KaydedilenlerDerginizi ekleyin

Dergiler / Sigma Mühendislik ve Fen Bilimleri Dergisi / 2019 / Cilt: 37 - Sayı: 2

ANALYSIS OF SURFACE ROUGHNESS, SOUND LEVEL, VIBRATION AND CURRENT WHEN MACHINING AISI 1040 STEEL

Abidin ŞAHİNOĞLU
Abdulkadir GÜLLÜ
İbrahim ÇİFTÇİ
Sayfa
423–437
Yayın Tarihi
2019-06-01
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Furthermore as feed rate and depth of cut increased, the current value and sound level also increased.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:AISI 1040 steel is widely used for production of various parts.
📊
Temel Bulgular & Veri:In this work, turning tests were carried out on AISI 1040 steel workpieces at five different depth of cuts, four different feed rates and 4 different cutting speeds without coolant.
💡
Sonuç & Katkı:Furthermore as feed rate and depth of cut increased, the current value and sound level also increased.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:AISI 1040 · surface roughness · sound level

Abstract

AISI 1040 steel is widely used for production of various parts. This material has been studied by many researchers. In this work, turning tests were carried out on AISI 1040 steel workpieces at five different depth of cuts, four different feed rates and 4 different cutting speeds without coolant. The influence of the cutting parameters on turned part surface roughness, vibration, sound level and machine tool motor current were examined. A full factorial experimental design method was used. The Response Surface Methodology (RSM) and Analysis of Variance (ANOVA) were used to determine the effects of input parameters on the resultant surface roughness, vibration, sound level, current. The experimental results showed that increasing feed rate increased the surface roughness, vibration, sound level and current values. The most effective cutting parameter on all the output parameters was found to be the feed rate. Furthermore as feed rate and depth of cut increased, the current value and sound level also increased.

🔖

Bu Makaleye Atıf Yap

ŞAHİNOĞLU, A., GÜLLÜ, A., ÇİFTÇİ, İ. (2019). ANALYSIS OF SURFACE ROUGHNESS, SOUND LEVEL, VIBRATION AND CURRENT WHEN MACHINING AISI 1040 STEEL. Sigma Mühendislik ve Fen Bilimleri Dergisi, Cilt: 37 - Sayı: 2, 423–437. https://ajindex.com/articles/419352

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (12)

  1. Murugappan, S., Arul, S. 2017. Effect of Cryogenic Pre cooling on Chip Reduction Co-efficient during Turning of EN8 Steel Rod. Materials today proceedig, 4,8848-8855
  2. Sharma, A.K., Singh, R.K., Dixit, A.R., Tiwari, A.K. 2016. Characterization and experimental investigation of Al2O3 nanoparticle based cutting fluid in turning of AISI 1040 steel under minimum quantity lubrication (MQL). Materials Today: Proceeding, 3,1899-1906
  3. Nizamuddin, M., Agrawal, S., Patil, N. 2018. The Effect of Karanja based Soluble Cutting Fluid on Chips Formation in Orthogonal Cutting Process of AISI 1045 Steel. Procedia Manufacturing, 20,12-17
  4. Bedekar, V., Pauskar, P., Shivpuri, R., Howe, J. 2014. Microstructure and texture evolutions in AISI 1050 steel by flow forming. Procedia Engineering, 81,2355-2360
  5. Khalil, A.N.M., Ali, M.A.M., Azmi, A.I. 2015. Effect of Al2O3 nanolubricant with SDBS on tool wear during turning process of AISI 1050 with minimal quantity lubricant. Procedia Manufacturing, 2,130-134
  6. Klocke, F., Lortz, W., Trauth, D. 2018. Analysis of the dynamic chip formation process in turning. International Journal of Mechanical Sciences, 135,313-324
  7. Moganapriya, C., Rajasekar, R., Ponappa, K., Venkatesh, R., Jerome, S. 2018. Influence of Coating Material and Cutting Parameters on Surface Roughness and Material Removal Rate in Turning Process Using Taguchi Method. Materials Today: Proceedings, 5,8532-8538
  8. Hessainia, Z., Belbah, A., Yallese, M.A., Mabrouki, T., Rigal, J.F. 2013. On the prediction of surface roughness in the hard turning based on cutting parameters and tool vibrations, Measurement. 46,1671-1681
  9. Yallese, M.A., Chaoui, K., Zeghib, N., Boulanouar, L., Rigal, J.F. 2009. Hard machining of hardened bearing steel using cubic boron nitride tool. Journal of materials processing technology, 209,1092-1104
  10. Padmini, R., Krishna, P.V., Mohana, Rao, G. 2016. Effectiveness of vegetable oil based nanofluids as potential cutting fluids in turning AISI 1040 steel. Tribology International, 94,490-501
  11. Krishna, P.V., Srikant, R.R., Rao, D.N. 2010. Experimental investigation on the performance of nanoboric acid suspensions in SAE-40 and coconut oil during turning of AISI 1040 steel. International Journal of Machine Tools and Manufacture, 50,911-916
  12. Aouici, H., Yallese, M.A., Chaoui, K., Mabrouki, T., Rigal, J. 2012. Analysis of surface roughness and cutting force components in hard turning with CBN tool: Prediction model an