Dergiler / Tekstil ve Konfeksiyon / 2016 / Cilt: 26 - Sayı: 1

KUMAŞLARIN GERİLME ÖZELLİKLERİNİN ÖLÇÜMÜ İÇİN BİR TEST CİHAZININ GELİŞTİRİLMESİ

DEVELOPMENT OF A TEST DEVICE FOR MEASURING TENSILE PROPERTIES OF FABRICS

Sayfa
12–21
Yayın Tarihi
2016-06-01
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Cihazın rijitliğinin artırılması ve mekaniğinin iyileştirilmesi ile piyasada mevcut olan ticari cihazlar seviyesinde test sonuçlarının elde edilebileceğini değerlendirmekteyiz

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Tekstil malzemeleri için mekanik özellikleri ölçen bir test cihazı tasarlanıp imal edildi ve performansı test edildi.
📊
Temel Bulgular & Veri:Yapılan testlerde cihaz ve Instron 4301’den elde edilen yük uzama eğrileri birbirine yakın olarak elde edilmesine rağmen bazı sapmaların halen mevcut olduğu görülmektedir.
💡
Sonuç & Katkı:Cihazın rijitliğinin artırılması ve mekaniğinin iyileştirilmesi ile piyasada mevcut olan ticari cihazlar seviyesinde test sonuçlarının elde edilebileceğini değerlendirmekteyiz
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Gerilme özellikleri · gerilme özellikleri test cihazı · test cihazı tasarımı

Özet

Tekstil malzemeleri için mekanik özellikleri ölçen bir test cihazı tasarlanıp imal edildi ve performansı test edildi. Hareketli çenenin tahrikinde servo motor ve bilyalı vida mekanizması ile gerçekleştirildi ve hareketli çenenin yer değiştirme miktarı servo motor hareketi ve vida dişli kinematiğinden hesaplandı. Gerginlik ölçümü ise dğişik ölçüm aralıklarına sahip yük hücreleri ile gerçekleştirildi. Yük uzama eğrisi, sabit uzama altında gerginlik değişimi, creep testi ve tekrarlı yük altında kuvvet ve uzama değişimi gibi testler için yazılım modülleri geliştirildi. Yapılan testlerde cihaz ve Instron 4301’den elde edilen yük uzama eğrileri birbirine yakın olarak elde edilmesine rağmen bazı sapmaların halen mevcut olduğu görülmektedir. Hareketli çenedeki eğilme ve sistemdeki mekanik zayıflıklar (boşluk, açıklıklar vs) bu sapmanın temel sebebi olarak değerlendirilmiştir. Cihazın rijitliğinin artırılması ve mekaniğinin iyileştirilmesi ile piyasada mevcut olan ticari cihazlar seviyesinde test sonuçlarının elde edilebileceğini değerlendirmekteyiz

Abstract

A tensile tester for textile materials has been designed, manufactured and its performance tested. Horizontal construction is preferred in the design. Servo motor and ballscrew drive is used in the drive of movable clamp and elongation of test sample is calculated from servo motor motion and gear-ballscrew kinematics. Tension is measured by load cells of different measuring intervals. Software routines have been developed for different tests including load-elongation (or stress-strain) curve, tension change under constant elongation, creep test and force and elongation lost under cyclic loading. It is shown that load-elongation curves obtained from the developed device and Instron 4301 are close to each other. But some deviations exist. This is taught to be due to the bending in the movable clamp and mechanical imperfections. With the improvement of rigidity of the device and mechanical imperfections, the device is expected to give test results of commercially available ones in the market

🔖

Bu Makaleye Atıf Yap

HASÇELİK, B., EREN, R. (2016). KUMAŞLARIN GERİLME ÖZELLİKLERİNİN ÖLÇÜMÜ İÇİN BİR TEST CİHAZININ GELİŞTİRİLMESİ. Tekstil ve Konfeksiyon, Cilt: 26 - Sayı: 1, 12–21. https://ajindex.com/articles/46139

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (1)

  1. Koc, S. K., Hockenberger, A. Ş.,2010, “Investigation of Air-Jet Texturing of Technical Polyester Yarns”, Journal of Textile & Apparel/Tekstil ve Konfeksiyon, 20(4),pp:299-305 2. Gürarda, A., Meric, B., 2010, “Slippage and Grinning Behaviour of Lockstitch Seams in Elastic Fabrics under Cyclic Loading Conditions”, Journal of Textile & Apparel/Tekstil ve Konfeksiyon, 20(1), pp:65-69. 3. Wang, X., Liu, X., Hurren, C., 2008, “Physical and Mechanical Testing of Textiles”, Fabric Testing, Ed.:Hu, J.,CRC,USA, pp: 90-123 4. Saville, B. P., 1999 “Strength and Elongation Tests”, Physical Testing of Textiles, The Textile Institute, CRC Pres.,USA, pp: 115-167 5. Wang, Y., Xia, Y., 1998, “The Effects of Strain Rate on The Mechanical Behaviour of Kevlar Fibre Bundles: An Experimental and Theoretical Study”, Composites Part A: Applied Science and Manufacturing, 29(11), pp:1411-1415. 6. Zhu, D., Mobasher, B., Rajan, S. D., 2010, “Dynamic Tensile Testing of Kevlar 49 Fabrics”, Journal of Materials in Civil Engineering, 23(3), pp:230-239. 7. Cherif, C., Seidel, A., Younes, A., et.all, 2010, “Evaluation of A Tensile Test for The Determination of The Material Behaviour of Filament Yarns under High Strain Rates” AUTEX Research Journal, 10(4), pp: 88-94. 8. Livatyali, H., 2009, “Test cihazları”, İmalat Makinaları (IML 451), Undergraduate Lecture Notes (Unpublished), İTÜ, Retrieved April 14, 2014 from http://web.itu.edu.tr/~livatyali/dersler/iml451/15_tesile_test.pdf 9. Davis, J. R., 2004, “Tensile Testing Equipment and Strain Sensors”,Tensile Testing, 2nd ed., ASM International, USA, pp:65-87 10. Gedney, R., 2005, “Tensile Testing Basics, Tips and Trends: Admet Quality Test and Inspection”, Retrieved April 14, 2014 from: http://www.admet.com/ assets/Tensile_Testing_Basics_Quality_Magazine.pdf 11. Anonymous 2009, “ASDA-B Series User Manual”, Retrieved March 27, 2014, from http://www.delta.com.tw/product/em/motion/motion_ servo/download/manual/ASDA-B_M_EN_20090628.pdf 12. Anonymous 2013, “Thomson Precision Ball Screws and Lead Screws”, Retrieved May 4, 2014, from http://www.thomsonlinear.com/ downloads/screws/Precision_Screws_ctuk.pdf 13. Anonymous 2008, “Load Cells S-type Specifications”, Retrieved July 14, 2014, from http://www.esit.com.tr/en/urun/201/100/load_cells_s_type_stcs 14. Rypl, R., Chudoba, R., Mörschel, U., et all, 2014, “A Novel Tensile Test Device for Effective Testing of High-modulus Multi-filament Yarns”, Journal of Industrial Textiles, DOI: 10.1177/15280837145