1995
  16. T. C. Triantafillou, ''Shear strengthening of reinforced concrete beams using epoxy-bonded fr