KaydedilenlerDerginizi ekleyin

Dergiler / Tekstil ve Konfeksiyon / 2015 / Cilt: 25 - Sayı: 2

ADAMS KULLANARAK CM500 PENYE MAKINELERİNDE KISKAÇ MEKANİZMASI OPTİMİZASYONU ÜZERİNE ARAŞTIRMA

RESEARCH ON OPTIMIZATION OF NIPPER MECHANISM ON CM500 COMBERS USING ADAMS

Xuzhong SU
Weidong GAO
Xinjin LIU
Chunping XIE
Bojun XU
Sayfa
151–154
Yayın Tarihi
2015-12-01
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

The results obtained in this paper provide a theoretical support for product design

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Comber is one of the important equipments on cotton yarn spinning.
📊
Temel Bulgular & Veri:In this paper, the research on optimization of nipper mechanism on CM500 series Combers was discussed using ADAMS software.
💡
Sonuç & Katkı:The results obtained in this paper provide a theoretical support for product design
🔬Tür:Modelleme & Sayısal Simülasyon
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Comber · Nipper mechanism · Optimization

Abstract

Comber is one of the important equipments on cotton yarn spinning. In this paper, the research on optimization of nipper mechanism on CM500 series Combers was discussed using ADAMS software. First, the nipper mechanisms moving characteristics of CM500 Combers was analyzed and the models of displacement, velocity, acceleration of nipper balance shaft were given. Then, the optimization of nipper system was discussed by using ADAMS software, and corresponding optimal crank radius was addressed. The simulation results show that vibrations of nipper are decreased significantly by optimization. The results obtained in this paper provide a theoretical support for product design

🔖

Bu Makaleye Atıf Yap

SU, X., GAO, W., LIU, X., XIE, C., XU, B. (2015). ADAMS KULLANARAK CM500 PENYE MAKINELERİNDE KISKAÇ MEKANİZMASI OPTİMİZASYONU ÜZERİNE ARAŞTIRMA. Tekstil ve Konfeksiyon, Cilt: 25 - Sayı: 2, 151–154. https://ajindex.com/articles/46162

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (9)

  1. Erdogan M.C. and Pamuk O., 2007, Technical TextilesR21,Tekstil ve Konfeksiyon, Vol: 17(3), pp: 211-216
  2. Liang J. J., Yang M. Q., Zhang W., Zhang J. R. and Sun Q. H., 2008, Vibration Analysis and Control for the Headstock system of cotton Comber, Noise and Vibration Control, Vol: 8, pp: 27-30
  3. Subramanian S. and Gobi N., 2004, Effect of process parameters at comber on yam and fabric properties, Indian Journal of Fiber & Textile Research, Vol: 29(2), pp: 196-199
  4. Chellamani K. P., Chattopadhyay D. and Thanabal V., 2003, Influence of wire point density in cards and combers on neps in sliver and yarn quality, Indian Journal of Fiber & Textile Research, Vol: 28(1), pp: 9-15
  5. Belin R. E. and Taylor D. S., The Influence of Hooked Fibers on Cotton Comber Waste, Textile Research Journal, Vol: 36(6), pp:542-546
  6. Schlatter N., 2005, Rieter enhances efficiency in combers by produced a new comber moderl E65/E75, TEKSTIL, Vol: 54(2), pp: 89-90
  7. Chattopadhyay R. and Ghosh R., 2003, Studies on mass distribution profile of detached fibre fringe in a comber, Indian Journal of Fiber & Textile Research, Vol: 28(4), pp: 393-398
  8. Xu B. J., Ma Q. H. and Liu X. J., Dynamic Balance Optimisation for the Middle Shaft System of a Cotton Comber Based on ADAMS, FIBRES & TEXTILES in Eastern Europe, Vol: 3(92), pp: 43-45
  9. Zheng J. R., Introduction and advancement on ADAMS prototyping technology, Beijing: China Machine Press, 2002:74-108.