Dergiler / Tekstil ve Konfeksiyon / 2019 / Cilt: 29 - Sayı: 3

HAZARD AND RISK ANALYSIS FOR RING SPINNING YARN PRODUCTION PROCESS BY INTEGRATED FTA-FMEA APPROACH

Sayfa
208–218
Yayın Tarihi
2019-09-30
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

The results obtained from the proposed FTA-FMEA approach show that decision makers and engineers can easily decrease the number of hazards and risks with respect to both occupational health and safety in practice.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:The hazard analysis and management is vital in textile industry to avoid losing customers and wasting resources caused by the failures in production systems.
📊
Temel Bulgular & Veri:Risk analysis is also very significant to decrease possible hazards and to avoid possible damage in production systems.
💡
Sonuç & Katkı:The results obtained from the proposed FTA-FMEA approach show that decision makers and engineers can easily decrease the number of hazards and risks with respect to both occupational health and safety in practice.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:FMEA · FTA · Risk and hazard analysis

Abstract

The hazard analysis and management is vital in textile industry to avoid losing customers and wasting resources caused by the failures in production systems. Risk analysis is also very significant to decrease possible hazards and to avoid possible damage in production systems. In this study, an approach based on Failure Mode and Effects Analysis (FMEA) and Fault Tree Analysis (FTA) is proposed to analyze the ring spinning yarn production process in a textile industry. First, the possible hazards in the production line, yarn production system, in an integrated company operating in the textile sector are analyzed by FTA method. Then, FMEA is applied to ring spinning yarn production process in a textile industry to rank all possible risks corresponding to hazards in descending order with respect to both occupational health and safety. It is very important to remove all possible hazards in textile industry to decrease the number of risks related to occupational health and safety. Therefore, in total of 57 hazard root causes are determined in the yarn production department. Subsequently, the faults related to the hazard root causes are examined by FTA and then risk corresponding to these hazards are prioritized by FMEA. The results obtained from the proposed FTA-FMEA approach show that decision makers and engineers can easily decrease the number of hazards and risks with respect to both occupational health and safety in practice.

🔖

Bu Makaleye Atıf Yap

MUTLU, N. G., ALTUNTAS, S. (2019). HAZARD AND RISK ANALYSIS FOR RING SPINNING YARN PRODUCTION PROCESS BY INTEGRATED FTA-FMEA APPROACH. Tekstil ve Konfeksiyon, Cilt: 29 - Sayı: 3, 208–218. https://ajindex.com/articles/45970

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (14)

  1. Mikulak RJ, McDermott R, Beauregard M. 2008. The basics of FMEA. New York:CRC Press
  2. Küçük M, Güner M. 2014. The determination of 2nd quality and export surpluses evaluation efficiency of apparel companies with the methods of performance matrix and fuzzy logic. Tekstil ve Konfeksiyon 24(4), 386-392
  3. Küçük M, Güner M. 2015. Bir konfeksiyon işletmesinde süreç analizi yolu ile verimlilik artırma çalışması. Tekstil ve Mühendis 22(98), 33-41
  4. Güner M, İşler M. 2013. The effect of model change processes on the overall equipment effectiveness in clothing production. Tekstil ve Konfeksiyon 23(3), 297-302
  5. Burduk A, Krenczyk D. 2017. June, Risk assessment in a parallel production system with the use of FMEA method and linguistic variables, In IFIP International Conference on Computer Information Systems and Industrial Management, Cham.:Springer, 10244, 379-390
  6. Press D. 2003. Guidelines for Failure Mode and Effects Analysis (FMEA), for Automotive, Aerospace, and General Manufacturing Industries. USA:CRC Press
  7. Peddada K. 2014. Risk Assessment and Control, Governance & Control in Finance & Banking: A New Paradigm for Risk & Performance”, pp:95-112
  8. Hiles A. 2010. The definitive handbook of business continuity management. UK:John Wiley & Sons
  9. Sette S, Van Langenhove L. 2002. Optimising the fibre-to-yarn production process: finding a blend of fibre qualities to create an optimal price/quality yarn. Autex Research Journal 2(2), 257-263
  10. Militký J, Kovačič V, Rubnerova J. 2002. Influence of thermal treatment on tensile failure of basalt fibers. Engineering Fracture Mechanics 69(9), 1025-1033
  11. Sette S, Boullart L, Van Langenhove L, Kiekens P. 1997. Optimizing the fiber-to-yarn production process with a combined neural network/genetic algorithm approach. Textile Research Journal 67(2), 84-92
  12. Arain FA, Tanwari A, Hafiz-Ur-Rehman S. 2012. Statistical modeling for the effect of rotor speed, yarn twist and linear density on production and quality characteristics of rotor spun yarn. Mehran University Research Journal of Engineering and Technology 31(1), 119-128
  13. Özgüney AT, Dönmez Kretzschmar S, Özçelik G, Özerdem A. 2008. The comparison of cotton knitted fabric properties made of compact and conventional ring yarns before and after the printing process. Textile Research Journal 78(2), 138-147
  14. Dönmez Kretzschmar S, Özgüney AT, Özçelik G, Özerdem A. 2007. The comparison of cotton knitted fabric properties made of compact and con